一体式膜生物反应器处理中药废水的试验研究

针对中药废水具有COD高,水质变化大等特点,采用一体式膜生物反应器(MBR)对中药废水的厌氧反应器出水进行处理,在固定水力停留时间(HRT)为5 h的条件下,考察了进水COD质量浓度及污泥质量浓度(MLSS)与COD去除之间的关系.结果表明,当HRT为5 h,进水COD质量浓度小于3 000 mg/L时,膜出水COD小于30 mg/L,满足中水回用标准;当进水COD质量浓度为3 000～6 000 mg/L时,膜出水COD大于30 mg/L而小于100 mg/L,满足污水排放标准;当进水COD质量浓度大于6 000 mg/L,膜出水COD大于100 mg/L,不能满足污水排放标准.同时污泥质量浓度(MLSS)与COD去除的关系表明,为了达到更好的COD去除率,MBR的最佳MLSS应控制在7 543 mg/L.     

膜-好氧组合工艺处理餐饮废水的研究

采用无机膜－好氧组合工艺对高浓度餐饮废水（COD15000mg/L)进行处理，考察进水COD浓度，溶解氧浓度，水力停留时间对好氧反应器处理效果的影响，结果表明，当水力停留时间大于5．6h时，废水的COD去除率高于90％，温度对处理效果影响不大。对好氧出水用无机膜进行分离，最终出水COD小于25mg/L，浊度小于1NTU。     

曝气生物滤池及其填料性能

为提高曝气生物滤池(BAF)处理废水的效率,以沸石、活性炭、建筑陶粒、工程陶粒作为填料测试气体流速、水力停留时间(HRT)、进水有机负荷对生物滤池的化学需氧量(COD)、NH3—N的去除效果及出水浊度的影响。结果表明:在水力停留时间为1.5h、进水COD为150mg/L、有机负荷为2.41kgCOD/(m3·d)时,两种陶粒出水COD均小于25mg/L;当进水有机负荷为0.74kgCOD/(m3·d)时,工程陶粒出水COD小于10mg/L;工程陶粒是曝气生物滤池填料的最佳选择。     

红霉素生产废水处理试验研究

利用UASB反应器处理红霉素废水试验运行结果表明:通过控制进水中COD浓度和对厌氧污泥有效的培养驯化,红霉素生产废水可以被有效处理,进水COD为6700-7500mg/L,出水COD为820-1000mg/L,反应器水力停留时间25h,容积负荷达到3-4.5kgCOD/(m3.d),COD去除率达到88%.     

UBF-砂滤工艺处理城市污水实验研究

采用UBF-砂滤工艺处理城市污水,成功地进行污泥颗粒化.在进水COD为150-600mg L,自然室温为26-30℃,水力停留时间为8h时,UBF-砂滤系统出水COD浓度小于60mg L,pH值接近7.     

ABR-生物接触氧化工艺处理低碳氮比污水的碳源调配

低碳氮比生活污水由于碳源不足,采用传统A/O工艺处理难以出水达标.采用改进的ABR-生物接触氧化工艺对低碳氮比污水进行实验,通过优化运行参数,合理调配碳源,提高碳源利用率,确定了不同m(COD)/m(N)条件下该工艺对污水的处理效果.研究结果表明:改进的ABR-生物接触氧化工艺能有效提高碳源利用率和脱氮效率;在水力停留时间为10h,混合液回流比为2.5,温度为30℃时,系统碳源利用率和TN去除率达到最高;在不同m(COD)/m(N)条件下,TN去除率随着m(COD)/m(N)的减小而迅速降低.当进水m(COD)/m(N)为2～4时,TN去除率低于60％,处理效果不理想:当进水m(COD)/m(N)约为5时,TN去除率达到71.3％,出水TN质量浓度小于20 mg/L,满足排放标准要求;当m(COD)/m(N)为6～7时,TN去除率大于80％,出水TN质量浓度小于15 mg/L.     

高pH值条件下ABR工艺处理印染废水中试试验研究

对厌氧折流板反应器(ABR)处理难降解印染废水进行中试研究.结果表明,ABR反应器可以控制的水力停留时间(HRT)较短(11~12 h),承受的pH值范围较广(6.5~10.3).在进水COD、BOD质量浓度波动较大(700~1 500 mg/L,300~700 mg/L),高进水pH值,低HRT的情况下,ABR对COD、BOD的平均去除率分别为30%和15%,印染废水的BOD/COD由0.52提高到0.65,废水可生化性明显改善.     

海绵铁微电解法去除生活污水中COD的研究

采用单因素法对海绵铁微电解法去除生活污水中COD过程中5个工艺参数(水力停留时间、进水COD浓度、进水pH值、海绵铁投加量)的影响进行了研究;在此基础上,进行了5水平、6因素的正交试验,得到最佳反应条件为:反应时间5min、pH值2、海绵铁投加量5g/L、进水COD浓度200mg/L时,COD去除率为45.3%,达到城市污水作为预处理阶段的目的。     

好氧颗粒污泥膜生物反应器处理畜禽废水

采用好氧颗粒污泥膜生物反应器处理畜禽废水,分别对COD、NH4 -N、NO2--N、NO3--N的去除效果和对膜通量的影响进行了研究。结果表明:在水力停留时间(HRT)为8h,进水COD浓度为600mg/L,NH4 -N浓度为40mg/L的条件下,出水COD、NH4 -N的浓度分别为46.6和4.8mg/L。NO2--N和NO3--N的去除率也可达90%以上。并且好氧颗粒污泥的加入减缓了膜的污染。     

复合式折流板厌氧反应器处理城市污水

采用弹性立体填料的复合式折流板厌氧反应器处理城市污水 .研究结果表明 ,该装置处理城市污水效果显著 .当进水COD在 87- 32 0mg L范围内 (平均 2 2 7mg L)变化 ,水力停留时间大于 5 .2h ,反应系统的容积负荷小于 0 .86kgCOD (m3·d)时 ,常温下COD去除率大于 6 0 % ,出水COD平均为 81mg L ,SS去除率大于77.8% ,出水SS小于 30mg L ;反应系统在试验条件下温度与溶解性COD去除率成正相关 .试验还得出了系统处理城市污水溶解性BOD去除率随HRT变化的降解动力学模式 .     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

Perspherical Approaches for Electrons in Atoms and Charged Excitons in Quantum Wells

Instead of following Fock’s expansion,we solve the Schrodinger equation for some quantum mechanical manybody systems such as electrons in atoms and charged excitons in quantum wells in a similar way in hyperspherical coordinates by expanding the wave functions into orthonormal complete basis sets of the hyperspherical hannonics(HHs)of hyperangles and generalized Laguerre polynomials(GLPs)of the hyperradius.This leads the equation to     

Advances in broadband wireless communications under high-mobility scenarios

Future mobile communication systems aim at providing very high data transmission rates, even in high-mobility scenarios such as high-speed wheel-track trains, maglev trains, highway vehicles, airplanes, guided missiles or spacecraft. A particularly important commercial application is the strong and increasing worldwide demand for high- speed broadband wireless communications （up to 574.8 km/ h test speeds or 380 km/h commercial speeds） in railways, providing data, voice and video services for applications such as onboard entertainment services to passengers, train control, train dispatch, train sensor status handling and sur- veillance. In such high-mobility scenarios, there are a number of communication challenges, including fast hand- over, location updating, high-speed channel modeling, estimation and equalization, anti-Doppler spreading tech- niques, fast power control, and dedicated network architec- ture. Because signal transmission in very high-speed scenarios will inevitably experience serious deterioration, it is imperative to develop key broadband mobile communi- cation techniques for such high-speed vehicles.     

Wuhan University Journal of Natural Sciences TOTAL CONTENTS

<正>~~     

Scale-based spatial data model for GIS

Being the primary media of geographical information and the elementary objects manipulated, almost all of maps adopt the layer-based model to represent geographic information in the existent GIS. However, it is difficult to extend the map represented in layer-based model. Furthermore, in Web-Based GIS, It is slow to transmit the spatial data for map viewing. In this paper, for solving the questions above, we have proposed a new method for representing the spatial data. That is scale-based model. In this model we represent maps in three levels: scale-view, block, and spatial object, and organize the maps in a set of map layers, named Scale-View, which associates some given scales.Lastly, a prototype Web-Based GIS using the proposed spatial data representation is described briefly.     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to