Production and characterization of ZnO nanoparticles and porous particles by ultrasonic spray pyrolysis using a zinc nitrate precursor

ZnO nanoparticles and porous particles were produced by an ultrasonic spray pyrolysis method using a zinc nitrate precursor at various temperatures under air atmosphere. The effects of reaction temperature on the size and morphology of ZnO particles were investigated. The samples were characterized by energy dispersive spectroscopy, X-ray diffraction, transmission electron microscopy, and scanning electron microscopy. ZnO particles were obtained in a hexagonal crystal structure and the crystallite shapes changed from spherical to hexagonal by elevating the reaction temperature. The crystallite size grew by increasing the temperature, in spite of reducing the residence time in the heated zone. ZnO nanoparticles were obtained at the lowest reaction temperature and ZnO porous particles, formed by aggregation of ZnO nanoparticles due to effective sintering, were prepared at higher temperatures. The results showed that the properties of ZnO particles can be controlled by changing the reaction temperature in the ultrasonic spray pyrolysis method.     

Effect of Ni content on the wear behavior of Al–Si–Cu–Mg–Ni/SiC particles composites

In recent years, the addition of Ni has been widely acknowledged to be capable of enhancing the mechanical properties of Al–Si alloys. However, the effect of Ni on the wear behaviors of Al–Si alloys and Al matrix composites, particularly at elevated temperatures, remains an understudied area. In this study, Al–Si–Cu–Mg–Ni/20wt% SiC particles(SiCp) composites with varying Ni contents were prepared by using a semisolid stir casting method. The effect of Ni content on the dry sliding wear behavior ...     

In-situ fabrication of Al(Zn)-Al2O3 graded composite using the aluminothermic reaction during hot pressing

In this study, the fabrication of multilayer Al(Zn)–Al₂O₃ with different volume fractions of Al₂O₃ was investigated. Al and ZnO powders were milled by a planetary ball mill, after which five-layer functionally graded samples were produced through hot pressing at 580℃ and 90 MPa pressure for 30 min. Formation of reinforcing Al₂O₃ particles occurred in the aluminum matrix via the aluminothermic reaction. Determination of the ignition temperature of the aluminothermic reaction was accomplished using differential thermal and thermogravimetric analyses. Scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffractometery analyses were utilized to characterize the specimens. The thermal analysis results showed that the ignition temperatures for the aluminothermic reaction of layers with the highest and lowest ZnO contents were 667 and 670℃, respectively. Microstructural observation and chemical analysis confirmed the fabrication of Al(Zn)–Al₂O₃ functionally graded materials composites with precipitation of additional Zn in the matrix. Moreover, nearly dense functionally graded samples demonstrated minimum and maximum hardness values of HV 75 and HV 130, respectively.     

Oxide coating mechanism during fluidized bed reduction: solid-state reaction characteristics between iron ore particles and MgO

Experiments on the solid-state reaction between iron ore particles and MgO were performed to investigate the coating mechanism of MgO on the iron ore particles’ surface during fluidized bed reduction. MgO powders and iron ore particles were mixed and compressed into briquettes and, subsequently, roasted at different temperatures and for different time periods. A Mg-containing layer was observed on the outer edge of the iron ore particles when the roasting temperature was greater than 1173 K. The concentration of Fe in the Mg-containing layer was evenly distributed and was approximately 10wt%, regardless of the temperature change. Boundary layers of Mg and Fe were observed outside of the iron ore particles. The change in concentration of Fe in the boundary layers was simulated using a gas–solid diffusion model, and the diffusion coefficients of Fe and Mg in these layers at different temperatures were calculated. The diffusion activation energies of Fe and Mg in the boundary layers in these experiments were evaluated to be approximately 176 and 172 kJ/mol, respectively.     

Effect of homogenization process on the hardness of Zn–Al–Cu alloys

The effect of a homogenizing treatment on the hardness of as-cast Zn–Al–Cu alloys was investigated. Eight alloy compositions were prepared and homogenized at 350 ℃ for 180 h, and their Rockwell “B” hardness was subsequently measured. All the specimens were analyzed by X-ray diffraction and metallographically prepared for observation by optical microscopy and scanning electron microscopy. The results of the present work indicated that the hardness of both alloys (as-cast and homogenized) increased with increasing Al and Cu contents; this increased hardness is likely related to the presence of the θ and τ' phases. A regression equation was obtained to determine the hardness of the homogenized alloys as a function of their chemical composition and processing parameters, such as homogenization time and temperature, used in their preparation.     

Enhancement of the nickel converter slag-cleaning operation with the addition of spent potlining

The slag cleaning (or matte settling) process was experimentally investigated at 1573 K using a fayalitic nickel converter slag containing spinel and matte/alloy particles. The addition of various amounts of spent potlining (SPL) was studied in terms of its influence on matte settling and the overall metal recoveries. The slags produced were characterized by scanning electron microscopy, energy-dispersive spectroscopy, and wet chemical analysis using inductively coupled plasma optical emission spectrometry. The presence of solid spinel particles in the molten slag hindered coalescence and settling of matte/alloy droplets. Matte settling was effectively promoted with the addition of as little as 2wt% SPL because of the reduction of spinel by the carbonaceous component of the SPL. The reduced viscosity of the molten slag in the presence of SPL also contributed to the accelerated matte settling. Greater metal recoveries were achieved with larger amounts of added SPL. Fast reduction of the molten slag at 1573 K promoted the formation of highly dispersed metal particles/clusters via accelerated nucleation in the molten slag, which increased the overall slag viscosity. This increase in viscosity, when combined with rapid gas evolution from accelerated reduction reactions, led to slag foaming.     

Corrosion behavior of as-cast Mg–8Li–3Al+xCe alloy in 3.5wt% NaCl solution

Mg–8Li–3Al+xCe alloys (x = 0.5wt%, 1.0wt%, and 1.5wt%) were prepared through a casting route in an electric resistance furnace under a controlled atmosphere. The cast alloys were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The corrosion behavior of the as-cast Mg–8Li–3Al+xCe alloys were studied under salt spray tests in 3.5wt% NaCl solution at 35°C, in accordance with standard ASTM B–117, in conjunction with potentiodynamic polarization (PDP) tests. The results show that the addition of Ce to Mg–8Li–3Al (LA83) alloy results in the formation of Al₂Ce intermetallic phase, refines both the α-Mg phase and the Mg₁₇Al₁₂ intermetallic phase, and then increases the microhardness of the alloys. The results of PDP and salt spray tests reveal that an increase in Ce content to 1.5wt% decreases the corrosion rate. The best corrosion resistance is observed for the LA83 alloy sample with 1.0wt% Ce.     

In-situ fabrication of Al(Zn)-Al_2O_3 graded composite using the aluminothermic reaction during hot pressing

In this study, the fabrication of multilayer Al(Zn)–Al2 O3 with different volume fractions of Al2 O3 was investigated. Al and Zn O powders were milled by a planetary ball mill, after which five-layer functionally graded samples were produced through hot pressing at 580°C and 90 MPa pressure for 30 min. Formation of reinforcing Al2 O3 particles occurred in the aluminum matrix via the aluminothermic reaction. Determination of the ignition temperature of the aluminothermic reaction was accomplished using differential thermal and thermogravimetric analyses. Scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffractometery analyses were utilized to characterize the specimens. The thermal analysis results showed that the ignition temperatures for the aluminothermic reaction of layers with the highest and lowest Zn O contents were 667 and 670°C, respectively. Microstructural observation and chemical analysis confirmed the fabrication of Al(Zn)–Al2 O3 functionally graded materials composites with precipitation of additional Zn in the matrix. Moreover, nearly dense functionally graded samples demonstrated minimum and maximum hardness values of HV 75 and HV 130, respectively.     

Evolution of ferronickel particles during the reduction of low-grade saprolitic laterite nickel ore by coal in the temperature range of 900–1250℃ with the addition of CaO–CaF_2–H_3BO_3

The method of producing ferronickel at low temperature(1250–1400℃) has been applied since the 1950s at Nippon Yakin Kogyo,Oheyama Works, Japan.Limestone was used as an additive to adjust the slag composition for lowering the slag melting point.The ferronickel product was recovered by means of a magnetic separator from semi-molten slag and metal after water quenching.To increase the efficiency of magnetic separation, a large particle size of ferronickel is desired.Therefore, in this study, the influences of CaO, CaF_2, and H_3BO_3 additives on the evolution of ferronickel particle at ≤1250℃ were investigated.The experiments were conducted at 900–1250℃ with the addition of CaO,CaF_2, and H_3BO_3.The reduction processes were carried out in a horizontal tube furnace for 2 h under argon atmosphere.At 1250℃, with the CaO addition of 10 wt% of the ore weight, ferronickel particles with size of 20 μm were obtained.The ferronickel particle size increased to 165μm by adding 10 wt% CaO and 10 wt% CaF_2.The addition of boric acid further increased the ferronickel particle size to 376 μm, as shown by the experiments with the addition of 10 wt% CaO, 10 wt% CaF_2, and 10 wt% H_3BO_3.     

Effect of vanadium carbide on commercial pure aluminum

The effect of vanadium carbide (VC) on the grain size of commercial pure aluminum was experimentally investigated by varying the content of VC, the holding time, and casting temperature. The refining efficiencies of VC and Al5Ti1B were also compared. The refined samples of commercial pure aluminum were examined using optical microscopy, scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). The results suggest that VC is a good refiner of commercial pure aluminum. The addition of only 0.3wt% VC can decrease the grain size of aluminum to 102 μm, whereas the casting temperature and holding time have little effect on the grain size. The refining efficiency of VC is better than that of Al5Ti1B. The VC particles in molten aluminum act as nuclei and the grain refinement of aluminum alloys by VC particles is achieved via heterogeneous nucleation.     

High Temperature Corrosion of Fe-25Cr and Fe-17Cr-1.5Si-0.5Al Alloys in Oxidizing and Sulfidizing Enviornments

The simultaneous oxidation and sulfidation of Fe 25Cr and Fe-17Cr-l.5Si-0.5Al alloys was studied at 1023K and 1223K in H2-H2O-H2S gas mixtures. The kinetic boundary which indicates the transition from oxide to sulfide has heen found in these two alloys. The critical oxygen partial pressures of Fel7Crl.5SiO.5Al alloys were systematically lower than those of Fe-25Cr alloy. The reaction kinetics were measured by the stainless steel spring balance, and the reaction products were characterized by X-ray diffraction and scanning electron microscopy. The reaction rate usually decreased with the increase of the oxygen partial pressure at the constant sulfur partial pressure. The exista-nce of silicon plays an important role to suppress the sulfidation of Fel7Cr alloy.     

Thermal performance and reduction kinetic analysis of cold-bonded pellets with CO and H<Subscript>2</Subscript> mixtures

Cold-bonded pellets, to which a new type of inorganic binder was applied, were reduced by H₂–CO mixtures with different H₂/CO molar ratios (1:0, 5:2, 1:1, 2:5, and 0:1) under various temperatures (1023, 1123, 1223, 1323, and 1423 K) in a thermogravimetric analysis apparatus. The effects of gas composition, temperature, and binder ratio on the reduction process were studied, and the microstructure of reduced pellets was observed by scanning electron microscopy–energy-dispersive spectrometry (SEM-EDS). The SEM-EDS images show that binder particles exist in pellets in two forms, and the form that binder particles completely surround ore particles has a more significant hinder effect on the reduction. The reduction equilibrium constant, effective diffusion coefficient, and the reaction rate constant were calculated on the basis of the unreacted core model, and the promotion effect of temperature on reduction was further analyzed. The results show that no sintering phenomenon occurred at low temperatures and that the increasing reaction rate constant and high gas diffusion coefficient could maintain the promotion effect of temperature; however, when the sintering phenomenon occurs at high temperatures, gas diffusion is hindered and the promotion effect is diminished. The contribution of the overall equilibrium constant to the promotion effect depends on the gas composition.     

Thermal performance and reduction kinetic analysis of cold-bonded pellets with CO and H_2 mixtures

Cold-bonded pellets, to which a new type of inorganic binder was applied, were reduced by H2–CO mixtures with different H2/CO molar ratios(1:0, 5:2, 1:1, 2:5, and 0:1) under various temperatures(1023, 1123, 1223, 1323, and 1423 K) in a thermogravimetric analysis apparatus. The effects of gas composition, temperature, and binder ratio on the reduction process were studied, and the microstructure of reduced pellets was observed by scanning electron microscopy–energy-dispersive spectrometry(SEM-EDS). The SEM-EDS images show that binder particles exist in pellets in two forms, and the form that binder particles completely surround ore particles has a more significant hinder effect on the reduction. The reduction equilibrium constant, effective diffusion coefficient, and the reaction rate constant were calculated on the basis of the unreacted core model, and the promotion effect of temperature on reduction was further analyzed. The results show that no sintering phenomenon occurred at low temperatures and that the increasing reaction rate constant and high gas diffusion coefficient could maintain the promotion effect of temperature; however, when the sintering phenomenon occurs at high temperatures, gas diffusion is hindered and the promotion effect is diminished. The contribution of the overall equilibrium constant to the promotion effect depends on the gas composition.     

Comprehensive recovery of lead,zinc, and iron from hazardous jarosite residues using direct reduction followed by magnetic separation

Lead, zinc, and iron were recovered from jarosite residues using direct reduction followed by magnetic separation. The influence of the coal dosage, reduction temperature, and reduction time on the volatilization rates of lead and zinc and the metallization rate of iron were investigated. The results show that the volatilization rates of lead and zinc were 96.97% and 99.89%, respectively, and the iron metallization rate was 91.97% under the optimal reduction roasting conditions of a coal dosage of 25.0wt% and reduction roasting at 1250℃ for 60 min. The magnetic concentrate with an iron content of 90.59wt% and an iron recovery rate of 50.87% was obtained under the optimum conditions in which 96.56% of the reduction product particles were smaller than 37 μm and the magnetic field strength was 24 kA/m. Therefore, the results of this study demonstrate that recovering valuable metals such as lead, zinc, and iron from jarosite residues is feasible using the developed approach.     

Kinetic studies on the reduction of iron ore nuggets by devolatilization of lean-grade coal

An isothermal kinetic study of a novel technique for reducing agglomerated iron ore by volatiles released by pyrolysis of lean-grade non-coking coal was carried out at temperature from 1050 to 1200°C for 10–120 min. The reduced samples were characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and chemical analysis. A good degree of metallization and reduction was achieved. Gas diffusion through the solid was identified as the reaction-rate-controlling resistance; however, during the initial period, particularly at lower temperatures, resistance to interfacial chemical reaction was also significant, though not dominant. The apparent rate constant was observed to increase marginally with decreasing size of the particles constituting the nuggets. The apparent activation energy of reduction was estimated to be in the range from 49.640 to 51.220 kJ/mol and was not observed to be affected by the particle size. The sulfur and carbon contents in the reduced samples were also determined.     

Cu-Zn-Al2O3 nanocomposites:study of microstructure,corrosion,and wear properties

Alumina nanoparticles were added to a Cu-Zn alloy to investigate their effect on the microstructural, tribological, and corrosion properties of the prepared alloys. Alloying was performed using a mixture of copper and zinc powders with 0vol% and 5vol% of α-Al nanopowder in a satellite ball mill. The results showed that the Cu-Zn solid solution formed after 18 h of mechanical alloying. The mechanically alloyed powder was compacted followed by sintering of the obtained green compacts at 750℃ for 30 min. Alumina nanoparticles were uniformly distributed in the matrix of the Cu-Zn alloy. The tribological properties were evaluated by pin-on-disk wear tests, which revealed that, upon the addition of alumina nanoparticles, the coefficient of friction and the wear rate were reduced to 20% and 40%, respectively. The corrosion properties of the samples exposed to a 3.5wt% NaCl solution were studied using the immersion and potentiodynamic polarization methods, which revealed that the addition of alumina nanoparticles reduced the corrosion current of the nanocomposite by 90%.     

In situ reaction mechanism of MgAlON in Al–Al_2O_3–MgO composites at 1700°C under flowing N_2

The Al–Al_2O_3–MgO composites with added aluminum contents of approximately 0wt%, 5wt%, and 10wt%, named as M_1, M_2, and M_3, respectively, were prepared at 1700°C for 5 h under a flowing N_2 atmosphere using the reaction sintering method. After sintering, the Al–Al_2O_3–MgO composites were characterized and analyzed by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The results show that specimen M_1 was composed of MgO and MgAl_2O_4. Compared with specimen M_1, specimens M_2 and M_3 possessed MgAlON, and its production increased with increasing aluminum addition. Under an N_2 atmosphere, MgO, Al_2O_3, and Al in the matrix of specimens M_2 and M_3 reacted to form MgAlON and AlN-polytypoids, which combined the particles and the matrix together and imparted the Al–Al_2O_3–MgO composites with a dense structure. The mechanism of MgAlON synthesis is described as follows. Under an N_2 atmosphere, the partial pressure of oxygen is quite low; thus, when the Al–Al_2O_3–MgO composites were soaked at 580°C for an extended period, aluminum metal was transformed into AlN. With increasing temperature, Al_2O_3 diffused into AlN crystal lattices and formed AlN-polytypoids; however, MgO reacted with Al_2O_3 to form MgAl_2O_4. When the temperature was greater than(1640 ± 10)°C, AlN diffused into Al_2O_3 and formed spinel-structured AlON. In situ MgAlON was acquired through a solid-solution reaction between AlON and Mg Al_2O_4 at high temperatures because of their similar spinel structures.     

Effect of Al content on the reaction between Fe-10Mn-xAl(x=0.035wt%,0.5wt%,1wt%,and 2wt%)steel and CaO-SiO2-Al2O3-MgO slag

The effect of Al content(0.035 wt%,0.5 wt%,1 wt%,and 2 wt%)on the composition change of steel and slag as well as inclusion transformation of high manganese steel after it has equilibrated with Ca O-Si O₂-Al₂O₃-Mg O slag was studied using the method of slag/steel reaction.The experimental results showed that as the initial content of Al increased from 0.035 wt%to 2 wt%,Al gradually replaced Mn to react with Si O₂in slag to avoid the loss of Mn due to the reaction;this process caused both Al₂O₃in slag and Si in steel to increase while Si O₂and Mn O in slag to reduce.In addition,the type of inclusions also evolved as the initial Al content increased.The evolution route of inclusions was Mn O→Mn O-Al₂O₃-Mg O→Mg O→Mn O-Ca O-Al₂O₃-Mg O and Mn O-Ca O-Mg O.The shape of inclusions evolved from spherical to irregular,became faceted,and finally transformed to spherical.The average size of inclusions presented a trend that was increasing first and then decreasing.The transformation mechanism of inclusions was explored.As the initial content of Al increased,Mg and Ca were reduced from top slag into molten steel in sequence,which consequently caused the transformation of inclusions.     

Comprehensive recovery of lead,zinc, and iron from hazardous jarosite residues using direct reduction followed by magnetic separation

Lead, zinc, and iron were recovered from jarosite residues using direct reduction followed by magnetic separation. The influence of the coal dosage, reduction temperature, and reduction time on the volatilization rates of lead and zinc and the metallization rate of iron were investigated. The results show that the volatilization rates of lead and zinc were 96.97% and 99.89%, respectively, and the iron metallization rate was 91.97% under the optimal reduction roasting conditions of a coal dosage of 25.0 wt% and reduction roasting at 1250°C for 60 min. The magnetic concentrate with an iron content of 90.59 wt% and an iron recovery rate of 50.87% was obtained under the optimum conditions in which 96.56% of the reduction product particles were smaller than 37 μm and the magnetic field strength was 24 k A/m. Therefore, the results of this study demonstrate that recovering valuable metals such as lead, zinc, and iron from jarosite residues is feasible using the developed approach.     

Reduction in secondary dendrite arm spacing in cast eutectic Al-Si piston alloys by cerium addition

The effects of Ce on the secondary dendrite arm spacing (SDAS) and mechanical behavior of Al-Si-Cu-Mg alloys were investigated. The reduction of SDAS at different Ce concentrations was evaluated in a directional solidification experiment via computer-aided cooling curve thermal analysis (CA CCTA). -The results showed that 0.1wt%-1.0wt% Ce addition resulted in a rapid solidification time, △T_S, and low solidification temperature, △T_S, whereas 0.1wt% Ce resulted in a fast solidification time, △ta-Al, of the α-Al phase. Furthermore, Ce addition refined the SDAS, which was reduced to approximately 36%. The mechanical properties of the alloys with and without Ce were investigated using tensile and hardness tests. The quality index (Q) and ultimate tensile strength of (UTS) Al-Si-Cu-Mg alloys significantly improved with the addition of 0.1wt% Ce. Moreover, the base alloy hardness was improved with increasing Ce concentration.