纳米钨粉的烧结工艺

采用催化-凝胶法制备的平均粒径60nm的纳米钨粉为原料,经钢模压制成生坯,用高温膨胀仪测定了纳米钨粉坯体的烧结收缩动力学曲线;然后分别测定了不同烧结温度和烧结时间下烧结体晶粒尺寸和相对密度的变化.结果表明,纳米钨粉的坯体在200℃开始收缩,1300℃基本停止收缩.从1000℃到1200℃,其相对密度提高了24%,是致密化过程最快的阶段.在1200℃×120min的烧结工艺下得到烧结体相对密度为95%,晶粒尺寸为5μm的钨材.     

B_4C粉末的气流粉碎及烧结

采用气流粉碎对B4C粗粉 (比表面积为 0 5 2m2 g,中位粒度为 2 0 4μm)进行粉碎实验 ,研究了气流粉碎次数对粉末性能、压坯密度和烧结密度的影响及成形压力和烧结温度对B4C烧结密度的影响 .研究结果表明 :当粉碎次数达到 3次后 ,可获得中位粒度小于 1μm的B4C超细粉末 ;经过 4次气流粉碎的B4C超细粉末 ,其比表面积为2 5 3m2 g ,中位粒度为 0 5 6 μm ;该粉末于 2 2 5 0℃无压烧结 1h ,其烧结密度为 2 0 7g cm3 ,达到理论密度的82 .5 % ,平均晶粒粒度为 5 0 μm .可见 ,气流粉碎能改善B4C的烧结性 .     

烧结压力对铜粉放电等离子烧结的影响规律

研究了平均粉末粒度为1μm的铜粉在不同压力条件下的放电等离子烧结过程,系统分析了压坯的密度和微观组织与烧结升温阶段的初始压力和保压压力之间的关系. 结果表明:烧结温度为800℃,初始压力为1MPa,保压压力为50MPa的烧结工艺,可以制备相对密度大于98%,平均晶粒度小于10μm的烧结铜. 同时发现,采用SPS工艺制备的烧结铜沿厚度方向存在不同于传统双向压制的密度分布,SPS烧结铜的表面密度低于心部密度.     

工艺参数对凝胶注模成型不锈钢坯体强度和烧结密度的影响

为了制备高坯体强度和烧结密度的凝胶注模成型不锈钢制件,研究了凝胶注模工艺参数包括预混液单体含量和单体/交联剂比例、浆料固相含量及引发剂加入量等对坯体抗弯强度及烧结体密度的影响规律.结果表明,对于316L不锈钢的凝胶注模成型,可同时获得较好的坯体强度和烧结密度的工艺条件为:预混液单体质量分数18%～22%,单体/交联剂比例90∶1～240∶1;浆料固相体积分数52%～55%;引发剂用量约为单体质量的0.8%～1.4%.最终获得坯体强度高于30.0MPa、烧结密度高于97%的复杂形状烧结不锈钢零件,其烧结体力学性能略低于粉末注射成型时的性能,但远高于美国MPIF标准.     

Ti-47．5Al-2．5V-1．0Cr注射成形

以Ti-47.5Al-2.5V-1.0Cr(原子分数,%)气雾化预合金粉末为原料,采用粉末注射成形工艺制备了TiAl合金材料,研究了该TiAl合金脱脂工艺对脱脂坯碳氧残留量和组织的影响规律及烧结工艺对烧结体显微组织、密度和压缩性能的影响规律. 结果表明:在脱脂温度600℃、保温时间为1h和真空脱脂气氛条件下脱除坯体中剩余粘结剂,坯体中残余碳氧含量(质量分数)分别为0.059%和0.12%;脱脂温度从600℃升到1000℃,粉末由枝状组织转变为近γ组织;烧结温度在1410～1450℃,保温时间在1h以内,烧结体可以快速致密化;在1450℃保温30min,烧结体相对密度可以达到95%,烧结体的抗压强度为2105MPa,压缩率达到30.9%,接近铸态合金力学性能;随烧结温度升高,烧结体中的γ相逐渐减少,组织由近片层组织逐渐转变为全片层组织.     

Al2O3/WC-10Co/ZrO2金属陶瓷的制备与性能

以WC-10Co纳米复合粉末、YSZ纳米粉末与Al2O3亚微粉末为原料,采用热压烧结制备了性能优良的Al2O3/WC-10Co/ZrO2金属陶瓷.分别在1380,1450和1500℃烧结温度下制备Al2O3/WC-10Co/ZrO2金属陶瓷,通过考察烧结体的断裂韧性、洛氏硬度、密度、磁滞回线和断口形貌,研究了烧结温度对WC-10Co纳米复合粉末、YSZ纳米陶瓷粉末与Al2O3亚微粉末的复合粉末烧结性能的影响.确定合理的Al2O3/WC-10Co/ZrO2金属陶瓷烧结温度为1450℃.结果表明,质量分数为50%的WC-10Co纳米复合粉末、10%的YSZ纳米陶瓷粉末与和40%的亚微Al2O3粉末的复合粉末经过48h的高能球磨后,再经过1450℃热压烧结,可以得到晶粒尺寸小于1μm的整体性能较好的亚微Al2O3/WC-10Co/ZrO2金属陶瓷,其相对密度为97.5%,断裂韧性为7.4468MPa·m1/2,硬度为HRA 94.0.     

超细晶粒W-40%Cu合金的烧结和力学性能

以纳米W,Cu粉末为原料,通过测定H2中热压烧结和无压烧结的收缩动力学曲线,研究了纳米W-40%Cu化学混合粉末的致密化过程.对比了纳米W粉与常规Cu粉(-44μm)的机械混合粉和纳米W-Cu化学混合粉的热压烧结致密化过程.测定了烧结合金在300℃和500℃下高温应力一应变曲线.实验结果表明:采用纳米W-40%Cu化学混合粉末在H2中无压烧结时最大收缩速率对应温度为980℃;1 200℃烧结平均晶粒小于2μm,相对密度为97%.纳米W-Cu化学混合粉在H2热压烧结时最大收缩速率对应温度为930℃;1 200℃烧结合金的平均晶粒为0.5 μm,相对密度为98%.纳米W-Cu化学混合粉热压合金高温抗压强度比纳米W与常规Cu粉的热压合金高.     

注凝成型技术制备CeO2基固体电解质

利用注凝成型技术制备了高致密度高电导率的CeO2 基固体电解质 .电解质素坯密度达理论密度的40 %;烧结过程中素坯失重仅为 6 %;电解质烧结体密度为理论密度的 98%,72 0℃时电导率达 0 .199S cm .     

甘氨酸-硝酸盐法合成纳米YSZ微粉及其性能

用甘氨酸-硝酸盐法合成了纳米级钇稳定化氧化锆（YS Z）微粉. 用粉末X射线衍射方法对合成产物和煅烧粉体进行物相分析, 并计算了YSZ合成粉 体的平均晶粒尺寸. 用热膨胀仪和交流阻抗谱分别研究了合成原粉的烧结收缩率和烧结样品 的电学性能. 研究结果表明, 当金属离子与甘氨酸的摩尔比为1∶2时, 用甘氨酸-硝酸盐 法可直接合成纳米级YSZ微粉, 600 ℃和1 000 ℃煅烧粉体的平均晶粒尺寸分别为9.8 5和40.5 nm. 经1 000 ℃预烧的YSZ样品的烧结性能明显高于1 200 ℃预烧YSZ样品. YSZ样 品在1 400 ℃烧结6 h的相对密度分别为99.3%和98.6%, 烧结温度范围为1 400~1 450 ℃ . 经1 450 ℃烧结后的样品在850 ℃时电导率分别为0.037和0.021 S/cm.     

甘氨酸法制备YSZ粉体及其在中温固体氧化物燃料电池中的应用

用甘氨酸法制备了堆积密度小于0．35％的疏松（Y2O3）0.08（ZrO2）0.02（YSZ）陶瓷粉体．研究了预烧温度对初级粉体的晶体结构、晶粒大小、比表面积、粉体形貌和烧结性能的影响,进一步研究预烧温度对YSZ烧结体电导率的影响．随着预烧温度的升高,粉体的晶粒尺寸增加,比表面积减小,烧结体的相对密度减小,粉体的多孔疏松程度降低．700℃预烧粉体的生坯最易致密化,得到的YSZ烧结样品具有最高电导率,其值在800℃时为0．029S·cm^-1．同时以700℃预烧的粉体为原材料,用共压共烧工艺,制备阳极支撑的厚度为10-20μm的YSZ电解质薄膜．以YSZ薄膜为基础的单电池在700℃下的最大功率密度达到470mW／cm^2．     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.