Effect of Co addition on crystallization and magnetic properties of FeSiBPCu alloy

The effects of Co addition on the microstructure,crystallization processes and soft magnetic properties of(Fe1 xCox)83Si4B8P4Cu1(x?0.35,0.5,0.65)alloys were investigated.The experimental results demonstrated that the addition of Co decreased the thermal stability against crystallization of the amorphous phase,and thus improved the heat treatment temperature of this alloy.Fe Co Si BPCu nanocrystalline alloys with a dispersedα0-Fe Co phase were obtained by appropriately annealing the as-quenched ribbons at 763 K for 10 min.Theα0-Fe Co with grains size ranging from 9 to 28 nm was identified in primary crystallization.The coercivity(Hc)markedly increased with increasing x and exhibited a minimum value at x0.35,while the saturation magnetic flux density(Bs)shows a slight decrease.The(Fe0.65Co0.35)83Si4B8P4Cu1nanocrystalline alloy exhibited a high saturation magnetic flux density Bsof 1.68 T,a low coercivity,Hcof 5.4 A/m and a high effective permeability meof 29,000 at 1 k Hz.     

Corrosion study of resorbable Ca60Mg15Zn25 bulk metallic glasses in physiological fluids

The corrosion activity of amorphous plates of Ca_(60)Mg_(15)Zn_(25)alloy was investigated.The biocompatible elements were selected for the alloy composition.The electrochemical corrosion and immersion tests were carried out in a multi-electrolyte fluid and Ringer's solution.Better corrosion behavior was observed for the samples tested in a multi-electrolyte fluid despite the active dissolution of Ca and Mg in Ringer's solution.The experimental results indicated that reducing concentration of NaCl from 8.6 g/dm~3for Ringer's solution to 5.75 g/dm~3caused the decrease of the corrosion rate.The volume of the hydrogen evolved after 480 min in Ringer's solution(40.1 ml/cm~2)was higher in comparison with that obtained in a multi-electrolyte fluid(24.4 ml/cm~2).The values of opencircuit potential(E_(OCP))for the Ca_(60)Mg_(15)Zn_(25)glass after 1 h incubation in Ringer's solution and a multielectrolyte fluid were determined to be-1553 and-1536 m V vs.a saturated calomel electrode(SCE).The electrochemical measurements indicated a shift of the corrosion current density(j_(corr))from 1062μA/cm~2for the sample tested in Ringer's solution to 788μA/cm~2for the specimen immersed in a multi-electrolyte fluid.The corrosion products analysis was conducted by using the X-ray photoelectron spectroscopy(XPS).The corrosion products were identified to be CaCO_3,Mg(OH)_2,CaO,MgO and Zn O.The mechanism of corrosion process was proposed and described based on the microscopic observations.The X-ray diffraction and Fourier transform infrared spectroscopy(FTIR)also indicated that Ca(OH)_2,CaCO_3,Zn(OH)_2and Ca(Zn(OH)_3)_2·2H_2O mainly formed on the surface of the studied alloy.     

Hydrogen absorption properties of amorphous (Ni0.6Nb0.4−yTay)100−xZrx membranes

Ni based amorphous materials have great potential as hydrogen purification membranes. In the present work the melt spun(Ni_(0.6)Nb_(0.4-y)Ta_y)_(100-x)Zr_x with y=0, 0.1 and x=20, 30 was studied. The result of X-ray diffraction spectra of the ribbons showed an amorphous nature of the alloys. Heating these ribbons below T 400 °C, even in a hydrogen atmosphere(1-10 bar), the amorphous structure was retained. The crystallization process was characterized by differential thermal analysis and the activation energy of such process was obtained. The hydrogen absorption properties of the samples in their amorphous state were studied by the volumetric method,and the results showed that the addition of Ta did not significantly influence the absorption properties, a clear change of the hydrogen solubility was observed with the variation of the Zr content. The values of the hydrogenation enthalpy changed from ~37 k J/mol for x=30 to ~9 k J/mol for x=20. The analysis of the volumetric data provides the indications about the hydrogen occupation sites during hydrogenation, suggesting that at the beginning of the absorption process the deepest energy levels are occupied, while only shallower energy levels are available at higher hydrogen content, with the available interstitial sites forming a continuum of energy levels.     

Effect of pickling processes on the microstructure and properties of electroless Ni–P coating on Mg–7.5Li–2Zn–1Y alloy

The electroless plating Ni–P is prepared on the surface of Mg–7.5Li–2Zn–1Y alloys with different pickling processes.The microstructure and properties of Ni–P coating are investigated.The results show that the Ni–P coatings deposited using the different pickling processes have a different high phosphorus content amorphous Ni–P solid solution structure,and the Ni–P coatings exhibit higher hardness.There is higher phosphorus content of Ni–P amorphous coating using 125 g/L Cr O3and 110 ml/L HNO3(w68%)than using 180 g/L Cr O3and 1 g/L KF during pre-treatment,and the coating structure is more compact,and the Ni–P coatings exhibit more excellent adhesion with substrate(Fcup to22 N).The corrosion potential of Ni–P coating is improved and exhibits good corrosion resistance.As a result,Mg-7.5Li-2Zn-1Y alloy is remarkably protected by the Ni–P coating.     

Zr-pillared montmoril lonite supported cobalt nanoparticles for Fischer – Tropsch synthesis

In this article Fischer–Tropsch(FT) synthesis was studied over cobalt nanoparticles supported on modifed Montmorillonite(Zr-PILC).Co-loaded/Zr-PILC catalysts were synthesized by hydrothermal methods and were characterized by XRD,XRF,BET,H2-TPR,TGA and SEM techniques.FT reactions were carried out in fxed bed microreactor(T 225 1C,260 1C and 275 1C,P 1,5 and 10 bars).The FT-products obtained over Co-loaded/Zr-PILC catalysts showed increased selectivity of C2–C12hydrocarbons and decreased selectivity towards CH4and higher molecular weight hydrocarbons(C21) at a TOS of 2–30 h as compared to the Co-loaded/NaMMT catalysts.With increase in reaction temperature from225 1C to 275 1C,CO-conversion and CH4selectivity increases while that of C5+hydrocarbons decreases.Decrease in CH4selectivity while increase in C5+hydrocarbons and CO-conversion were observed on increasing the pressure of reaction.     

Synthesis, structure, and optical properties of manganese phthalocyanine thin films and nanostructures

Manganese phthalocyanine(MnPc) nanostructures with different morphologies were prepared on porous anodic alumina oxide(AAO) at different substrate temperature(T_S=50 ℃,80 ℃,120 ℃,180 ℃,240 ℃) in an organic molecular beam deposition(OMBD) system.The nanostructures morphologies were studied using scanning electron microscopy(SEM) and the results showed that the nanostructures morphologies could be modulated by the control of T_S,as a result,the continuous film was obtained at 50 ℃,whereas the nanorods(NRs),nanoribbons(NBs),nanowires(NWs),nanosheets(NSs) and nanoparticles(NPs) were facilely generated as T_S increased.At the same time,the density and the uniformity of the nanostructures decreased.The results of X-ray diffraction(XRD) indicated that only the(3-phase polymorph formed throughout the growth process irrelevant to the T_S.Additionally,the ultraviolet visible(UV-Vis) absorption spectra demonstrated that the main absorption bands of MnPc nanostructures showed a remarkable band broadening as the T_S was increased.     

Structure evolution of Y2O3 nanoparticle/Fe composite during mechanical milling and annealing

Fe-25 wt% Y2O3composite powders have been fabricated by mechanical milling(MM) Fe powders of 100 μm in diameter and Y2O3nanoparticles in an argon atmosphere for the milling periods of4,8,12,24,36,and 48 h,respectively.The features of these powders were characterized by using X-ray diffraction(XRD),scanning electron microscopy(SEM),electron probe micro analyzer(EPMA) and transmission electron microscopy(TEM).The experimental results showed that the mean particle size and crystalline size of MM powders decreased with the milling time increasing.All the elements distributed homogenously inside the powders after 48 h of MM.The lattice constant of the matrix α-Fe kept constant with the milling time,and no solid solution took place during MM process.After 8 h of MM,the α-Fe in each powder became nanocrystalline.After 48 h of MM,Y2O3changes from nanostructure into amorphous structure,and the crystalline size of α-Fe further decreased to 10 nm.The Y2O3in the powders mechanically milled for 48 h kept the amorphous structure after being annealed at 400 1C,and starts to crystallize when the powders are annealed at 600 1C.The amorphous Y2O3contains a small amount of Fe,and crystalline FeYO3appears at 800 1C.     

Effect of boehmite sol on the crystallization behavior and densification of mullite formed from a sol–gel precursor

Hybrid mullite sol was synthesized from an aqueous solution of aluminum nitrate (AN), aluminum isopropoxide (AIP) and tetraethylorthosilicate (TEOS), doped with boehmite sol with different ratios. Pressureless sintering of the xerogel was carried out at different temperatures in the presence of boehmite doping. The xerogel and sintered powder were characterized by FTIR, TG-DSC, XRD, SEM and bulk density. The addition of boehmite caused the formation of metaphase spinel (6Al2O3·SiO2) crystal before the appearance of mullite phase, which could lead to the formation of amorphous phase and suppress the premature formation of mullite. Both of these effects improve the densification of mullite. A maximum density about 98% of the theoretical density (TD, 3.01 g/cm3 ) of mullite could be obtained for 5 wt% boehmite addition at 1200 1C pressureless sintering.     

Wear properties of NiAl based materials

The NiAl based materials including NiAl-TiC-Al2O3 composite,NiAl-Cr(Mo)-Hf-Ho eutectic alloy and NiAl-Cr(Mo)-CrxSy in situ composite were fabricated and their wear properties were tested at different temperatures.The results revealed that the NiAl-TiC-Al2O3 composite,NiAl-Cr(Mo)-Hf-Ho eutectic alloy and NiAl-Cr(Mo)-CrxSy in situ composite exhibited the excellent wear properties between 700℃ and 900℃.The microstructure observations exhibited that the self-lubricant films formed on the worn surfaces during the dry sliding test at high temperature,which decreased the wear rate and friction coefficient significantly.TEM observation on the self-lubricant film revealed that it was mainly comprised by ceramic amorphous and nanocrystalline.Compared with the NiAl-TiC-Al2O3 composite,the NiAl-Cr(Mo)-CrxSy in situ composite has lower friction coefficient at low temperature.Such phenomena may be ascribed to the addition of sulfide which contributes much to the formation of self-lubricant,and moreover the TiC addition increase the strength of NiAl based material and its wear resistance.     

Phase analysis of AlFe2B2 by synchrotron X-ray diffraction, magnetic and Mössbauer studies

The structural and magnetic properties of essentially phase pure AlFe_2B_2 prepared by arc melting were compared with a sample containing impurities. Analysis was carried out by means of synchrotron X-ray diffraction, magnetic measurements and M?ssbauer spectroscopy. The analysis of synchrotron X-ray diffraction data confirmed the orthorhombic structure of space group Cmmm for AlFe_2B_2 with Al_(13)Fe_4 as main impurity phase. The magnetic measurements revealed an unsaturated ferromagnetic state in AlFe_2B_2 with a transition temperature(T_c) of 286 K. Isothermal magnetization measurment at 5 K gave a saturation magnetization of 0.7 μB per Fe atom while Arrott plots establish the second order nature of ferromagnetic transition. The thermal evolution of M?ssbauer spectra confirmed the ferromagnetic nature of this material revealing an hyperfine field of 73 kOe and an isomer shift of 0.46 mm/s at 100 K. The M?ssbauer spectra of a phase pure sample was compared with the one containing impurity phases. It is suggested that the low temperature paramagnetic contribution in M?ssbauer spectra of phase pure material may have its origin in some intrinsic phenomena arising from defects or inhomogeneities in crystal structure.     

The enhanced corrosion resistance of UMAO coatings on Mg by silane treatment

The surface silanization was carried out on ultrasonic micro-arc oxidation(UMAO) coatings on pure magnesium using KH550 as silane coupling agent(SCA). The surface morphology, chemical bonds and corrosion resistance of the silane films were investigated by scanning electron microscope(SEM), Fourier transform infrared spectroscopy(FTIR) and electrochemical workstation, respectively. The results showed that hybrid coatings were successfully prepared on pure magnesium by UMAO-Na OH(1 mol/L, 2 mol/L, 3 mol/L)-SCA processing. The organic films with Si–O–Mg bonds are helpful for the reduction of the pores in UMAO coatings. The pores decreased with increasing Na OH concentration. Compared with single UMAO treatment, the corrosion potentials(Ecorr) of magnesium plates with UMAO-Na OH(1 mol/L,2 mol/L, 3 mol/L)-SCA treatment increased by 29 m V, 53 m V and 75 m V, respectively, meanwhile the corrosion current density(Icorr) reduced one to two orders of magnitude. It indicated that the corrosion resistance of the coatings was improved by silane treatment.     

Composition design of superhigh strength maraging stainless steels using a cluster model

The composition characteristics of maraging stainless steels were studied in the present work investigation using a cluster-plus-glue-atom model. The least solubility limit of high-temperature austenite to form martensite in basic Fe–Ni–Cr corresponds to the cluster formula [NiFe12]Cr3,where NiFe12is a cuboctahedron centered by Ni and surrounded by 12 Fe atoms in FCC structure and Cr serves as glue atoms. A cluster formula [NiFe12](Cr2Ni) with surplus Ni was then determined to ensure the second phase(Ni3M) precipitation,based on which new multicomponent alloys [(Ni,Cu)16Fe192](Cr32(Ni,Mo,Ti,Nb,Al,V)16) were designed. These alloys were prepared by copper mould suction casting method,then solid-solution treated at 1273 K for 1 h followed by water-quenching,and finally aged at 783 K for 3 h. The experimental results showed that the multi-element alloying results in Ni3M precipitation on the martensite,which enhances the strengths of alloys sharply after ageing treatment. Among them,the aged [(Cu4Ni12)Fe192](Cr32(Ni8.5Mo2Ti2Nb0.5Al1V1)) alloy(Fe74.91Ni8.82Cr11.62Mo1.34Ti0.67Nb0.32Al0.19V0.36Cu1.78wt%) has higher tensile strengths with YS?1456 MPa and UTS?1494 MPa. It also exhibits good corrosion-resistance in 3.5 wt% NaCl solution.     

Synthesis of dental resins using diatomite and nano-sized SiO2 and TiO2

The mechanical properties of dental composites were improved by porous diatomite and nano-sized silica (OX-50) used as co-fillers.The resin composites,filled with silanized OX-50 and silanized diatomit...     

Properties of garnet-type Li6La3ZrTaO12 solid electrolyte films fabricated by aerosol deposition method

The garnet-type Li_6La_3ZrTaO_(12)(LLZT) solid electrolyte films were fabricated by aerosol deposition(AD)method.Ball-milled LLZT powder with a cubic garnet structure and a particle size of 1-2 urn was used as raw material and deposited directly on a SUS316L or a glass substrate via impact consolidation.As-deposited LLZT film has a cubic garnet structure but contains Li_2CO_3 and La_2Zr_2O_7 phases.SEM observation revealed that the film consists of LLZT particles fractured into submicron size.The impurity phase formation during AD process was caused by the local heating by the collision between LLZT particles and deposition surface and reaction with CO_2.The Li~+ ion conductivity of LLZT film was estimated to be 0.24 × 10~(-5)S cm~(-1) at room temperature.Electronic conductivity of LLZT film was confirmed to be around 10~(-12) S cm~(-1),indicating the dominant Li~+ ion conduction of LLZT film.     

Size-manipulat ion, compacti on and electrical properties of barium manganite nanorods synthesized via the CHM method

A composite-hydroxide mediated method was employed to synthesize barium manganite nanorods.Diameter,surface smoothness and uniformity of these nanorods were optimized by varying reaction temperature and reaction time.The rods with an average diameter of 200 nm and length of1–1.5 μm were obtained at optimum conditions of 200 1C/48 h.The dielectric study of these rods reveals that they have higher value of dielectric constant at lower frequencies which was attributed to the interfacial and rotational type polarizations.Similarly,the increase in dielectric constant with temperature was attributed to the thermal activation of such polarizations.Furthermore,the analysis of ln(J) vs.E1/2characteristics in the temperature range of 300–400 K shows that possible operative conduction mechanism was of Poole–Frenkel type.The value of βexp was found to be 4.85 times greater than the expected theoretical value of feld lowering coeffcient with an internal feld enhancement factor ofα2 23.5.This high value of βexp may be due to some localized electric felds existing inside the sample.     

A Ti–Zr–Cu–Ni–Co–Fe–Al–Sn amorphous filler metal for improving the strength of Ti–6Al–4V alloy brazing joint

Ti_(50)Zr_(27)Cu_8Ni_4Co_3Fe_2Al_3Sn_3(at%) amorphous filler metal with low Cu and Ni contents in a melt-spun ribbon form was developed for improving mechanical properties of Ti–6Al–4V alloy brazing joint through decreasing brittle intermetallics in the braze zone. Investigation on the crystallization behavior of the multicomponent Ti–Zr–Cu–Ni–Co–Fe–Al–Sn amorphous alloy indicates the high stability of the supercooled liquid against crystallization that favors the formation of amorphous structure. The Ti–6Al–4V joint brazed with this Ti-based amorphous filler metal with low total content of Cu and Ni at 1203K for 900s mainly consists of α-Ti, β-Ti,minor Ti–Zr-rich phase and only a small amount of Ti_3Cu intermetallics, leading to the high shear strength of the joint of about 460 MPa. Multicomponent composition design of amorphous alloys is an effective way of tailoring filler metals for improving the joint strength.     

Effect of CuO addition on the sintering temperature and microwave dielectric properties of CaSiO3– Al2O3 ceramics

CuO-doped CaSiO3–1 wt% Al2O3 ceramics were synthesized via a traditional solid-state reaction method, and their sintering behavior,microstructure and microwave dielectric properties were investigated. The results showed that appropriate CuO addition could accelerate the sintering process and assist the densification of CaSiO3–1 wt% Al2O3 ceramics, which could effectively lower the densification temperature from1250 1C to 1050 1C. However, the addition of CuO undermined the microwave dielectric properties. The optimal amount of CuO addition was found to be 0.8 wt%, and the derived CaSiO3–Al2O3ceramic sintered at 1100 1C presented good microwave dielectric properties of εr?7.27,Q f?16,850 GHz and τf? 39.53 ppm/1C, which is much better than those of pure CaSiO3 ceramic sintered at 1340oC(Q f?13,109 GHz).The chemical compatibility of the above ceramic with 30 Pd/70 Ag during the cofiring process has also been investigated, and the result showed that there was no chemical reaction between palladium–silver alloys and ceramics.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Thermal behavior of zirconia-dop ed mullite gel fibers

The zirconia-doped mullite gel fibers were prepared via a sol-gel method.The thermal behaviors of the gel fibers during pyrolysis were investigated by means of thermal gravitydifferential scanning calo...     

Preparation of Cu（In,Ga）Se2 thin film by sputtering from Cu（In,Ga）Se2 quaternary target

Cu(In,Ga)Se2 (CIGS) thin films were prepared by directly sputtering Cu(In,Ga)Se2 quaternary target consisting of Cu:In:Ga:Se 25:17.5:7.5:50 at%. The composition and structure of CIGS layers have been investigated after annealing at 550 ℃ under vacuum and a Se-containing atmosphere. The results show that recrystallization of the CIGS thin film occurs and a chalcopyrite structure with a preferred orientation in the (112) direction was obtained. The CIGS thin film annealed under vacuum exhibits a loss of a portion of Se, while the film annealed under Se-containing atmosphere reveals compensation of Se. Several solar cells with three different absorber thicknesses were fabricated using a soda lime glass/Mo/CIGS/CdS/i-ZnO/ZnO:Al/Al grid stack structure. The highest conversion efficiency of 9.65% with an open circuit voltage of 452.42 mV, short circuit current density of 32.16 mA cm2 and fill factor of 66.32% was obtained on a 0.755 cm2 cell area.     

Microstructure, mechanical and thermo-physical properties of hot-pressed Al2O3-GdAlO3-ZrO2 ceramics with eutectic composition

A low cost chemical co-precipitation method was employed to fabricate nanoscale Al_2O_3-GdAlO_3-ZrO_2 powder with eutectic composition. A careful control of reaction conditions was required during the preparation. The synthesized nanopowders exhibited a particle size of 20-200 nm, and were highly dispersive and uniform. The results showed that calcination temperature had an important influence on the phase constituents of the nanopowders. With increasing the calcination temperature, a phase transformation from θ-Al_2O_3 to α-Al_2O_3 and a thermal decomposition from Gd_3 Al_5O_(12)(GdAG) to GdAlO_3 and α-Al_2O_3 occurred in sequence. A calcination temperature of 1300 ℃ was needed for the crystallization of α-Al_2 O_3. These nanosized powders were consolidated via hot pressing to produce a fully densified ceramic composite with eutectic composition. The Al_2O_3-GdAlO_3-ZrO_2 ceramic hot-pressed at 1500 ℃ exhibited a relative density of 99.4%, a flexural strength of 485 MPa and a fracture toughness of 6.5 MPa m~(1/2). The ceramic had a thermal conductivity of 1.9 W m K~(-1) at 1200 ℃ and a thermal expansion coefficient of 9.49 ×10~(-6) K~(-1) at 1100 ℃.