高能球磨对TiC0.5/Cu(Al)复合材料组织和性能的影响

以Ti2AlC和Cu粉作为原料,分别采用滚筒球磨和高能球磨对原料粉进行预混处理,在1 150℃下原位热压反应制备了TiC0.5/Cu(Al)复合材料.实验结果表明,Al从Ti2AlC溶出进入Cu中,Ti2AlC分解并转变成TiC0.5相,然而滚筒球磨制备的复合材料中生成少量AlCu2Ti相.通过对原料粉高能球磨处理,制备后的复合材料AlCu2Ti相消失,细小的TiC0.5颗粒均匀分布于基体中.两种不同方法制备的复合材料的弯曲强度和维氏硬度试验结果表明,高能球磨工艺能提高TiC0.5/Cu(Al)复合材料的弯曲强度,同时维氏硬度略有降低.其中,高能球磨处理后制备的27％ TiC0.5/Cu(Al)复合材料的弯曲强度达到981 MPa,维氏硬度为2.43 GPa.     

无机熔剂对SiC_p增强镁铝基复合材料的影响

以SiC颗粒为增强相,镁铝合金为基体,采用熔剂保护法制备了SiC颗粒增强镁铝基复合材料。利用扫描电镜和X射线衍射分析研究了SiC颗粒对材料微观形貌和成分的影响,并测定了材料密度和硬度随SiC颗粒含量的变化趋势。结果表明,加入SiC颗粒后的材料基体组织显著细化,界面化学反应有效地改善了SiC颗粒与基体的结合状态。同时SiC颗粒的加入有效提高了复合材料的密度和硬度,对基体具有良好的强化作用。     

CuO/Al反应自生复合材料的机械性能研究

采用液态搅拌法制备了反应自生 Al2 O3增强金属基复合材料并研究了它的机械性能 .采用 X衍射和扫描电镜分析了相组成和断口形貌 .与基体合金比较 ,复合材料的强硬性得到较大提高 ,其中 10 % Cu O复合材料的抗拉强度提高了 5 2 .3% ,硬度提高近一倍 .复合材料中的拉伸断裂特征为韧性断裂 ,铸造缺陷渣气孔是主要的裂纹源     

WC/12Co颗粒增强Ni60A复合涂层的组织及耐磨性能

采用超音速等离子喷涂技术在45#钢表面制备不同配比的WC/12Co+Ni60A复合涂层.利用SEM、EDS、XRD等分析技术对该涂层的形貌特征、物相组成和微区成分进行分析,并对涂层硬度及耐磨性进行测试.结果表明:在Ni60A中添加WC/12Co颗粒可使涂层的硬度和耐磨性显著提高,当WC/12Co质量分数为30%时,复合涂层的耐磨性较Ni60A涂层的耐磨性提高10.4倍;WC/12Co+Ni60A复合涂层主要由WC增强颗粒、γ-Ni基体及基体上分布的Cr2B、Cr7C3、Ni3Si2、W2C等相组成.其中大部分未熔的WC颗粒弥散分布在γ-Ni基体上形成硬质点相,是提高涂层耐磨性的主要因素;同时WC颗粒的存在对γ-Ni基固溶体基体有强化作用,使得涂层耐磨性进一步提高.     

Cu/Ti3 AIC2复合材料的耐磨性研究

以元素单质粉Ti,Al,C,Cu为原料,采用机械合金化和放电等离子烧结(SPS),成功制备了Cu/Ti3AlC2复合材料块体,并对其进行了组织性能分析.实验结果表明:采用SPS烧结技术制备的Cu/Ti3AIC2复合材料,随着Ti3AIC2含量的增加,其显微硬度逐渐提高,相同烧结工艺条件下(900℃烧结,保温20 rain)添加15vol%Ti3AlC2复合材料的硬度比纯Cu提高近2倍;添加适量的Ti3AlC2可显著提高复合材料的耐磨性,当复合材料中含5vol%Ti3AlC2时,磨损量降低30%以上.     

(TiB_2+Al_2O_3)增强铝基复合材料的组织分析与硬度测试

将TiO2和B2O3原料混合后加入ZL102铝熔体,采用原位反应的方法,使其与铝液发生反应,制备出(TiB2+Al2O3)双相增强铝基复合材料.用EPMA及SEM分析反应合成的增强颗粒在基体上的分布状态以及TiB2和Al2O3颗粒的微观组织,用显微硬度仪测定复合材料组成相的显微硬度.结果表明,利用Al-TiO2-B2O3体系可以原位制备颗粒增强的铝基复合材料,合成的复合材料硬度比ZL102提高37.3%.     

原位合成TiB_2颗粒增韧SiC的显微组织与断裂韧性

在前期对原位生成TiB2增韧SiC制备工艺研究的基础上,研究了TiB2/SiC复合陶瓷的显微组织与力学性能.研究发现:在φ(TiB2)介于5%~20%时,原位生成的TiB2相在SiC基体中的分布都比较均匀;当φ(TiB2)为5%和20%时,TiB2颗粒等面积圆直径平均值分别为2.6和3.9μm;另外,TiB2颗粒能起到明显细化SiC晶粒的作用.随着φ(TiB2)的增加,TiB2/SiC复合材料的相对密度、维氏硬度和断裂韧性均增大.当φ(TiB2)为20%时,复合材料相对密度、维氏硬度和断裂韧性分别为94.8%,29.1 GPa和5.9 MPa.m1/2.经优化工艺制备的TiB2/SiC复合陶瓷...     

Cu／Ti3AlC2复合材料的耐磨性研究

以元素单质粉Ti,Al,C,Cu为原料,采用机械合金化和放电等离子烧结（SPS）,成功制备了Cu／Ti3AlC2复合材料块体,并对其进行了组织性能分析。实验结果表明：采用SPS烧结技术制备的Cu／Ti3AlC2复合材料,随着Ti3AlC2含量的增加,其显微硬度逐渐提高,相同烧结工艺条件下（900℃烧结,保温20min）添加15vol％Ti3AlC2复合材料的硬度比纯Cu提高近2倍;添加适量的Ti3AlC2可显著提高复合材料的耐磨性,当复合材料中含5vol％Ti3AlC2时,磨损量降低30％以上。     

镀层对金刚石/玻璃复合材料性能的影响

为满足现代电子工业日益增长的散热需求,急需研究和开发新型高导热陶瓷(玻璃)基复合材料,而改善复合材料中增强相与基体的界面结合状况是提高复合材料热导率的重要途径.本文在对金刚石和镀Cr金刚石进行镀Cu和控制氧化的基础上,利用放电等离子烧结方法制备了不同的金刚石增强玻璃基复合材料,并观察了其微观形貌和界面结合状况,测定了复合材料的热导率.实验结果表明:复合材料中金刚石颗粒均匀分布于玻璃基体中,Cu/金刚石界面和Cr/Cu界面分别是两种复合材料中结合最弱的界面;复合材料的热导率随着金刚石体积分数的增加而增加;金刚石/玻璃复合材料的热导率随着镀Cu层厚度的增加而降低,由于镀Cr层实现了与金刚石的化学结合以及Cr在Cu层中的扩散,镀Cr金刚石/玻璃复合材料的热导率随着镀Cu层厚度的增加而增加.当金刚石粒径为100μm、体积分数为70%及镀Cu层厚度为约1.59μm时,复合材料的热导率最高达到约91.0 W·m-1·K-1.     

氩弧熔敷原位自生WC复合涂层组织及耐磨性

为提高采煤机中截齿的耐磨性能,利用氩弧熔敷技术,在35CrMnSi钢表面制备WC增强Ni基复合涂层。利用OM、SEM、XRD和EDS分析复合涂层的显微组织,采用显微维氏硬度仪测试复合涂层的显微硬度,并测试涂层在室温磨损条件下的耐磨性能。结果表明：氩弧熔敷涂层组织均匀致密,熔敷涂层与基体呈冶金结合,主要由WC、W：C、T—Ni、（Fe,Cr）23,C6等物相组成;WC颗粒呈弥散分布,颗粒尺寸为1txm;熔敷涂层可以改善基体的表面硬度,最高显微硬度可达12．6GPa;熔敷涂层在室温冲击磨粒磨损实验条件下,具有优异的耐磨性,磨损机制主要是磨粒磨桶．其耐磨性较35CrMnSi基体提高近12倍。     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.