基于泵内纸浆悬浮液数值计算的纸浆泵设计

在由吸水室、前盖板、半开叶轮和涡壳组成的过流部件内，对纸浆悬浮液的流动进行了三维不可压两相湍流流动计算．计算采用双流体模型及κ-ε湍流模型，Phase Coupled SIMPLE算法进行压力速度耦合计算．根据计算结果，对两相流动的速度、压力及体积分数进行了对比和分析研究．发现在叶轮叶片数较少的情况下，叶轮流道内速度变化不均匀．并着重对前盖板与叶轮间隙内的流动进行了分析，揭示了半开式叶轮输送两相流介质的优点所在．该计算结果为建立少叶片半开式叶轮纸浆泵的设计方法提供了理论依据．根据新的设计方法设计出的纸浆泵，效率经检测高出国家标准17．5％．     

基圆对双流道叶轮压出室第Ⅰ段面流场的影响

应用CFD技术计算双流道式泵包括叶轮及压出室在内的全三维湍流场,证实基圆大小不同时泵的水力特性有不同。分析认为压出室第一断面内流场压力及速度分布显著差别是主要原因,通过对比不同基圆下的流场分布,找出影响压出室第一断面流场分布的因素。计算结果有助于深入了解双流道叶轮压出室内部流动机理,对双流道叶轮压出室的水力设计提供参考。     

轻载型轴流泵的流场分析和叶型优化

在不同工况下,采用商业软件Numeca的Fine/Turbo模块,对包含叶轮、导叶、弯管、喇叭管的轻载型轴流泵进行了全流道的三维湍流数值模拟计算,并在与已有试验数据进行了较好吻合的基础上,对其内部流场进行了详细地数值分析,通过分析轴流泵内部的流动特点,找出了造成原模型流动损失的可能原因,发现由于局部结构设计不合理,流道内产生了漩涡区。针对这一问题提出了改进措施,采用商业软件Numeca的Design3D模块对叶轮叶型压力面和吸力面进行多参数化优化。结果表明,控制压力面、吸力面型线可以有效控制叶片出口处的漩涡,改进后的流道内存在的涡团和流动损失减少,叶轮的水力效和扬程等性能参数相对提高。     

基于非定常计算的对旋风机压力脉动分析

利用Realizable k-ε湍流模型对局部对旋负机进行了全流道非定常湍流计算,预测了前后两级化附近各干涉面上压力脉动的时域分布情况。分析结果表明,前后两级叶轮之间的动-动干涉、前后两级叶轮与其相邻部件之间的动-静干涉以及流动的周期非定常特性是对旋式通风机内部压力脉 动产生的主要根源;后级叶轮叶片对叶轮区域压力脉动的影响要远大于前级叶轮。数值模拟结果可以作为对旋风机叶轮部分气动噪声预估的参考依据。     

单流道泵内部流动研究方法探讨

该文将单流道泵叶轮和涡壳作为一个整体，利用势流理论计算了单流道泵内部流动，对流场进行初步分析，得到了叶轮转至不同角度时水对叶轮的径向力以及水功率．同时，作者还利用湍流模型对单流道泵内三维湍流流动进行了数值模拟，并通过两种方法的结果比较和与实验对比以及对应用前景分析等验证了研究方法的实用性．     

分流叶片离心泵叶轮内变工况三维数值分析

对带分流叶片的离心泵叶轮不同工况下的内部流动进行数值模拟分析．计算采用雷诺时均方程和修正了的κ-ε湍流模型,在压强连接的隐式修正法建立的压力速度校正方程基础上,利用贴体坐标系和交错网格技术进行计算．计算结果揭示了带分流叶片的离心泵叶轮内部湍流流动不同工况下的速度分布及压力分布规律,对叶轮内部流动状况进行了分析和研究．结果表明：随着流量的增加,叶轮内相对速度增大明显;叶轮内整体动压随流量增加而下降,动压在叶轮内的分布场为大流量比小流量更加均匀．     

大流量下动静干涉对离心泵叶轮做功的影响

采用基于切应力输运模型(SST)的尺度自适应模拟方法对离心泵内部流场进行数值计算,研究大流量下动静干涉对内部流动的影响.从叶轮做功着手分析叶轮流道做功、流道表面做功及压力分布情况,进而分析内部流场的变化情况.数值计算结果经过试验验证及网格无关性验证,分析结果表明:在隔舌前部流速大、压力低,当叶轮流道经过该位置时,径向速度增大,流道内压力降低,此时该流道对流体做功减小;当流道旋转经过隔舌进入隔舌下游区域时,蜗壳内压力骤增,处于隔舌下游的叶轮流道过流量减小,压力增大,流道对流体做功增大.     

离心泵蜗舌区非定常流动特性

采用Navier-Stokes方程和RNG k-ε双方程湍流模型,对多工况下离心泵全流道进行了非定常流动数值模拟. 非定常计算得到的离心泵外特性与试验数据吻合较好. 在离心泵蜗舌区设置了3个监测点,计算得到了蜗舌区流体瞬态速度矢量分布,各监测点的压力、径向速度、周向速度的脉动时域特性,并对其进行了分析. 结果表明:设计工况下,蜗舌区流动比较均匀,压力和速度脉动幅度较小. 大流量工况下,在叶轮出口的射流-尾迹结构影响下,各监测点的压力和速度随叶片转动出现相应的峰值和谷值. 小流量工况下,蜗舌区内存在绕蜗舌顶端逆向流动、叶轮出口回流、蜗舌附近蜗型段内旋涡,使得流动非常复杂,流体压力和速度脉动幅度较大,压力最大值约为最小值6倍.      

离心泵内部流场的三维空化湍流的数值计算

采用Singhal等人发展的一种三维混合流体完整空化湍流模型,基于RNG的k-ε湍流模型和SIMPLEC算法,对离心泵内部的全流道三维空化流动进行定常和非定常数值模拟.根据空化流动模拟计算的结果,得到定常和非定常情况下空化余量和扬程的曲线,与实验结果进行对比,说明计算结果能够真实反映离心泵内部空化流动的性能.进而有效地预测叶轮内部流道空化发生的部位和空化流动的发展情况,分析空化余量的降低对离心泵空化性能的影响.研究结果表明,所采用的空化模型和数值计算方法能够用于离心泵在设计工况下的空化性能的计算.     

低比转速离心泵非定常空化流动特性

为了研究低比转速离心泵的空化流动特性,基于SST k-ω湍流模型和ZGB空化模型,在不同进口压力条件下对离心泵内部空化流动进行三维非定常数值模拟,研究了离心泵在发生空化时不同位置的压力脉动规律和空泡体积变化规律.结果表明:空化发生后叶轮压力脉动主频为叶频,流道进口处次频脉动幅值增长明显;空化时叶轮流道靠近叶轮出口处的压力脉动幅值增长率与叶轮流道进口处压力脉动幅值增长率相比增长更明显;空化时叶轮流道进口处的压力脉动与叶轮流道、出口及隔舌处压力脉动相比存在迟滞现象;空化过程中空泡体积的增长过程是非线性的.     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

Perspherical Approaches for Electrons in Atoms and Charged Excitons in Quantum Wells

Instead of following Fock’s expansion,we solve the Schrodinger equation for some quantum mechanical manybody systems such as electrons in atoms and charged excitons in quantum wells in a similar way in hyperspherical coordinates by expanding the wave functions into orthonormal complete basis sets of the hyperspherical hannonics(HHs)of hyperangles and generalized Laguerre polynomials(GLPs)of the hyperradius.This leads the equation to     

Advances in broadband wireless communications under high-mobility scenarios

Future mobile communication systems aim at providing very high data transmission rates, even in high-mobility scenarios such as high-speed wheel-track trains, maglev trains, highway vehicles, airplanes, guided missiles or spacecraft. A particularly important commercial application is the strong and increasing worldwide demand for high- speed broadband wireless communications （up to 574.8 km/ h test speeds or 380 km/h commercial speeds） in railways, providing data, voice and video services for applications such as onboard entertainment services to passengers, train control, train dispatch, train sensor status handling and sur- veillance. In such high-mobility scenarios, there are a number of communication challenges, including fast hand- over, location updating, high-speed channel modeling, estimation and equalization, anti-Doppler spreading tech- niques, fast power control, and dedicated network architec- ture. Because signal transmission in very high-speed scenarios will inevitably experience serious deterioration, it is imperative to develop key broadband mobile communi- cation techniques for such high-speed vehicles.     

Wuhan University Journal of Natural Sciences TOTAL CONTENTS

<正>~~     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Scale-based spatial data model for GIS

Being the primary media of geographical information and the elementary objects manipulated, almost all of maps adopt the layer-based model to represent geographic information in the existent GIS. However, it is difficult to extend the map represented in layer-based model. Furthermore, in Web-Based GIS, It is slow to transmit the spatial data for map viewing. In this paper, for solving the questions above, we have proposed a new method for representing the spatial data. That is scale-based model. In this model we represent maps in three levels: scale-view, block, and spatial object, and organize the maps in a set of map layers, named Scale-View, which associates some given scales.Lastly, a prototype Web-Based GIS using the proposed spatial data representation is described briefly.     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to