Microstructure and properties of A2017 alloy strips processed by a novel process by combining semisolid rolling, deep rolling, and heat treatment

A novel short process for producing A2017 alloy strips with notable features of near net shape, saving energy, low cost, and high product performance was developed by combining semisolid rolling, deep rolling, and heat treatment. The microstructure and properties of the A2017 alloy strips were investigated by metallographic microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, tensile testing, and hardness measurement. The cross-sectional microstructure of the A2017 alloy strips is mainly composed of near-spherical primary grains. Many eutectic phases CuAl₂ formed along primary grain boundaries during semisolid rolling are crushed and broken into small particles. After solution treatment at 495℃ for 2 h the eutectic phases at grain boundaries have almost dissolved into the matrix. When the solution treatment time exceeds 2 h, grain coarsening happens. More and more grain interior phases precipitate with the aging time prolonging to 8 h. The precipitated particles are very small and distribute homogenously, and the tensile strength reaches its peak value. When the aging time is prolonged to 12 h, there is no obvious variation in the amount of precipitated phases, but the size and spacing of precipitated phases increase. The tensile strength of the A2017 alloy strips produced by the present method can reach 362.78 MPa, which is higher than that of the strips in the national standard of China.     

Microstruct ural evolution and mechanical behavior of metastable β -type Ti – 25Nb–2Mo – 4Sn alloy with high strength and low modulus

This paper presents a systematic study of newly developed metastable β-type Ti-25Nb-2Mo-4Sn (wt%) alloy with high strength and low elastic modulus, with focus on the microstructural evolution and mechanical behavior associated with aging. The pre-treatment (solution treatment or cold rolling) prior to aging exerts substantial influence on the subsequent aging response including microstructural evolution and mechanical behavior. Even under the same aging treatment, the aging products could be (β+ω), or alternatively (β+α), depending on the pre-treatments. This interesting aging response was discussed on the basis of the mechanism for ω formation. High-density dislocation tangles and grain boundaries induced by severe cold rolling play a key role in hindering the transition from β to isothermal ω, favoring the precipitation of α phase on aging. By aging cold-rolled specimen for short time, superior mechanical properties, i.e. high ultimate strength of ～1113 MPa and low elastic modulus of ～65 GPa, achieved in Ti-25Nb-2Mo-4Sn alloy. The characterization of microstructural evolution and compositional change indicated that the precipitation of fine α does not cause the enrichment of β-stabilizers in β matrix upon a short-time aging, guaranteeing low elastic modulus of the short-time aged specimen. Meanwhile, fine α precipitates as well as dislocations play a crucial part in strengthening, giving rise to its high yield strength and high ultimate tensile strength.     

Microstructure and mechanical properties of cryorolled AZ31 magnesium alloy sheets with different initial textures

AZ31 magnesium alloy sheets with different strong textures were cryorolled at the liquid-nitrogen temperature to the strain of 4% and 8%. The microstructure and texture of the rolled sheets were investigated via scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and X-ray diffraction (XRD). The mechanical properties of the sheets were tested through in-plane uniaxial tensile tests at ambient temperature. The tensile stress was exerted in the rolling direction (RD) and transverse directions (TD). The microstructural and textural evolutions of the alloy during cryorolling were investigated. Due to active twining during rolling, the initial texture significantly influenced the microstructural and textural evolutions of the rolled sheets. A {1012} extension twin was found as the dominated twin-type in the cryorolled samples. After cryogenic rolling, the ductility of the samples decreased while the strength increased. Twinning also played an important role in explaining the mechanical differences between the rolled samples with different initial textures. The samples were significantly strengthened by the high stored energy accumulated from cryorolling.     

Effect of particle size distribution on the microstructure,texture,and mechanical properties of Al–Mg–Si–Cu alloy

The effect of particle size distribution on the microstructure,texture,and mechanical properties of Al–Mg–Si–Cu alloy was investigated on the basis of the mechanical properties,microstructure,and texture of the alloy.The results show that the particle size distribution influences the microstructure and the final mechanical properties but only slightly influences the recrystallization texture.After the pre-aging treatment and natural aging treatment(T4 P treatment),in contrast to the sheet with a uniform particle size distribution,the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids exhibits higher strength and a somewhat lower plastic strain ratio(r) and strain hardening exponent(n).After solution treatment,the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids possesses a finer and slightly elongated grain structure compared with the sheet with a uniform particle size distribution.Additionally,they possess almost identical weak recrystallization textures,and their textures are dominated by CubeND {001}310 and P {011}122 orientations.     

Effects of Calcium and Yttrium on Microstructure and Mechanical Properties of High Strain-Rate Rolled AZ91D Magnesium Alloy

Effects of calcium( Ca) and yttrium( Y) on microstructure and mechanical properties of high strain-rate rolled AZ91 D magnesium alloy were studied. High strain-rate rolling can improve the strength and plasticity of magnesium alloy sheets.Additions of Ca and Y into AZ91 D can refine grains and modify the size and the distribution of the precipitated phases. After solution treatment( 418 ℃ and 20 h) and high strain-rate rolling( heating at420 ℃ for 10 min firstly and then rolling from 10 mm to 2 mm in thickness via a single pass),the tensile strength of the AZ91 D-0. 2%Ca alloy was 1. 3% higher than that of the AZ91 D-0. 4 D%Y alloy,and the tensile strength of the AZ91 D-0. 2%Ca-0. 4%Y alloy was about 8. 3% and 6. 9% higher than those of the AZ91 D-0. 4%Y and the AZ91 D-0. 2%Ca alloys respectively.     

Effect of particle size distribution on the microstructure,texture, and mechanical properties of Al–Mg–Si–Cu alloy

The effect of particle size distribution on the microstructure, texture, and mechanical properties of Al–Mg–Si–Cu alloy was investigated on the basis of the mechanical properties, microstructure, and texture of the alloy. The results show that the particle size distribution influences the microstructure and the final mechanical properties but only slightly influences the recrystallization texture. After the pre-aging treatment and natural aging treatment (T4P treatment), in contrast to the sheet with a uniform particle size distribution, the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids exhibits higher strength and a somewhat lower plastic strain ratio (r) and strain hardening exponent (n). After solution treatment, the sheet with a bimodal particle size distribution of large constituent particles and small dispersoids possesses a finer and slightly elongated grain structure compared with the sheet with a uniform particle size distribution. Additionally, they possess almost identical weak recrystallization textures, and their textures are dominated by CubeND {001}<310> and P {011}<122> orientations.     

Effects of aging treatment and heat input on the microstructures and mechanical properties of TIG-welded 6061-T6 alloy joints

Aging treatment and various heat input conditions were adopted to investigate the microstructural evolution and mechanical properties of TIG welded 6061-T6 alloy joints by microstructural observations, microhardness tests, and tensile tests. With an increase in heat input, the width of the heat-affected zone (HAZ) increases and grains in the fusion zone (FZ) coarsen. Moreover, the hardness of the HAZ decreases, whereas that of the FZ decreases initially and then increases with an increase in heat input. Low heat input results in the low ultimate tensile strength of the welded joints due to the presence of partial penetrations and pores in the welded joints. After a simple artificial aging treatment at 175℃ for 8 h, the microstructure of the welded joints changes slightly. The mechanical properties of the welded joints enhance significantly after the aging process as few precipitates distribute in the welded seam.     

Preparation of high-strength Al-Mg-Si-Cu-Fe alloy via heat treatment and rolling

An Al-Mg-Si-Cu-Fe alloy was solid-solution treated at 560°C for 3 h and then cooled by water quenching or furnace cooling. The alloy samples which underwent cooling by these two methods were rolled at different temperatures. The microstructure and mechanical properties of the rolled alloys were investigated by optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction analysis, and tensile testing. For the water-quenched alloys, the peak tensile strength and elongation occurred at a rolling temperature of 180°C. For the furnace-cooled alloys, the tensile strength decreased initially, until the rolling temperature of 420°C, and then increased; the elongation increased consistently with increasing rolling temperature. The effects of grain boundary hardening and dislocation hardening on the mechanical properties of these rolled alloys decreased with increases in rolling temperature. The mechanical properties of the 180°C rolling water-quenched alloy were also improved by the presence of β″ phase. Above 420°C, the effect of solid-solution hardening on the mechanical properties of the rolled alloys increased with increases in rolling temperature.     

A β-type TiNbZr alloy with low modulus and high strength for biomedical applications

The effect of thermo-mechanical treatment on the mechanical properties of a novel β-type Ti–36Nb–5Zr(wt%) alloy has been investigated.The solution treated alloy consists of β and α″ phases and exhibits a two-stage yielding with a low yield stress(around 100 MPa). After cold rolling at a reduction of 87.5% and subsequent annealing treatment at 698 K for 25 min, a fine microstructure with nanosized α precipitates distributed in small β grains as well as high density of dislocations was obtained to achieve a yield strength of 720 MPa and a ultimate tensile strength of 860 MPa. In spite of the formation of α precipitates, the β-stabilizers are not enriched in the parent β matrix due to the short duration and low temperature of the thermal treatment, resulting in a low chemical stability of β phase. The low stability of β phase and the small volume fraction of α precipitates produce a low Young’s modulus of 48 GPa. Such an excellent combination of low elastic modulus and high strength in mechanical properties indicates great potential for biomedical applications.     

Effect of equal channel angular pressing on aging treatment of Al-7075 alloy

The effect of aging treatment on microstructure and mechanical properties of equal channel angular pressed Al-7075 alloy was examined.Commercial Al-7075 alloy in the solid solution heat-treated condition was processed by equal channel angular pressing through route BCat both the room temperature and 120 1C. Only three passes of equal channel angular pressing was possible due to the low ductility of the alloy at both temperatures. Followed by equal channel angular pressing, the specimens have been aged at 120 1C for different aging times. Mechanical properties were measured by Vickers microhardness and tensile tests and microstructural observations were undertaken using transmission electron microscopy, X-ray diffractometer as well as optical microscopy. Microstructural investigations showed that ultrafine-grained materials with grain size in the range of 200–350 nm and 300–500 nm could be obtained after three passes of equal channel angular pressing at room temperature and 120 1C, respectively. Equal channel angular pressing of solid solution heat-treated Al-7075 alloy accelerates precipitation rate and subsequently leads to a significant decrease in aging time to attain maximum mechanical properties. Furthermore, it is possible to achieve maximum mechanical properties during equal channel angular pressing at 120 1C as a result of dynamic aging and formation of small η′ phase.     

Effects of heat treatment on the microstructure and mechanical properties of ZA84 magnesium alloy

The effects of heat treatment on the microstructure and mechanical properties of ZA84 (Mg-8Zn-4Al-0.25Mn) alloy were investigated. The results indicate that the as-cast microstructure of the alloy is mainly composed of α-Mg matrix and two different morphologies of precipitates (continuous and quasi-continuous Mg₃₂(Al,Zn)₄₉ phases and isolated Mg₅Al₂Zn₂ phases). After solid solution treatment at 345℃, the Mg₃₂(Al,Zn)₄₉ phases change from continuous and quasi-continuous net to disconnected acute angle shape, and parts of second phases sphericize. The optimum heat treatment condition for the alloy is solution treatment at 345℃ for 48 h and water quenching, then aging treatment at 200℃ for 12 h and atmosphere cooling. Under the optimum condition, the ultimate tensile strength and yield strength of the alloy can be imoroved, but the elongation is not effected much bv heat treatment.     

Effects of cold rolling on the microstructure and mechanical properties of Fe-Ni-Mn-Mo-Ti-Cr maraging steels

Effects of cold rolling on the microstructure and mechanical properties of Fe-Ni-Mn-Mo-Ti-Cr maraging steels were studied. To investigate the microstructure and mechanical properties, optical microscopy, scanning electron microscopy, X-ray diffraction, tensile test, and hardness test were used. The results show that the solution-annealing treatment in the cold-rolled steel redounds to the formation of submicrocrystalline Fe₂(Mo, Ti) Laves phase particles, which are stable at high temperatures. These secondary Laves phase particles prevent from recrystallization at high temperatures and correspond to semi-brittle fracture in the subsequent aging treatment.     

Influence of ECAP on the fatigue behavior of age-hardenable 2xxx aluminum alloy

The fatigue behavior under load control and the mechanical properties of commercial 2011 aluminum as an age-hardenable Al alloy was studied. To estimate the effects of the equal channel angular pressing (ECAP) process, solution heat treatments, and aging on the fatigue life, tests were conducted at four different stages:furnace cooling; furnace cooling plus one ECAP pass; solid solution heat treatment, quenching, one ECAP pass plus aging at peak age level; and the T6 condition. Only one pass was possible at room temperature because of the high strength of the material. The fracture surface morphology and microstructure after fatigue were evaluated by scanning electron microscopy (SEM). The experimental results revealed that the optimum fatigue life under load control, the tensile strength, and the Vickers hardness of the material were interdependent. The optimum fatigue life under load control was achieved by increasing the tensile strength and hardness of the material.     

Effects of conform continuous extrusion and heat treatment on the microstructure and mechanical properties of Al-13Si-7.5Cu-1Mg alloy

The effects of conform continuous extrusion and subsequent heat treatment on the mechanical and wear-resistance properties of high-alloying Al-13Si-7.5Cu-1Mg alloy were investigated. The microstructures of alloys before and after conform processing and aging were compared by transmission electron microscopy and scanning electron microscopy, respectively. The results reveal that the primary phases were broken and refined by intense shear deformation during conform processing. After the conform-prepared Al-13Si-7.5Cu-1Mg alloy was subjected to solid-solution treatment at 494℃ for 1.5 h and aging at 180℃ for 4 h, its hardness improved from HBS 115.8 to HBS 152.5 and its ultimate tensile strength increased from 112.6 to 486.8 MPa. Its wear resistance was also enhanced. The factors leading to the enhanced strength, hardness, and wear resistance of the alloy were discussed in detail.     

热轧和退火温度对SP-700合金组织和力学性能的影响

The effect of rolling temperature on both two- and single-phase regions and annealing in a temperature range of 700–950°C on the microstructure and mechanical properties of Ti?5Al?4V?2Fe?1Mo alloy was investigated. The results indicated that the best balance of strength and ductility is obtained by rolling in the two-phase region due to the globularization of the alpha phase and increase in its volume fraction. After rolling in the two-phase region, the ductility of the specimens annealed at 700 to 800°C increased because of the finer size and globularized alpha phase, while the reduction in strength was attributed to a decrease in the alpha phase volume fraction. However, at 950°C, the strength increased and ductility dropped by the formation of acicular alpha phase due to an increase in the phase boundary area. Annealing and aging after rolling in the beta-phase region increased the strength and decreased the ductility, which is attributed to the formation of a secondary alpha phase. A combination of favorable yield strength (1113 MPa) and elongation (13.3%) was obtained through rolling at 850°C followed by annealing at 750°C and aging at 570°C.     

Effect of rolling geometry on the mechanical properties,microstructure and recrystallization texture of Al-Mg-Si alloys

The effect of rolling geometry on mechanical properties, microstructure, and recrystallization texture of Al-Mg-Si alloys was studied by means of tensile tests, microstructural observations, and electron backscatter diffraction measurements. The results reveal that the elongation and the average plasticity strain ratio (r) values of the T4P (pre-aging plus natural aging)-treated alloy sheet with a rolling geometry value between 1 and 3 are somewhat higher than those of the T4P-treated sheet with a rolling geometry value between 3 and 6. The deformation and recrystallization microstructures of the sheet with a rolling geometry value between 1 and 3 are more uniform than those of the sheet with a rolling geometry value between 3 and 6. The former also possesses somewhat higher surface quality. H {001}〈110〉 and Goss {110}〈001〉 orientations are the main recrystallization texture components for the former case, whereas the latter case only includes H{001}〈110〉 orientation. Texture gradients are present in the two alloy sheets. Shear texture component F on the surface of the sheet with a rolling geometry value between 3 and 6 and its higher texture gradients have revealed that non-uniform deformation occurred during cold rolling. The effects of texture on the yield strength and r value were also discussed.     

Structure and properties of an ultra-high strength 7xxx aluminum alloy contained Sc and Zr

An ultra-high strength aluminum alloy was produced by casting and then extruded to rods. The effect of heat treatment on the microstructure and mechanical properties of the alloy was investigated. After single ageing (120℃, 24 h), the tensile strength was 812.4 MPa and the elongation was 6.2%. After retrogression reaging (RRA), the tensile strength was 751.2 MPa and the elongation was 6.4%. The strengthening mechanism is considered as fine grain strengthening, substructure strengthening and dispersion strengthening by Al₃(Sc, Zr).     

Effect of hot rolling and annealing temperatures on the microstructure and mechanical properties of SP-700 alloy

The effect of rolling temperature on both two-and single-phase regions and annealing in a temperature range of 700–950°C on the microstructure and mechanical properties of Ti-5 Al-4 V-2 Fe-1 Mo alloy was investigated. The results indicated that the best balance of strength and ductility is obtained by rolling in the two-phase region due to the globularization of the alpha phase and increase in its volume fraction. After rolling in the two-phase region, the ductility of the specimens annealed at 700 to 800°C increased because of the finer size and globularized alpha phase, while the reduction in strength was attributed to a decrease in the alpha phase volume fraction. However, at 950°C, the strength increased and ductility dropped by the formation of acicular alpha phase due to an increase in the phase boundary area. Annealing and aging after rolling in the beta-phase region increased the strength and decreased the ductility, which is attributed to the formation of a secondary alpha phase. A combination of favorable yield strength(1113 MPa) and elongation(13.3%) was obtained through rolling at 850°C followed by annealing at 750°C and aging at 570°C.     

Influence of multi-stage heat treatment on the microstructure and mechanical properties of TC21 titanium alloy

Duplex-structured TC21 alloy samples were first solution-treated at a higher temperature in the α + β region(940°C) with furnace cooling(FC), air cooling(AC), and water cooling(WC), followed by a second-stage solution treatment at a lower temperature in the α + β region(900°C), and then finally aged at 590°C. The effects of the morphology and quantity of α phases on the structure and properties of the TC21 alloy after the different heat treatments were analyzed. The in-situ tensile deformation process and crack propagation behavior were observed using scanning electron microscopy(SEM). The quantity of equiaxed α phases as well as the thickness of lamellar α phases reduced, the tensile strength increased firstly and then decreased, the elongation decreased with the increasing cooling rate after the first-stage solution treatment. The amount and size of lamellar α phases increased after the second-stage solution treatment because of sufficient diffusion of the alloying elements, thereby leading to increased tensile strength. The amount of dispersed α phases increased after the third-stage aging treatment owing to the increase in the nucleation rate, resulting in a noteworthy strengthening effect. After the third-stage aging treatment, the first-stage FC sample exhibited better mechanical properties because it contained more equiaxed α and βtrans phases than the first-stage AC and WC samples.     

多级热处理对TC21钛合金组织和力学性能的影响

Duplex-structured TC21 alloy samples were first solution-treated at a higher temperature in the α + β region (940°C) with furnace cooling (FC), air cooling (AC), and water cooling (WC), followed by a second-stage solution treatment at a lower temperature in the α + β region (900°C), and then finally aged at 590°C. The effects of the morphology and quantity of α phases on the structure and properties of the TC21 alloy after the different heat treatments were analyzed. The in-situ tensile deformation process and crack propagation behavior were observed using scanning electron microscopy (SEM). The quantity of equiaxed α phases as well as the thickness of lamellar α phases reduced, the tensile strength increased firstly and then decreased, the elongation decreased with the increasing cooling rate after the first-stage solution treatment. The amount and size of lamellar α phases increased after the second-stage solution treatment because of sufficient diffusion of the alloying elements, thereby leading to increased tensile strength. The amount of dispersed α phases increased after the third-stage aging treatment owing to the increase in the nucleation rate, resulting in a noteworthy strengthening effect. After the third-stage aging treatment, the first-stage FC sample exhibited better mechanical properties because it contained more equiaxed α and β_trans phases than the first-stage AC and WC samples.