TiH2粉末制备钛合金的烧结脱氢规律及工艺

 以TiH₂粉末为原料,通过压制成型和烧结工艺制备粉末钛合金,不同于传统钛粉末冶金方法。通过热分析和热膨胀技术研究不同球磨粒度TiH₂粉末的脱氢和收缩规律,以此入手研究了TiH₂粉末压坯和TiH₂-Al-V粉末压坯的烧结致密特性,以及影响烧结过程的主要工艺因素,包括烧结温度、烧结时间、升温速率、压坯密度、压坯成型方式、合金体系,并对烧结组织进行了分析。结果表明,TiH₂粉末球磨后脱氢温度降低,粉末越细,开始温度越低。TiH₂粉末压坯在烧结过程中脱氢后获得新鲜钛,其易发生黏接并引起α-Ti的强烈收缩,这时烧结体很容易致密,并获得相对密度大于99%坯体;相比之下,TiH₂-Al-V粉末压坯烧结时因为合金元素的溶解,不如纯TiH₂粉末压坯的烧结容易致密。TiH₂-Al-V粉末经过成型、烧结脱氢可获得典型的层片状α+β钛合金组织,合金元素分布均匀。     

弥散强化铜致密化研究

本文对Cu-0.86V％Al_2O_3弥散强化钢(DSCu)粉末坯进行了四种致密化方法的研究和比较。讨论和观察了致密化过程中温度、压力的功能和形貌变化。认为:(1)DSCu粉末坯锭致密化应包括坯块密度的提高和颗粒结合状态的改变;(2)DSCu宜采用有应力烧结。采用致密化坯锭挤压。可使DSCu材料成品率提高20％以上。     

3Cr13粉末不锈钢的研究

采用球磨、粉末热处理、合金化及活化烧结工艺对 3Cr13粉末不锈钢性能进行了研究。结果表明,3Cr13 不锈钢粉末经 6 h 球磨,860 ℃预处理及加 2 wt％Cu可改善其压制性,提高压坯密度及烧结性能。3Cr13 粉末不锈钢在硬度、压溃方面优于实体不锈钢,用其制作水泵轴套材料是可能的。     

粉末铁基高温合金的制备工艺研究

采用粉末机械合金化-温压成型-真空烧结等方法制备了氧化物弥散强化铁基高温合金MA956,并对其制备工艺和组织性能进行了研究。结果表明,高能振动球磨4h粉末颗粒细小均匀,已经基本实现了合金化,将其在120℃、500MPa条件下进行温压成型,压坯密度比常温模压工艺提高了0．3g／cm3;烧结温度对烧结体组织和性能有较大的影响,粉末压坯在1350℃烧结其致密度最高,为90．8％,且显微组织致密性好。     

细晶Mo-40%Cu合金的烧结性能

采用溶胶—喷雾干燥—煅烧—氢还原工艺制取纳米晶Mo-40%Cu(质量分数)复合粉末,并利用该粉末制备具有优良物理力学性能的细晶Mo-40%Cu合金。研究烧结温度、时间对合金性能的影响,检测合金的物理力学性能,分析合金的显微组织与断口形貌特征。研究结果表明:采用该法制取的纳米晶Mo-40%Cu复合粉末烧结活性高,其成形压坯在1 050～1 100℃于H2气氛中烧结保温60 min即可实现材料的快速致密化,合金的相对密度可达到98%以上,最大拉伸强度和伸长率分别为630 MPa和6.97%,且组织晶粒细小(平均粒径小于1μm)。     

Ti-47．5Al-2．5V-1．0Cr注射成形

以Ti-47.5Al-2.5V-1.0Cr(原子分数,%)气雾化预合金粉末为原料,采用粉末注射成形工艺制备了TiAl合金材料,研究了该TiAl合金脱脂工艺对脱脂坯碳氧残留量和组织的影响规律及烧结工艺对烧结体显微组织、密度和压缩性能的影响规律. 结果表明:在脱脂温度600℃、保温时间为1h和真空脱脂气氛条件下脱除坯体中剩余粘结剂,坯体中残余碳氧含量(质量分数)分别为0.059%和0.12%;脱脂温度从600℃升到1000℃,粉末由枝状组织转变为近γ组织;烧结温度在1410～1450℃,保温时间在1h以内,烧结体可以快速致密化;在1450℃保温30min,烧结体相对密度可以达到95%,烧结体的抗压强度为2105MPa,压缩率达到30.9%,接近铸态合金力学性能;随烧结温度升高,烧结体中的γ相逐渐减少,组织由近片层组织逐渐转变为全片层组织.     

SPS烧结TiO2／Al90Mn9Ce1微胞陶瓷金属基块体复合材料

用表面包覆8wt％TiO2纳米粉末的微米Al90Mn9Ce1合金复合粉末，制备了高致密的闭合微胞陶瓷结构，内充金属合金的块体复合材料，烧结温度仅为520℃，烧结后的致密度达到98．2％。SEM观察结果显示，该材料的陶瓷胞壁厚度约为1．0～2．0μm，胞体尺寸约为15～40μm，经10％HCl深腐蚀后，留下完整的微胞状陶瓷骨架。根据实验结果，对SPS烧结微-纳米混合粉体的瞬时界面烧结机理进行探讨。     

一种烧结铁基合金Fe-Cr-Mo-Ni-Co-C的热致密化过程

利用金相、扫描电镜和密度测试等方法研究Fe-Cr-Mo-Ni-Co-C合金的致密化过程，烧结过程中烧结密度与压实密度的关系，烧结致密化过程中孔隙的变化规律与烧结体积的收缩规律。通过研究舍金烧结体积的收缩规律，提出临界压坯密度的概念，并从理论上推导出临界压坯密度计算方程。研究结果表明：合金中的孔隙主要有2种类型，即粒径为30μm左右的大孔隙和粒径在10μm以下的小孔隙，这2种孔隙分别由生坯中的2种主要间隙在烧结过程中演变而成。     

烧结压力对Al90Mn9Ce1合金SPS致密化的影响

采用放电等离子烧结（SPS）技术,在50MPa,300MPa,600MPa单轴压力下,对固结气雾化法制备的粒度为20-45μm的Al90Mn9Ce1合金粉末,研究了压力和脉冲电流作用下的致密化过程。结果表明,提高烧结压力有助于粉末的塑性变形和幂率蠕变,促进Al90Mn9Ce1合金压坯的致密化。当烧结压力为600MPa时,在660K保温0min条件下,样品致密度达到99．2％,强度达到1048．5MPa,原始颗粒之间形成宽度为20nm的熔合区,界面结合良好。     

机械活化Mo－Cu粉末的烧结

研究了Ｍｏ－Ｃｕ粉末，经机械活化处理后的组织、形态与液相烧结性能、合金组织的关系，实验结果表明：一定时间活化处理，Ｍｏ－Ｃｕ粉末形成机械合金化初期的层状组织，其压坯可在较低温度液相烧结，合金相对密度大于９９％，组织细小、均匀。     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.