一步法合成耐久性水基超疏水TiO2/DTMS涂层

为制备具有优异自清洁功能的耐久性水基超疏水涂层，以十二烷基三甲氧基硅烷(n-dodecyltrimethoxysilane, DTMS)为有机改性物，通过一步法在纳米TiO₂表面嫁接长链烷基官能团得到超疏水TiO₂/DTMS涂层。分析了TiO₂涂层及TiO₂/DTMS涂层的表面润湿性、形貌和化学组成，并对所得超疏水TiO₂/DTMS涂层的自清洁性能、机械及化学稳定性进行了测试。结果表明：超疏水TiO₂/DTMS涂层表面水接触角(water contact angle, WCA)达到159°；以亚甲基蓝粉末作模拟污染物，涂覆有超疏水TiO₂/DTMS涂层的玻璃具有优异的自清洁性能；经机械磨损(10 min)、酸碱液(pH=1、3、5、7、9、11、13)浸泡、高低温(−20、30、60、90、120、150 ℃)处理后超疏水TiO₂/DTMS涂层的WCA仍大于150°，表明其具有优异的机械和化学稳定性，可用于室外防污，如建筑物外墙、玻璃、太阳能电池板等。     

Modification of TiO2 nanotubes arrays by CdS and their photoelectrocatalytic hydrogen generation properties

In order to realize hydrogen generation under visible light, novel CdS/TiO2 nanotubes arrays are developed by electrochemical anodizaUon of Ti in 0.15 mol/L NHTF ＋ 0.08 mol/L H2C2O4 electrolyte. The diameter of the nanotube is 80-100 nm and the length is approximately 550 nm. The CdS nano-particles are deposited on the TiO2 nanotubes arrays by chemical bath deposition （CBD） in the ammonia-thiourea system. A 300 W Xe lamp is used as the light source, CdS/TiO2 nanotube arrays are used as the photoanode with the application of 1.0 V bath voltage, and 0.1 mol/L Na2S ＋ 0.04 mol/L Na2SO3 solution is used as the electrolyte, then the rate of photoelectrocatalytic hydrogen generation is 245.4 μL/（h·cm^2）. This opens new perspectives for photoelectrocatalytic hydrogen generation by using CdS/TiO2 nanotubes arrays.     

基于SnO2/TiO2/Au NPs纳米复合材料发展光电化学方法特异性检测唾液酸

制备了氧化铟锡（ITO）/二氧化锡（SnO₂）/二氧化钛（TiO₂）/金纳米粒子（Au NPs）纳米复合电极（ITO/SnO₂/TiO₂/Au NPs）,并利用它发展了可以选择性检测唾液酸（SA）的光电化学（PEC）法.采用旋涂法制备了ITO/SnO₂电极,并通过静电纺丝和磁控溅射技术在ITO/SnO₂表面原位合成了TiO₂纳米纤维和Au NPs.与单纯SnO₂比,ITO/SnO₂/TiO₂/Au NPs纳米复合电极的光电性能显著提高.这可能与Au NPs的局域表面等离子体共振效应（LSPR）和TiO₂/SnO₂异质结之间的协同作用密切相关.之后,通过金硫键（Au-S）将四巯基苯硼酸（4-MPBA）修饰在ITO/SnO₂/TiO₂/Au NPs电极表面,利用4-MPBA和SA之间的非特异性酯化反应,发展了可以特异性检测SA的PEC传感平台.     

水热体系下二氧化钛与氧化石墨烯复合纳米晶的合成

 200 ℃下四方结构的二氧化钛(TiO2)与氧化石墨烯(GO)复合纳米晶在一个装有适量钛酸四丁酯、无水乙醇、氧化石墨烯和蒸馏水的密闭的水热釜中加热12 h后被制备。X射线粉末衍射仪（XRD)、扫描电子显微镜（SEM）、透射电子显微镜（TEM）等一系列分析仪器被运用来揭示二氧化钛与氧化石墨烯复合纳米晶是由粒径大约160 nm的四方结构的二氧化钛纳米晶与氧化石墨烯复合而成,通过紫外吸收对其光学性能进行了必要的测试。
     

Preparation and photocatalytic activity of Cu-doped TiO2/SiO2

Cu²⁺-doped nanostructured TiO₂-coated SiO₂ (TiO₂/SiO₂) particles were prepared by the layer-by-layer assembly technique and their photocatalytic property was studied. TiO₂ colloids were synthesized by the sol-gel method using TiOSO₄ as a precursor. The experimental results showed that TiO₂ nanopowders on the surface of SiO₂ particles were well distributed and compact. The amount of TiO₂ increased with the increase in coating layers. The shell structure appeared to be composed of anatase titania nanocrystals at 550°C. The 2-layer coated TiO₂ particles on the surface showed a higher degradation rate compared with all the different-layer samples. The photocatalytic activity of Cu²⁺-doped TiO₂/SiO₂ was higher than that of undoped TiO₂/SiO₂. The optimum dopant content was about 0.10wt%.     

碳量子点修饰的二氧化钛纳米片阵列薄膜的构筑及光电化学性能*

为了提高纳米二氧化钛(TiO_2)的光电化学性能,首先采用水热法,以稀盐酸、钛酸丁酯和氟钛酸铵作为原料,在掺杂氟的氧化锡(FTO)导电玻璃上制备了(001)面主导的TiO_2纳米片阵列薄膜。通过电化学腐蚀法制得均一、稳定、高活性碳量子点(carbon quantum dots,CQDs),再通过电泳法将CQDs修饰到TiO_2纳米片阵列薄膜表面,形成CQDs/TiO_2纳米片阵列复合材料。利用扫描电镜(scanning electron microscope,SEM)、 X射线衍射(X-ray diffraction,XRD)、拉曼光谱、X射线光电子能谱(X-ray photoelectron spectroscopy,XPS)和紫外可见光谱(UV-vis)对复合材料的形貌、晶型、表面元素成分和光吸收能力进行表征,通过电化学工作站测试复合材料的光电化学性能。结果表明:CQDs/TiO_2复合材料为锐钛矿晶型,形貌规整均匀;CQDs修饰后TiO_2纳米片的最大吸收波长由388 nm增加到576 nm,光化学能转化率高达2.38%,光电流是TiO_2纳米片的8倍,交流阻抗减小,具有非常优异的光电化学性能。     

TiO2/SiO2复合光催化剂制备工艺参数优化及其表征

先以无机钛盐、硅酸盐为原料制取聚合硅酸硫酸钛,再通过液相水解法制得TiO2/SiO2复合光催化剂,并用SEM、XRD、BET和甲基橙脱色率对复合光催化剂进行表征。结果表明,TiO2/SiO2复合光催化剂制备优化工艺参数为:Ti(SO4)2作钛源、Ti/Si摩尔比为12∶1、水解反应pH值为6、煅烧温度为650℃,以此条件制备的复合光催化剂对甲基橙脱色率可达98.6%以上;TiO2/SiO2复合光催化剂为一种分散均匀的纳米级球形颗粒,其成分为以锐钛矿为主的TiO2,SiO2的复合有效抑制了TiO2晶粒的生长,同时提高了TiO2的热稳定性。     

Preparation of Zn-doped TiO2 nanotubes electrode and its application in pentachlorophenol photoelectrocatalytic degradation

Zn-doped titanium oxide （TiO2） nanotubes electrode was prepared on a titanium plate by direct anodic oxidation and immersing method in sequence. Field emission scanning electron microscopy （FESEM） showed that the Zn-doped TiO2 nanotubes were well aligned and organized into high density uniform arrays with diameter ranging from 50 to 90 nm. The length and the thickness were about 200 and 15 nm respectively. TiO2 anatase phase was identified by X-ray diffraction （XRD）. X-ray photoelectronspectroscopy （XPS） indicated that Zn ions were mainly located on the surface of TiO2 nanotubes in form of ZnO clusters. Compared with TiO2 nanotubes electrode, about 20 nm red shift in the spectrum of UV-vis absorption was observed. The degradation of pentachlorophenol （PCP） in aqueous solution under the same condition （initial concentration of PCP： 20 mg/L; concentration of Na2SO4：0.01 mol/L and pH： 7.03） was carried out using Zn-doped TiO2 nanotubes electrode and TiO2 nanotubes electrode. The degradation rates of PCP using Zn-doped TiO2 nanotubes electrode were found to be twice and 5.8 times as high as that using TiO2 nanotubes electrode by UV radiation （400 μw/cm^2） and visible light radiation （4500 μw/cm^2）, respectively. 73.5% of PCP was removed using Zn-doped TiO2 nanotubes electrode against 45.5% removed using TiO2 nanotubes electrode in 120 min under UV radiation. While under visible light radiation, the degradation efficiency of PCP was 18.4% using Zn-doped TiO2 nanotubes electrode against 3.2% using TiO2 nanotubes electrode in 120 min. The optimum concentration of Zn doping was found to be 0.909%. The PCP degradation efficiencies of the 10 repeated experiments by Zn-doped TiO2 nanotubes electrode were rather stable with the deviation within 3.0%.     

TiO2/SiO2/GQDs双层增透膜的制备及其在太阳能板中的应用

采用溶胶-凝胶法制备了SiO₂ 和TiO₂ 纳米溶胶,采用水热法制备了石墨烯量子点（graphene quantum dots,GQDs）。为进一步提高光伏太阳能板的透光率,设计了一种TiO₂/SiO₂/GQDs双层增透膜结构。探究了薄膜的结构、自清洁性能和增透性能,并进一步讨论了GQDs在增透性中的作用。结果表明,SiO₂-TiO₂/TiO₂-GQDs结构的双层薄膜厚度为120 nm时,太阳能板上的光透过率由未涂敷的85%增加至95%。接触角实验和室外耐环境性能实验测试表明,复合膜层接触角为10°,并具有良好的亲水性和耐环境性能。此外,户外实验结果表明,涂覆该薄膜的太阳能电板发电效率提高6%。由此说明双层增透膜可有效地提高太阳能电池板的光能利用率和使用寿命,可高效地利用太阳能。     

Fe_2O_3/TiO_2复合纳米管阵列的制备及其可见光催化性能研究

在氟化铵-乙二醇体系中,采用阳极氧化法在铁基体上制备Fe_2O_3纳米管阵列,然后以氟钛酸铵为钛源,利用水热法在Fe_2O_3纳米管阵列上负载TiO_2纳米片,制得Fe_2O_3/TiO_2复合纳米管阵列,利用SEM、EDS、XRD、TEM、UV-Vis等手段,对所制Fe_2O_3/TiO_2纳米管阵列的表面形貌、物相结构及光催化性能进行表征,并分析Fe_2O_3/TiO_2纳米结构对亚甲基蓝的可见光降解能力。结果表明,Fe_2O_3/TiO_2复合纳米管阵列具有良好的可见光响应;NH_4F浓度为0.4%、水热反应3h制备的Fe_2O_3/TiO_2复合结构具有最佳的光催化性能,对亚甲基蓝的降解率可达90%。     

Photovoltaic properties of MEH-PPV/TiO2 nanocomposites

Photovoltaic properties of photodiodes based on nano-TiO2 and poly[2-methoxy,5-（2＇-ethlhexyloxy）-p-phenylenevinylene] （MEH-PPV） composites are investigated. By comparing composite devices with the same weight of TiO2 （nanoparticles and nanotubes）：MEH-PPV, it was found that the device with TiO2 nanotubes exhibited better performance. By further optimizing the weight radio of TiO2 nanotubes： MEH-PPV, we gained the device with a short circuit current density of 9.27μA/cm^2 with a light intensity of 16.7mW/cm^2 at the 500 nm wavelength, the highest open-circuit voltage of 1.1V, and a photosensitivity of 332 at reverse bias of -0.6V. The photosensitivity is improved by a factor of 33 compared with the undoped MEH-PPV device.     

Morphological structure and physicochemical properties of nanotube TiO2

Morphological structure and physicochemical properties of nanotube TiO₂ were investigated. It was found that the TiO₂ nanotube consisted of 2–5 monolayers of TiO₂ molecules, and its inner diameter was between 4.2 and 5.9 nm. The nanotube TiO₂ powder had high specific surface area and pore volume (379 m²/g and 1.431 cm³/g respectively) and its decolorization activity for Reactive Brilliant Red X-3B was 2 times higher than that of raw TiO₂ (p-25). This new type of TiO₂ was hopeful for application in photocatalysis and composite nanomaterial.     

TiO2对磁控溅射Ti-TiO2纳米复合涂层抗菌性能的影响

为预防种植体周围炎,采用反应磁控溅射法在纯Ti片表面制备了Ti-TiO₂纳米复合涂层,改变Ti靶材与TiO₂靶材的拼接比例,研究纳米TiO₂体积分数对涂层微观结构和抗菌性能的影响。采用扫描电子显微镜、能谱仪、X射线衍射仪、原子力显微镜、接触角测量仪对样品进行微观组织的表征以及表面粗糙度和润湿性能的测量,采用CCK-8法(cell counting kit-8,CCK-8)对涂层进行细胞毒性测试,采用平板涂布计数法对涂层进行抗菌性能评价。结果表明,当Ti靶材与TiO₂靶材的拼接比例为95∶5时,Ti-TiO₂涂层含纳米TiO₂量最多,涂层的表面粗糙度以及与液相接触角达到最大值,分别为1.28 nm和100.42°,涂层无细胞毒性,符合生物安全性材料的标准,涂层的抗菌性能最佳,涂层的抑菌率达到了90.94%。     

银掺杂多孔氧化钛光催化甲基橙降解反应条件的探究

利用溶胶-凝胶法结合光还原法制备Ag掺杂多孔TiO_2光催化剂,以甲基橙的降解效果为评价标准,考查了光照降解时间、光催化剂用量、甲基橙溶液初始浓度、溶液pH值对光催化剂催化降解甲基橙的影响。结果表明,本方法制备的光催化剂无论是在紫外光还是可见光下均具有优良的光催化性能:在浓度为10 mg/L的甲基橙溶液中,4 g/L光催化剂,紫外光照射80 min,甲基橙可实现100%完全降解;相同催化条件下,可见光照100 min,甲基橙完全降解;当反应溶液pH=2时,紫外光和可见光都可在20 min内实现甲基橙的完全降解。     

The comparison of Cu（ll） adsorption capability of baker＇s yeast,nano-titania and their composite adsorbent

The anatase nano-TiO2 powder, with crystal size between 40 and 80 nm, was prepared by the liquid phase hydrolysis of TiCI4. At the same time, the nano-TiO2 was utilized with the baker＇s yeast biomass as a composite adsorbent to adsorb the Cu ions in the artificial aqueous solution. The investigation showed that the composite adsorbent had a fine adsorption efficiency. The TiO2 in the composite adsorbent could cooperate well with baker＇s yeast to improve the adsorbing capability of Cu^2＋ under the following experimental conditions as well： a quantity of composite adsorbent of 5 g·L^-1, pH≥4.0, an adsorption time of 40 min and an initial concentration of Cu ions of 10 mg·L^-1. In addition, the results of measurements, obtained with a scanning electron microscope, an infrared spectrophotometer and a Zeta potential analyzer, revealed that the baker＇s yeast and nano-TiO2 produced the composite adsorbent through coordination and hydrogen bonds in particular, etc. The stability of the composite adsorbent and the amount of titania loaded were largely dependent on the concentration of hydrogen ion in the solution.     

Preparation and magnetic properties of CoFe2O4/TiO2 composite films

Using （Ti（OC4H9）4） and metal chlorates as starting materials, CoFe2O4/TiO2 composite films were prepared by sol-gel method. The effects of heat treatment temperature and pH of the precursor on microstructure and magnetic properties were studied. The phase structure of the samples was examined by X-ray diffraction. The microstructure was examined by scanning electron microscope, atomic force microscope and polarized microscope. The magnetic property was measured by vibrating sample magnetometer. The results show that the crystals of different phases grow up independently. CoFe2O4 is uniformly embedded into the TiO2 matrix in the prepared composite films, and the growth of composite films is dependent on the heat treatment temperatures and PH of the precursor. The average size of CoFe2O4 crystal is 19 nm in Nanocomposite film prepared when the heat treatment temperature is 800℃ and the pH of the precursor is between 2 and 3. The magnetism of the composite films is enhanced as the heat treatment temperature increases.     

CdS修饰低密度TiO2纳米棒阵列复合膜的制备及光电性能

为了提高CdS光敏层在TiO₂一维纳米棒阵列中的填充率,在TiO₂种子层的基础上,采用水热法于FTO导电玻璃表面生长了棒长较短、棒间距较大的低密度TiO₂一维纳米棒阵列膜,通过化学浴沉积在TiO₂纳米棒表面包覆CdS种子层,以此为基底采用水热法于TiO₂一维纳米阵列中生长CdS光敏层。采用SEM,XRD及紫外-可见吸收光谱对不同CdS水热生长时间的TiO₂/CdS复合膜结构进行了表征,并对其光电性能进行了研究。结果表明,低密度TiO₂纳米棒阵列有利于CdS生长液在阵列中渗入形成完全包覆的CdS种子层,CdS光敏层通过水热过程在整个TiO₂纳米棒表面均匀生长,逐渐形成CdS对TiO₂纳米棒阵列的完全填充和包覆,并在阵列顶端形成由CdS纳米短棒组成的花状修饰层;CdS的修饰将TiO₂一维纳米阵列膜的光吸收拓展至可见光区,水热生长7 h所得到的TiO₂/CdS复合膜具有最高光电流。所制备的CdS修饰低密度TiO₂纳米棒复合膜在太阳电池器件中具有很好的应用前景。     

A review on TiO2 nanotube arrays: Fabrication, properties, and sensing applications

Fabrication, properties, and sensing applications of TiO₂ nanotubes have been reviewed, and the highly ordered TiO₂ nanotube arrays made by anodic oxidation in fluoride-contained electrolytes highlighted. The effect of anodization parameters (electrolyte, pH, and voltage) on the titania nanotube size and shape were discussed. The excellent biocompatibility of TiO₂, the high orientation, the large surface area with tunable pore sizes, as well as the high electron transfer rate along with the nanotubes make TiO₂ nanotube array an ideal substrate for the sensor’s fabrication and application. The sensors based on the TiO₂ nanotube arrays for sensing hydrogen, oxygen, humidity, glucose and hydrogen peroxide all exhibited low detection limit, high stability, very good reproducibility and high sensitivity.     

Microstructure and optical absorption properties of Au/NiO thin films

Au nanoparticles dispersed NiO composite films were prepared by a chemical solution method. The phase structure, microstructure, surface chemical state, and optical absorption properties of the films were characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, and Uv-vis spectrometer. The results indicate that Au particles with the average diameters of 35–42 nm are approximately spherical and disperse in the NiO matrix. The optical absorption peaks due to the surface plasmon resonance of Au particles shift to the shorter wavelength and intensify with the increase of Au content. The bandwidth narrows when the Au content increases from 8.4wt% to 45.2wt%, but widens by further increasing the Au content from 45.2wt% to 60.5wt%. The band gap E_g increases with the increase of Au contents from 8.4wt% to 45.2wt%, but decreases by further increasing the Au content.     

Preparation and characterization of in-site regenerated TiO<Subscript>2</Subscript>-ACFs photocatalyst

In-site regenerated titanium dioxide-activated carbon fibers (TiO₂-ACFs) photocatalyst was prepared by the sol-gel method. Detailed surface and structural characterization of the TiO₂-ACFs photocatalyst was carried out. The photoactivity of TiO₂-ACFs under ultraviolet irradiation was compared with original ACFs and pure TiO₂ by the degradation of methylene blue aqueous solution. The degradation efficiency by the TiO₂ (5wt%)-ACFs sample is much higher than that by TiO₂ and ACFs. The results show that the photocatalysis by TiO₂-ACFs is a six-step process. The adsorption-transfer-photocatalysis rate of TiO₂-ACFs is higher than the adsorption-photocatalysis rate of TiO₂, so the photocatalysis rate of the TiO₂-ACFs system is higher than that of TiO₂ photocatalyst.