用柠檬酸还原的Cr3+-HPAM胶态分散体冻胶性能研究

研究了柠檬酸与重铬酸钠的反应历程、生成螯合物的结构以及Cr3 HPAM胶态分散体冻胶的性能。在75℃下用柠檬酸将重铬酸钠中的Cr6 还原为Cr3 ,同时与Cr3 发生螯合反应,生成柠檬酸铬螯合物。这种螯合物在一定条件下释放出Cr3 ,它与HPAM交联形成胶态分散体冻胶。实验表明,柠檬酸铬 HPAM胶态分散体冻胶体系最长的成冻时间为40d,最大强度为0.036MPa。用平行管岩心模型考察了冻胶的液流转向作用,调剖后高渗透层流量减小,液流转向低渗透层。     

用柠檬酸还原的Cr^3＋-HPAM胶态分散体冻胶性能研究

研究了柠檬酸与重铬酸钠的反应历程、生成螯合物的结构以及Cr^3 -HPAM胶态分散体冻胶的性能。在75℃下用柠檬酸将重铬酸钠中的Cr^6 还原为Cr^ 3 ，同时与Cr^3 发生螯合反应，生成柠檬酸铬螯合物。这种螯合物在一定条件下释放出Cr^3 ，它与HPAM交联形成胶态分散体冻胶。实验表明，柠檬酸铬-HPAM胶态分散体冻胶体系最长的成冻时间为40d，最大强度为0．036 MPa。用平行管岩心模型考察了冻胶的液流转向作用，调剖后高渗透层流量减小，液流转向低渗透层。     

缓交联铬冻胶体系影响因素分析

缓交联铬冻胶体系由部分水解聚丙烯酰胺、重铬酸钠与有机还原剂硫脲组成。由于硫脲的还原能力弱 ,因此该体系成冻时间较长 ,其终冻时间长达 8～ 10d ,可用于油藏的深部调剖。分析了铬冻胶的形成过程 ,通过测定成冻时间 (包括初冻时间及终冻时间 )和突破真空度评价了各种因素的影响。研究结果表明 ,随着交联剂质量分数的减少、pH值的升高 ,铬冻胶体系的成冻时间延长 ,强度增大 ;随着部分水解聚丙烯酰胺质量分数的增大 ,成冻时间缩短 ,强度增大 ;随着温度的升高 ,成冻时间缩短 ,强度变化不大     

长成冻时间的深部调驱剂研究

长成冻时间的深部调驱剂是以 HPAM为主的复配聚合物 ,由树脂交联剂 1 0 3交联形成的 .由冻胶强度级别的划分定性地测定成冻时间和突破真空度的方法定量测定冻胶强度 .评价了不同聚合物、交联剂及矿化度在不同温度下的成冻时间及强度 ,并作出了成冻时间及强度等值图 .结果表明 :成冻时间在 1～ 3 0 d范围内可调 ,强度 (即 p BV值 )在 - 0 .0 6 0～ - 0 .0 3 0 MPa范围内可调 .由成冻时间和强度等值图可找出具体地层条件下的不同成冻时间及不同强度调驱剂配方     

蒸汽驱用碱木素高温冻胶交联剂的研制及评价

碱木素冻胶是一种具有热稳定性且易于进入地层深部的高温堵剂,首先合成了碱木素冻胶的交联剂——水溶性酚醛树脂,优化了其合成反应条件,然后评价了碱木素高温冻胶的性能.研究结果表明:水溶性酚醛树脂的最佳合成条件为催化剂NaOH质量分数9%,甲醛与苯酚摩尔比1.8,反应温度85℃,自缩聚反应时间30 min.脱水后的水溶性酚醛树脂中羟甲基质量分数为83.54%,游离醛质量分数为0.35%,黏度为2 950 mPa.s,可在25℃下保存1个月,贮存稳定性好.在酚醛树脂质量分数为3.5%、碱木素质量分数为10%、体系pH值为9.75、高温200℃条件下碱木素冻胶的成胶时间为1.5 h,冻胶强度为0.092 MPa.成胶时间短,冻胶强度高,热稳定性好,具有较好的蒸汽调驱性能和应用前景.     

清水配置冻胶在盐水中稳定性的变化研究

本文以水溶性酚醛树脂为交联剂,以纳米颗粒为稳定剂,以HPAM以及不同AMPS含量的聚合物为成胶剂,在低盐含量的模拟注入水中制备了稳定的冻胶。研究发现,相同交联剂和聚合物用量下,AM-AMPS共聚物成胶时间比HPAM长,但成胶后强度高。评价了制备的冻胶在不同盐含量模拟水中的脱水情况,结果表明,当模拟水盐含量为10000mg/L、30000mg/L时,冻胶会吸水膨胀、强度降低;但当模拟水盐含量高于50000mg/L时,冻胶则脱水,冻胶强度提高。模拟水盐含量越高,脱水幅度越大。提高冻胶中纳米颗粒的含量或用AMPS含量高的共聚物做成胶剂,可明显降低冻胶在高盐含量中的脱水幅度。研究结果对红河油田裂缝封堵剂的开发有指导意义。     

缓交联铬冻胶体系影响因素分析

缓交联铬冻胶体系由部分水解聚丙烯酰胺，重铬酸钠与有机还原剂硫脲组成。由于硫脲的还原能力弱。因此该体系成冻时间较长，其终冻时间长达8-10d，可用于油藏的深部调剖，分析了铬冻胶的形成过程，通过测定成冻时间（包括初冻时间及终冻时间）和突破真空度评价了各种因素的影响，研究结果表明，随着交联剂质量分数的减少，pH值的升高，铬冻胶体系的成冻时间延长，强度增大；随着部分水解聚丙烯酰胺质量分数的增大。成冻时间缩短，强度增大；随着温度的升高，成冻时间缩短，强度变化不大。     

长成冻时间的深部调驱剂研究

长成冻时间的深部调驱剂是以HPAM为主的复配聚合物，由树脂交联剂103交联形成的，由冻胶强度级别的划分定性地测定成冻时间和突破真空度的方法定量测定冻胶强度，评价了不同聚合物，交联剂及矿化度在不同温度下的成冻时间及强度，并作出了成冻时间及强度等值图，结果表明：成冻时间在1－30d范围内可调，强度（即pBv值）在－0．030MPa范围内可调，由成冻时间和强度等值图可找出具体地层条件下的不同成冻时间及不同强度调驱剂配方。     

新型深部调剖堵水剂研究及应用

研制了一种以聚丙烯酰胺为主剂,复合树脂作为延迟交联剂的调剖堵水剂,并在室内考察了其性能。该堵水剂具有强度高、成胶时间在较宽范围内连续可调整、配制简单及操作方便等特点。该体系聚合物使用浓度低(0.1%~0.5%),基液粘度低,易注入;能满足温度为40~80℃的低渗透油藏调剖、堵水的技术要求;成胶时间在10 h~25 d范围内可调,满足深部调剖及大剂量调驱的技术要求;成胶后凝胶强度高,能对高渗透层(段)形成有效封堵;体系基液pH值5~7,基本呈中性,对注入设备、油水井管柱几乎不形成腐蚀;配制简单、操作方便;所有化工材料均为固体,运输储存方便。截至目前,现场累计应用290井次,效果明显。     

新型耐温堵水调剖剂的研制与性能评价

HPAM凝胶是目前国内外采用最广泛、最有效的化学堵水调剖剂,其中苯酚/甲醛体系是HPAM凝胶类堵水调剖剂最常用的交联剂。但是苯酚/甲醛交联剂气味和毒性较大,尤其是高致癌性,严重限制了其在现场的应用。首先,在室内合成了低毒水溶性的羟甲基多酚THMBPA;其次,以THMBPA为交联剂主剂,以多乙烯多胺TET为交联剂辅剂,研究了部分水解的聚丙烯酰胺HPAM与THMBPA/TET复合交联剂的凝胶动力学,考察了p H值、复合交联剂配比、温度对成胶时间和凝胶长期稳定性的影响。实验结果表明,在120℃下,该凝胶体系的成胶时间可在10~120 h范围内任意调节。在120℃下凝胶可稳定存在90 d,在90℃下可稳定存在100 d。     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.     

Tracking data management using topology of moving object database system for moving object constrained trajectory in LBS application

Advances in wireless technologies and positioning technologies and spread of wireless devices, an interest in LBS (Location Based Service) is arising. To provide location based service, tracking data should have been stored in moving object database management system (called MODBMS) with proper policies and managed efficiently. So the methods which acquire the location information at regular time intervals then, store and manage have been studied. In this paper, we suggest tracking data management techniques using topology that is corresponding to the moving path of moving object. In our techniques, we update the MODBMS when moving object arrived at a street intersection or a curved road which is represented as the node in topology and predict the location at past and future with attribute of topology and linear function. In this technique, location data that are corresponding to the node in topology are stored, thus reduce the number of update and amount of data. Also in case predicting the location,because topology are used as well as existing location information, accuracy for prediction is increased than applying linear function or spline function.