Phase formation,texture evolutions,and mechanical behaviors of Al0.5CoCr0.8FeNi2.5V0.2 high-entropy alloys upon cold rolling

The cold rolling (CR) reduction dependence of microstructure evolutions and mechanical properties for Al_0.5CoCr_0.8FeNi_2.5V_0.2 high-entropy alloy (HEA) were investigated. The HEA remains FCC structures consisting of nanoscale ordered L1₂ phase, confirming the phase formation prediction. With increasing CR reduction, the textures transform from random ones to FCC rolling ones accompanied by dense slip bands and deformation twins. Under a 50% CR reduction, the deformation textures started to become evident and were governed by typical {111}<112>F, {110}<100>Goss and {112}<111>Cu texture components. When the CR reduction approached 90%, the deformation textures mainly contained the {110}<111>A, {114}<110>X, and {112}<111>Cu texture components. As a result, both Vickers hardness and ultimate strength increased, but the ductility decreased roughly. The enhanced strength should be attributed to the anisotropy and work hardening behavior from textures. The plastic deformation for the samples under low CR reductions was dominated by deformation twins and slip bands. However, under high CR reductions, the textures severely impeded the further propagation of pre-existing slip bands, leading to the rapid decrease of ductility. Therefore, the CR reduction should be carefully designed before optimal heat treatments to enhance the strength and ductility synergy.     

Crystal morphology of sucrose influenced by rotation axes parallel to growth planes

Three different types of growth forms of sucrose (P2₁) were found by calculating with the Fourier transform method of crystal morphology. The observed central distances of the (100) and (001) faces are smaller than those calculated. It will be shown that the two-fold screw axis, which runs parallel to these faces, influences the rate of growth. The effectiveness of these symmetry elements is relative to the rotation angle around the face normal. 32th Communication.     

Determination of crystal structure of omphacite

The chemical formula of omphacite was expressed with (MⅡ MⅠ ) (Si, AI)2O6. Cations that occupied the MⅡ site were large cations such as Ca or Na, and (Na/(Na+Ca)) ratio ranged from 0.2 to 0.8; the 6-coordinated MⅠ site accommodated cations such as Mg, Fe2+, Al, Fe3+ ,and(AI/(AI+Fe3+)) ratio was more than 0.5. Omphacite space groups reported were C2/ c, P2, P2/n, P2/c, cell parameters are α0 = 0.9600-0.9630 nm,b0 = 0.8750-0.8830 nm,c0 = 0.5230-0.5290 nm,β = 106°40′-107°10'. The sample was picked up from the eclogites in Zhucheng County, Shangdong Province. The intensity data were collected with the RIGAKU RASA Ⅱ -S four-circle single crystal diffractometer.The correct structure model was obtained by using the Patterson method and Fourier synthesis, SHELX-76 program, structure refinement with 905 independent diffraction points (| F0 |> 3σ |F0 |). After the structure parameter refinement, the R-factor reduced to 0.0515. The crystal structure analysis indicates that omphacite has a new space group-Pn space group.     

Heteroseneous oxidation of carbonyl sulfide on mineral oxides

Heterogeneous oxidation of carbonyl sulfide （OCS） on mineral oxides including SiO2, Fe2O3, CaO, MgO, ZnO and TiO2, which are the main components of atmospheric particles, were investigated using in situ diffuse reflectance infrared Fourier transform spectroscopy （in situ DRIFTS）, ion chromatography （IC）, temperature-programmed desorption （TPD）, X-ray diffraction （XRD） and Brunauer-Emmett-Teller （BET） methods. The main products and intermediates of the heterogeneous oxidation of OCS on these oxides were identified with in situ DRIFTS and IC. The reaction mechanism and kinetics were also discussed. It is found that the reaction mechanism on these mineral oxides is the same as that on Al2O3 for the same final products and the intermediates at room temperature. Namely, OCS can be catalytically oxidized to produce surface SO4^2- species and gaseous CO2 through the surface hydrogen thiocarbonate （HSCO2-） and HSO; species. The activity series for heterogeneous oxidation of OCS follows： Al2O3 ≈ CaO 〉 MgO 〉 TiO2 ≈ ZnO 〉 Fe2O3 〉 SiO2. The specific area, basic hydroxyl and surface basicity of these oxides have effect on the reactivity. This study suggests that heterogeneous reactions of OCS on mineral dust may be an unneglectable sink of OCS.     

Influence of deposition time on the morphology and optical properties of SiO<Subscript>2</Subscript>-ZnO composite photonic crystals

SiO2 photonic crystal were successfully prepared by vertical deposition and then used as a template to fabricate SiO2-ZnO composite photonic crystals on ITO substrates by electrodeposition and subsequent calcination. A number of different deposition times were used. The morphologies of the silica opals and SiO2-ZnO composite photonic crystals were investigated by scanning electron microscopy. It was found that ZnO particles grew randomly on the surfaces of the silica spheres when the deposition time was short. As the deposition time was increased, the ZnO particles grew evenly on the surfaces of the silica spheres so that the interstitial space of the silica template was filled with ZnO particles. Reflectance spectra of the SiO2-ZnO composite crystals revealed that all of the fabricated photonic crystals exhibit a photonic band gap in the normal direction.     

SiO2 glasses synthesized at 355–445°C and 2.0–5.5 GPa

A series of SiO₂ glasses were synthesized by using spectroscopically pure silica on the YJ-3000 multi-anvil apparatus at 355–445°C and 2.0–5.5GPa. Their spectroscopic characteristics resemble that of the high-density quartz glass. In the meantime, the IR spectra of SiO₂ glasses show that a small amount of water exists in SiO₂ glasses in the form of OH^-. It may be due simply to the small amount of water that contributes significantly to the amorphism of SiO₂. The determination of refraction indices of SiO₂ glasses shows that the refraction indices of SiO₂ glasses and the high-density quartz glass are in good logarithmic relation with synthetic pressures.     

Growth mechanisms of Ag and Cu nanodendrites via Galvanic replacement reactions

Dendritic silver and copper crystals were produced via Galvanic replacement reactions on zinc and aluminum plates, respectively. The growth orientations of these metals were determined using electron microscopy. The results showed that a fast crystal growth associated with a high concentration of metal cations led to kinetically controlled growth along the <112> axes of the cubic close-packed structures. However, a slow growth rate resulted in thermodynamically controlled growth along the [111] axis. The crystal growth was not found to rely upon the direct deposition of metal cations at crystallographic sites on crystal facets, but instead, hydrated metal cations deposited on the crystal surface to form an amorphous coating layer, followed by the reduction of metal cations and crystallization at the crystal/coating interface. Twin defects and stacking faults were often observed across the whole particle and commonly observed ?{422} diffraction spots were explained by stacking faults rather than by the possible presence of any superstructures. The present work offers evidences to claim that both the crystal growth rate and Coulomb interaction between negatively charged crystal surface and metal cations play an important role in the formation of metal dendrites in replacement reactions.     

Structural and magnetic properties of ZnFe2O4 films deposited by low sputtering power

To validate the correctness of the Hartman-Perdok Theory (HPT), which indicates that the {111} planes have the lowest surface energy in spinel ferrites, the {111} plane orientated ZnFe₂O₄ thin films on Si(100), Si(111), and SiO₂(500 nm)/Si(111) substrates were obtained through a radio frequency (RF) magnetron sputtering method with a low sputtering power of 80 W. All of the experiments prove that the atom energy determined by sputtering power plays an important role in the orientated growth of the ZnFe₂O₄ thin films, and it matches well with HPT. The ZnFe₂O₄ thin films exhibit ferromagnetism with a magnetization of 84.25 kJ/mol at room temperature, which is different from the bulk counterpart (antiferromagnetic as usual). The ZnFe₂O₄ thin films can be used as high-quality oriented inducing buffer layers for other spinel (Ni, Mn)Zn ferrite thin films and may have high potential in magnetic thin films-based devices.     

Flux-Bridgman growth and characterization of Mn-doped ZnO single crystals

Mn-doped ZnO single crystals have been grown by the flux-Bridgman method from a high temperature solution of 24% ZnO-76%PbF_2(molar fraction).A fast nucleation was induced by the gas-cooling system at the bottom of the Pt crucible.A red Mn.ZnO crystal up to 13 mm×15 mm×(3-4) mm was obtained.Powder XRD patterns showed that the as-grown crystals were in wurtzite structure.Electron Probe Microanalyser(EPMA) revealed that some PbF_2 inclusions formed due to fast nucleation.The additional Raman mode at 524 cm ' ...     

Kinetics of C2(a3Πu) radical reactions with NO, N2O, O2, H2 and NH3

Pulsed laser photolysis/laser-induced fluorescence (LP-LIF) is utilized to measure rate constants for C₂(a³Π_u) reactions with NO, N₂O, O₂, H₂ and NH₃. Multiphoton dissociation of C₂Cl₄ at 266 nm is employed for the generation of C₂(a³Π_u) radicals. The C₂(a³Π_u) concentration is monitored by the fluorescence of the (0, 0) band of the (d³Π_g&#8596;a³Π_u) transition at 516.5 nm. C₂(a³Π_u) removal rate constants for the reactions are determined as k_NO = (5.46 ± 0.10) × 10^-11 cm³ molecule^-1 s^-1 , k_N2O = (1.63 ± 0.20) × 10^-13 cm³ molecule^-1 s^-1 , k_N2O = (1.58 ± 0.16) × 10^-11 cm³ molecule^-1 s^-1, k_O2 = (5.92 ± 1.00) × 10^-14 cm³ molecule^-1 s^-1, k_H2< 1.0× 10^-14 cm³ molecule^-1 s^-1. Based on the data analysis and theoretical calculation, we suggest that the C₂(a³Π_u) reactions with H₂ and NH₃ proceed via the hydrogen abstraction mechanism, barriers exist at the entrance channel of the reactions of C₂(a³Π_u) with H₂ and NH₃.     

Preparation by a rheological phase reaction method and thermal decomposition reaction mechanism of nickelous salicylate tetrahydrate

0　IntroductionInrecentyears,studiesonBinghamfluid ,suchasElec trorheologicalfluid ,areactivelypursued[1 6] .Rheologicaltechniqueshavebeenplayinganimportantroleinsyntheticchem istry .Therheologicalphasereactionmethodisthe processofpreparingcompoundsormaterialsfromasolid liquidrheologicalmixture.Thatis,thesolidreactantsarefullymixedinapropermolarratio ,andmadeupbyaproperamountofwaterorothersolventstoaBinghambodyinwhichthesolidparticlesandliquidsubstanceareuniformlydistributed ,sothattheprodu…     

Refinement of the crystal structure for a new mineral──antimonselite

The crystal structure of a new mineral of the stibnite group, Sb-2Se-3, has been determined. The cell constants, obtained by least-squares calculation from direct θ -value's measurements on the diffractometer are: a =1.158 8(5), b =1.174 4(4), c =0.395 5(2) nm; orthorhombic; V =0.538 23 nm+3; Z =4. The space group is Pbnm. X-ray single crystal data, using Mo K α radiation, were measured on a RIGAKU RASA-5RP automated diffractometer and refined to a final R index of 0.048 1. Sb-2Se-3 is isostructural with Sb-2S-3 and Bi-2S-3. Each Sb(1) atom is six-coordinated by 3 Se(1), 1 Se(2) and 2 Se(3) atoms at distances 0.266 0-0.323 6 nm. Each Sb(2) atom is seven-coordinated by 2 Se(1), 2 Se(2) and 3 Se(3) atoms at distances of 0.258 1- 0.346 7 nm. The crystal structure consists of chains parallel to c or needle axis. The strongest bonds (shortest separations) are within the chains. Many important physical properties of antimonselite (optical, ferroelectric, etc.) are related to its crystal structure.     

TiO2/SiO2复合光催化剂制备工艺参数优化及其表征

先以无机钛盐、硅酸盐为原料制取聚合硅酸硫酸钛,再通过液相水解法制得TiO2/SiO2复合光催化剂,并用SEM、XRD、BET和甲基橙脱色率对复合光催化剂进行表征。结果表明,TiO2/SiO2复合光催化剂制备优化工艺参数为:Ti(SO4)2作钛源、Ti/Si摩尔比为12∶1、水解反应pH值为6、煅烧温度为650℃,以此条件制备的复合光催化剂对甲基橙脱色率可达98.6%以上;TiO2/SiO2复合光催化剂为一种分散均匀的纳米级球形颗粒,其成分为以锐钛矿为主的TiO2,SiO2的复合有效抑制了TiO2晶粒的生长,同时提高了TiO2的热稳定性。     

Morphologic characteristics and growth interface stability of nano-micron FeS2 whiskers

Micromorphology is further studied on the basis of our previous researches concerned with the nano-micron FeS2 whisker. There are obvious differences in the intensive degree, diameter and micro- morphology among the FeS2 whiskers growing in different stages. From the early to late stage, the intensive degree increases, the diameter decreases, and the surface micro-morphology changes following the regularity： protrusive nodulation → coarse → smooth → flat. According to the theory of crystal growth, the geological setting and processes of whisker formation, we discuss the stability and evolution of crystal growth interface of FeS2 whisker occurring in Gengzhuang gold deposit （Shanxi Province, China）. The results suggest that the negative temperature gradient and the supercooling appear in the early stage of the whisker growth, whereas the positive temperature gradient of reposeful state appears in the late stage. In the whisker growth stage, the component concentration changes through the three stages： severely nonhomogeneous in the early stage, relatively homogeneous in the middle stage, more homogeneous in the late stage. The general changing process of the interfacial state is from unstable to stable. Micromorphology of FeS2 whisker in Gengzhuang is the result of synergism of temperature, component concentration and stability of crystal interface phase in hydrothermal system. The micromorphology not only reflects the physical and chemical characteristics of the hydrothermal system during the whisker growth, but also indicates the stability characteristics of the interface phase and records the changing process of the whisker growth.     

Study on flow characteristics of solid/liquid system in lysozyme crystal growth

During the process of lysozyme protein crystallization with batch method,the macroscopic flow field of solid/liquid system was observed by particle image velocimetry(PIV). Furthermore,a normal growth rate of(110) face and local flow field around a single protein crystal were obtained by a long work dis-tance microscope. The experimental results showed that the average velocity,the maximal velocity of macroscopic solid/liquid system and the velocity of local flow field around single protein crystal were fluctuant. The effective boundary layer thickness δeff,the concentration at the interface Ci and the characteristic velocity V were calculated using a convection-diffusion model. The results showed that the growth of lysozyme crystal in this experiment was dominated by interfacial kinetics rather than bulk transport,and the function of buoyancy-driven flow in bulk transport was small,however,the effect of bulk transport in crystal growth had a tendency to increase with the increase of lysozyme concentra-tion. The calculated results also showed that the order of magnitude of shear force was about 10-21 N,which was much less than the bond force between the lysozyme molecules. Therefore the shear force induced by buoyancy-driven flows cannot remove the protein molecules from the interface of crystal.     

Some polar sets for the generalized Brownian sheet

Let (t)(t ∈ R ₊ ^N ) be the d-dimensional N-parameter generalized Brownian sheet. We study the polar sets for (t). It is proved that for any a ∈ R ^d , P{ (t) = a, for some t ∈ R _> ^N } = and the probability that (t) has k-multiple points is 1 or 0 according as whether 2kN > d(k − 1)β or 2kN < d(k−1)α. These results contain and extend the results of the Brownian sheet, where R _> ^N = (0,+∞) ^N ,R ₊ ^N =[10,+∞) ^N ,0< α≤1 and β≥1. Biography: LI Huiqiong (1966–), female, Associate professor, research direction: stochastic process and random fractal.     

Morphological characteristics of α-Al2O3 crystallites obtained direct1y from hydro /solvothermal solvents

The morphological characteristics of α-Al₂O₃ crystallites obtained directly from hydro/solv othermal solvents are reported and the formation mechanisms of corundum morphology are discussed from crystal growth and crystal chemistry principles. The crystal growth process is considered as a process of incorporation of growth units on the growth interfaces, and the crystal morphology is determined by the linkage of the coordinated polyhedra.     

Growth of AgGaS2 single crystal by descending crucible with rotation method and observation of properties

This note reports a new procedure of polycrystalline synthesis and a new technique of single crystal growth on AgGaS₂, i.e. two-zone temperature oscillation vapor transporting and descending crucible with rotation. A single phase dense AgGaS₂ polycrystalline ingot was synthesized, and a crack-free AgGaS₂ single crystal with 15 mm in diameter and 30 mm in length was grown by the techniques mentioned above. Structure integrity of the crystal was studied by the X-ray diffraction technique. Six order X-ray spectra from the 011 face of the crystal were obtained, and an anomalous phenomenon was observed for the first time that intensity of the higher order diffraction peak is much stronger than that of the lower order diffraction peak. Etch-pits of the crystal were observed by the scanning electron microscopy (SEM).     

Molecule modification and mass deposition induced by the implantation of low energy Fe+ ion beams into amino acids

Fe⁺ ion beams with the energy of 110 keV were implanted into films of L(+)-cysteine (HSCH₂CH(NH₂)COOH). One of the single crystals grown in hydrochloric acid solution with the implanted samples through slow evaporation was structurally characterized by the X-ray crystallography. The crystal is monoclinic, space group C2, with a = 1.8534(4) nm, b = 0.5234(1) nm, c = 0.7212(1) nm, β= 103.72°, V = 0.67965(3) nm³, Z = 4, F(000) = 144.0, D{clac} = 1.763 g · cm⁻³, μ(MoK _a = 1.06 mm⁻¹, T = 293(2) K. R = 0.0379, wR = 0.0835 for 660 observed reflections (I > 2σ(I)). The structural formula of the crystal compound is (CH₂CH(NH₂)NO₂)ClFe (M _r = 180.38 u). Products of heavy ion beam irradiation were purified and it was directly confirmed that the implanted Fe⁺ ions had been deposited in the novel molecules. The same doses of Fe⁺ ion beams of the same energy were implanted into films of L(+)-cysteine hydrochloride monohydrate. FTIR spectroscopy of the implanted samples proved that some of the original molecules were seriously damaged and significant modifications were induced.     

磷酸钇晶体物理性质及本征缺陷的研究

运用GULP软件并采用已有的势参数计算了理想YPO_4晶体的物理性质和本征缺陷,得到的晶体结构参数与实验结果基本吻合.根据计算得到的力学性质表明,YPO_4晶体在(100)方向的抗应变能力最强.对YPO_4晶体的热学性质的计算结果表明,不能忽略在高温条件下振动熵对YPO_4晶体本征点缺陷形成能的影响.由本征点缺陷形成能的计算结果得知氧空位和氧的弗伦克尔缺陷在晶体中相对容易形成.