Properties of garnet-type Li6La3ZrTaO12 solid electrolyte films fabricated by aerosol deposition method

The garnet-type Li_6La_3ZrTaO_(12)(LLZT) solid electrolyte films were fabricated by aerosol deposition(AD)method.Ball-milled LLZT powder with a cubic garnet structure and a particle size of 1-2 urn was used as raw material and deposited directly on a SUS316L or a glass substrate via impact consolidation.As-deposited LLZT film has a cubic garnet structure but contains Li_2CO_3 and La_2Zr_2O_7 phases.SEM observation revealed that the film consists of LLZT particles fractured into submicron size.The impurity phase formation during AD process was caused by the local heating by the collision between LLZT particles and deposition surface and reaction with CO_2.The Li~+ ion conductivity of LLZT film was estimated to be 0.24 × 10~(-5)S cm~(-1) at room temperature.Electronic conductivity of LLZT film was confirmed to be around 10~(-12) S cm~(-1),indicating the dominant Li~+ ion conduction of LLZT film.     

Corrosion mechanism of micro-arc oxidation treated biocompatible AZ31 magnesium alloy in simulated body fluid

The rapid degradation of magnesium(Mg) based alloys has prevented their further use in orthopedic trauma fixation and vascular intervention,and therefore it is essential to investigate the corrosion mechanism for improving the corrosion resistance of these alloys. In this work, the effect of applied voltage on the surface morphology and the corrosion behavior of micro-arc oxidation(MAO) with different voltages were carried out to obtain biocompatible ceramic coatings on AZ31 Mg alloy. The effects of applied voltage on the surface morphology and the corrosion behavior of MAO samples in the simulated body fluid(SBF) were studied systematically. Scanning electron microscope(SEM) and X-ray diffractometer(XRD)were employed to characterize the morphologies and phase compositions of coating before and after corrosion. The results showed that corrosion resistance of the MAO coating obtained at 250 V was better than the others in SBF. The dense layer of MAO coating and the corrosion precipitation were the key factors for corrosion behavior. The corrosion of precipitation Mg(OH)2and the calcium phosphate(Ca–P) minerals on the surface of MAO coatings could enhance their corrosion resistance effectively. In addition, the mechanism of MAO coated Mg alloys was proposed.     

Effect of pickling processes on the microstructure and properties of electroless Ni–P coating on Mg–7.5Li–2Zn–1Y alloy

The electroless plating Ni–P is prepared on the surface of Mg–7.5Li–2Zn–1Y alloys with different pickling processes.The microstructure and properties of Ni–P coating are investigated.The results show that the Ni–P coatings deposited using the different pickling processes have a different high phosphorus content amorphous Ni–P solid solution structure,and the Ni–P coatings exhibit higher hardness.There is higher phosphorus content of Ni–P amorphous coating using 125 g/L Cr O3and 110 ml/L HNO3(w68%)than using 180 g/L Cr O3and 1 g/L KF during pre-treatment,and the coating structure is more compact,and the Ni–P coatings exhibit more excellent adhesion with substrate(Fcup to22 N).The corrosion potential of Ni–P coating is improved and exhibits good corrosion resistance.As a result,Mg-7.5Li-2Zn-1Y alloy is remarkably protected by the Ni–P coating.     

High-energy ion treatments of amorphous As40Se60 thin films for optical applic ations

The treatment of 100 MeV Ag swift-heavy ion(SHI) irradiation with five different fluences(3 1010, 1 1011, 3 1011, 1 1012, and3 1012ions/cm2) was used to design optical and structural properties of amorphous(a-) As40Se60 chalcogenide thin films. Swanepoel method was applied on transmission measurements to determine the changes in optical bandgap, Tauc parameter and linear optical parameters, i.e., linear optical absorption, extinction coefficient and linear refractive index. Dispersion of the material was determined by Wemple–DiDomenico relation.Changes in nonlinear optical parameters of third-order optical susceptibility and nonlinear refractive index were determined using semi-empirical relations. Changes in surface morphology of the films were investigated using SEM observation, which indicated that fluence 3 1012ions/cm2was upper threshold limit for these films for ion treatment. It is observed that optical bandgap reduces from 1.76 eV to 1.64 eV, and nonlinear refractive index increases from 1.31 10 10[esu] to 1.74 10 10[esu]. Linear refractive index initially increases from 2.80 to 3.52(for fluence3 1010ions/cm2) and then keeps decreasing. The observed changes in optical properties upon irradiation were explained in terms of structural rearrangements by Raman measurement. The study was compiled with the previous literature to propose SHI as an effective optical engineering technique to achieve desired changes according to the need of optical/photonic applications.     

Phase analysis of AlFe2B2 by synchrotron X-ray diffraction, magnetic and Mössbauer studies

The structural and magnetic properties of essentially phase pure AlFe_2B_2 prepared by arc melting were compared with a sample containing impurities. Analysis was carried out by means of synchrotron X-ray diffraction, magnetic measurements and M?ssbauer spectroscopy. The analysis of synchrotron X-ray diffraction data confirmed the orthorhombic structure of space group Cmmm for AlFe_2B_2 with Al_(13)Fe_4 as main impurity phase. The magnetic measurements revealed an unsaturated ferromagnetic state in AlFe_2B_2 with a transition temperature(T_c) of 286 K. Isothermal magnetization measurment at 5 K gave a saturation magnetization of 0.7 μB per Fe atom while Arrott plots establish the second order nature of ferromagnetic transition. The thermal evolution of M?ssbauer spectra confirmed the ferromagnetic nature of this material revealing an hyperfine field of 73 kOe and an isomer shift of 0.46 mm/s at 100 K. The M?ssbauer spectra of a phase pure sample was compared with the one containing impurity phases. It is suggested that the low temperature paramagnetic contribution in M?ssbauer spectra of phase pure material may have its origin in some intrinsic phenomena arising from defects or inhomogeneities in crystal structure.     

Hot corrosion behavior of nanostructured Gd2O3 doped YSZ thermal barrier coating in presence of Na2SO4 + V 2O5 molten salts

Nickel-based superalloy DZ125 was first sprayed with a NiCrAlY bond coat and followed with a nanostructured 2 mol% Gd_2O_3-4.5 mol% Y_2 O_3-ZrO_2(2 GdYSZ) topcoat using air plasma spraying(APS). Hot corrosion behavior of the as-sprayed thermal barrier coatings(TBCs) were investigated in the presence of 50 wt%Na_2SO_4 + 50 wt% V_2O_5 as the corrosive molten salt at 900 ℃ for 100 h. The analysis results indicate that Gd doped YVO_4 and m-ZrO_2 crystals were formed as corrosion products due to the reaction of the corrosive salts with stabilizers(Y_2O_3, Gd_2O_3) of zirconia. Cross-section morphology shows that a thin layer called TGO was formed at the bond coat/topcoat interface. After hot corrosion test, the proportion of m-ZrO_2 phase in nanostructured 2GdYSZ coating is lower than that of nano-YSZ coating. The result reveals that nanostructured 2GdYSZ coating exhibits a better hot corrosion resistance than nano-YSZ coating.     

Preparation of Cu（In,Ga）Se2 thin film by sputtering from Cu（In,Ga）Se2 quaternary target

Cu(In,Ga)Se2 (CIGS) thin films were prepared by directly sputtering Cu(In,Ga)Se2 quaternary target consisting of Cu:In:Ga:Se 25:17.5:7.5:50 at%. The composition and structure of CIGS layers have been investigated after annealing at 550 ℃ under vacuum and a Se-containing atmosphere. The results show that recrystallization of the CIGS thin film occurs and a chalcopyrite structure with a preferred orientation in the (112) direction was obtained. The CIGS thin film annealed under vacuum exhibits a loss of a portion of Se, while the film annealed under Se-containing atmosphere reveals compensation of Se. Several solar cells with three different absorber thicknesses were fabricated using a soda lime glass/Mo/CIGS/CdS/i-ZnO/ZnO:Al/Al grid stack structure. The highest conversion efficiency of 9.65% with an open circuit voltage of 452.42 mV, short circuit current density of 32.16 mA cm2 and fill factor of 66.32% was obtained on a 0.755 cm2 cell area.     

A single-step synthesis of nitrogen-doped graphene sheets decorated with cobalt hydroxide nanoflakes for the determination of dopamine

Nitrogen-doped reduced graphene oxide(NrGO)sheets decorated with Co(OH)_2nanoflakes were prepared by a single-step hydrothermal process.The morphological and structural characterizations of as synthesized Nr GO@Co(OH)_2nanoflakes were performed by field emission scanning electron microscopy(FESEM),EDX-mapping and X-ray diffraction(XRD).Nr GO@Co(OH)_2nanoflakes modified glassy carbon electrode(GCE)was used for electrochemical sensing of dopamine in neutral medium.The nanocomposite modified electrode showed enhanced electrochemical sensing ability for the detection of dopamine and the limit of detection(Lo D)was found to be 0.201μM with a sensitivity value of 0.0286±0.002 m A m M~(-1).Interference studies revealed that Nr GO@Co(OH)_2─GCE endow excellent selectivity for DA detection even in the presence of higher concentration of common co-existing physiological interfering analytes.Additionally,proposed sensor demonstrated excellent performance in urine samples with promising reproducibility and stability.     

Effect of La0.8Sr0.2Co0.2Fe0.8O3-δ morphology on the performance of composite cathodes

In the present work,one dimensional La0.8Sr0.2Co0.2Fe0.8O3 δ(LSCF) nanofibers with the mean diameter of about 100 nm prepared by electrospinning were deposited on Gd0.2Ce0.8O1.9(GDC) electrolyte followed by sintering to form one dimensional LSCF nanofiber cathode. And LSCF/GDC composite cathodes were formed by introducing GDC phases into LSCF nanofiber scaffold using infiltration method. The polarization resistances for the composite cathode with an optimal LSCF/GDC mass ratio of 1/0.56 are 0.27,0.14 and 0.07 Ω cm2at 650,700 and750 1C,respectively,which are obviously smaller than 2.26,0.78 and 0.29 Ω cm2of pure LSCF nanofiber cathode. And the activation energy is1.194 eV,which is much lower than that of pure LSCF nanofiber cathode(1.684 eV). These results demonstrate that the infiltration of GDC into LSCF nanofiber scaffold is an effective approach to achieve high performance cathode for solid oxide fuel cells(SOFCs). In addition,the performance of composite cathode in this work was also compared with that of our previous nanorod structured LSCF/GDC composite cathode.     

Synthesis of dental resins using diatomite and nano-sized SiO2 and TiO2

The mechanical properties of dental composites were improved by porous diatomite and nano-sized silica (OX-50) used as co-fillers.The resin composites,filled with silanized OX-50 and silanized diatomit...     

Densification behavior of mechanically milled Cu–8 at% Cr alloy and its mechanical and electrical properties

Synthesis and consolidation behavior of Cu–8 at%Cr alloy powders made by mechanical alloying with elemental Cu and Cr powders,and subsequently,compressive and electrical properties of the consolidated alloys were studied.Solid solubility of Cr in Cu during milling,and subsequent phase transformations during sintering and heat treatment of sintered components were analyzed using X-ray diffraction,scanning electron microscopy and transmission electron microscopy.The milled powders were compacted applying three different pressures(200 MPa,400 MPa and 600 MPa)and sintered in H2atmosphere at 900 1C for 30 min and at 1000 1C for 1 h and 2 h.The maximum densification(92.8%)was achieved for the sample compacted at 600 MPa and sintered for 1000 1C for 2 h.Hardness and densification behavior further increased for the compacts sintered at 900 1C for 30 min after rolling and annealing process.TEM investigation of the sintered compacts revealed the bimodal distribution of Cu grains with nano-sized Cr and Cr2O3precipitation along the grain boundary as well as in grain interior.Pinning of grain boundaries by the precipitates stabilized the fine grain structure in bimodal distribution.     

Effect of boehmite sol on the crystallization behavior and densification of mullite formed from a sol–gel precursor

Hybrid mullite sol was synthesized from an aqueous solution of aluminum nitrate (AN), aluminum isopropoxide (AIP) and tetraethylorthosilicate (TEOS), doped with boehmite sol with different ratios. Pressureless sintering of the xerogel was carried out at different temperatures in the presence of boehmite doping. The xerogel and sintered powder were characterized by FTIR, TG-DSC, XRD, SEM and bulk density. The addition of boehmite caused the formation of metaphase spinel (6Al2O3·SiO2) crystal before the appearance of mullite phase, which could lead to the formation of amorphous phase and suppress the premature formation of mullite. Both of these effects improve the densification of mullite. A maximum density about 98% of the theoretical density (TD, 3.01 g/cm3 ) of mullite could be obtained for 5 wt% boehmite addition at 1200 1C pressureless sintering.     

The enhanced corrosion resistance of UMAO coatings on Mg by silane treatment

The surface silanization was carried out on ultrasonic micro-arc oxidation(UMAO) coatings on pure magnesium using KH550 as silane coupling agent(SCA). The surface morphology, chemical bonds and corrosion resistance of the silane films were investigated by scanning electron microscope(SEM), Fourier transform infrared spectroscopy(FTIR) and electrochemical workstation, respectively. The results showed that hybrid coatings were successfully prepared on pure magnesium by UMAO-Na OH(1 mol/L, 2 mol/L, 3 mol/L)-SCA processing. The organic films with Si–O–Mg bonds are helpful for the reduction of the pores in UMAO coatings. The pores decreased with increasing Na OH concentration. Compared with single UMAO treatment, the corrosion potentials(Ecorr) of magnesium plates with UMAO-Na OH(1 mol/L,2 mol/L, 3 mol/L)-SCA treatment increased by 29 m V, 53 m V and 75 m V, respectively, meanwhile the corrosion current density(Icorr) reduced one to two orders of magnitude. It indicated that the corrosion resistance of the coatings was improved by silane treatment.     

Corrosion behavior of Mg–Y alloy in NaCl aqueous solution

The corrosion behavior of Mg–(0.25, 2.5, 5, 8 and 15)Y alloys in 3.5wt.% NaCl aqueous solution was investigated. It was found that the degree of corrosion deterioration increased with increasing immersion time up to 2 h. Corrosion modes for the alloys with low and high content of Y element were general corrosion and pitting corrosion, respective ly, and the threshold content for the corrosion mode change was 2.5% for the tested alloys. The experimental results showed that the addition of Y refined the grain of the alloy, and the distribution, i.e., continuous or not, of the Mg24Y5 phases had great effect on the corrosion rate and corrosion mode.     

Microstructure and growth kinetics of Ce and Y jointly modified silicide coatings for Nb–Ti–Si based ultrahigh temperature alloy

In order to protect Nb-Ti-Si based ultrahigh temperature alloy from oxidation, pack cementation processes were utilized to prepare Ce and Y jointly modified silicide coatings. The Ce and Y jointly modified silicide coating has a double-layer structure: a relatively thick (Nb, X)Si2 (X represents Ti, Cr and Hf elements) outer layer and a thin (Ti, Nb)5Si4 transitional layer. The pack cementation experiments at 1150 ℃ for 8 h proved that the addition of certain amounts of CeO2 and Y2O3 powders in the packs distinctly influenced the coating thickness, the contents of Si, Ce and Y in the (Nb, X)Si2 outer layers, and the density of cavities in the coatings. In order to study the effects of Ce and Y joint modification in the silicide coatings, both only Ce and only Y modified silicide coatings were also prepared for comparison. The mechanisms of the beneficial effects of Ce and Y are discussed. A pack mixture containing 1.5CeO2-0.75Y2O3 (wt%) powders was employed to investigate the growth kinetics of the Ce and Y jointly modified silicide coating at 1050, 1150 and 1250 ℃. It has been found that the growth kinetics obeyed parabolic laws and the parabolic rate constants were 109.20 mm2/h at 1050 ℃, 366.75 mm2/h at 1150 ℃ and 569.78 mm2/h at 1250 ℃, and the activation energy for the growth of the Ce and Y jointly modified silicide coating was 197.53 kJ/mol.     

Preparation, microstructure and degradation performance of biomedical magnesium alloy fine wires

With the development of new biodegradable Mg alloy implant devices, the potential applications of biomedical Mg alloy fine wires are realized and explored gradually. In this study, we prepared three kinds of Mg alloy fine wires containing 4 wt% RE(Gd/Y/Nd) and 0.4 wt% Zn with the diameter less than 0.4 μm through casting, hot extruding and multi-pass cold drawing combined with intermediated annealing process. Their microstructures, mechanical and degradation properties were investigated. In comparison with the corresponding as-extruded alloy, the final fine wire has significantly refined grain with an average size of 3–4 μm, and meanwhile shows higher yield strength but lower ductility at room temperature. The degradation tests results and surface morphologies observations indicate that Mg–4Gd–0.4Zn and Mg–4Nd–0.4Zn fine wires have similar good corrosion resistance and the uniform corrosion behavior in SBF solution. By contrast, Mg–4Y–0.4Zn fine wire shows a poor corrosion resistance and the pitting corrosion behavior.     

Sonochemical synthesis of nanostructured nickel hydroxide as an electrode material for improved electrochemical energy storage application

A facile and fast approach for the synthesis of a nanostructured nickel hydroxide(Ni(OH)_2) via sonochemical technique is reported in the present study. The X-ray diffraction results confirmed that the synthesized Ni(OH)_2 was oriented in β-phase of hexagonal brucite structure. The nanostructured Ni(OH)_2 electrode exhibited the maximum specific capacitance of 1256 F/g at a current density of 200 mA/g in 1 M KOH_((aq)). Ni(OH)_2 electrodes exhibited the pseudocapacitive behavior due to the presence of redox reaction. It also exhibited long-term cyclic stability of 85% after 2000 cycles, suggesting that the nanostructured Ni(OH)_2 electrode will play a promising role for high performance supercapacitor application.     

Mechanical and thermal properties of NpO2 using LSDAt U approach

The elastic constants,bulk modulus,shear modulus,Young’s modulus,Debye temperature,isobaric heat capacity and minimum thermal conductivity are estimated for NpO2 using plane-wave pseudopotential method within the local spin density approximation plus Hubbard U(LSDAtU) theory.The computed lattice constants are in good agreement with the available experimental results and then three independent elastic constants were computed by means of the stress–strain method.From the knowledge of the elastic constants,the values of Young’s modulus,Poisson,Debye temperature and minimum thermal conductivity are obtained and they are 218 GPa,0.288,453.5 K and0.99 Wm-1K-1,respectively.The obtained mechanical and thermal properties of NpO2 are in agreement with the previous experimental and theoretical data.Our investigations which are unobtainable from previous report can provide valuable reference in the future.     

Ti – Cu– Zr–Fe– Nb ultrafine structur e-dendrite composites with good mechanical properties and biocompat ibility

Ti-Cu-Zr-Fe-Nb ultrafine structure-dendrite composites were designed by inducing Nb and more Ti to a Ti-Cu-Zr-Fe glass-forming alloy composition and prepared by copper mold casting.The composite alloys consist of β-Ti dendrites and ultrafine-structured CuTi₂ and CuTi phases as well as a trace amount of glassy phase.The volume fraction of β-Ti dendrites increases with the increase in content of Nb which acted as the β-Ti phase stabilizer in the alloys.The composites exhibit high compressive yield strength exceeding1200 MPa,maximum strength around 1800 MPa and low Young’s modulus around 48 GPa.The plasticity of the alloys is strongly influenced by the volume fraction and morphology of the dendritic β-Ti phase,and the compressive plastic strain was enlarged from 5.9%for the 4 at%Nb alloy to 9.2%for the 8 at%Nb alloy.The preliminary cell culture experiment indicated good biocompatibility of the composite alloys free from highly toxic elements Ni and Be.These Ti-based composite alloys are promising to have potential structural and biomedical applications due to the combination of good mechanical properties and biocompatibility.     

La2O3–Al2O3 –SiO2 glass-infiltrated 3Y-TZP all-ceramic composite for the dental restora tive application

The 3 mol% yttria stabilized tetragonal zirconia polycrystals (3Y-TZP) powder had three particle size distributions, while the fine one was lower than 100 nm. The 3Y-TZP compact was prepared by dry-pressing under pressures ranged from 10 to 30 MPa and then presintered at 1250°C for 2 h. The matrix dry-pressed under the pressure of 20 MPa had a porosity of 16.7% and could be easily processed by computer aided design and computer aided manufacturing (CAD/CAM), and which had been infiltrated by the La2O3–Al2O3–SiO2 glass at 1200°C for 4 h. The flexural strength and fracture toughness of the composite were 710.7 MPa and 6.51 MPa m^1/2, respectively. The low shrinkage (0.3%) of the composite can satisfy the net-shape fabrication standard. XRD results illustrated that zirconia in the La2O3–Al2O3–SiO2 glass-infiltrated 3Y-TZP all-ceramic composite was mainly in the tetragonal phase. SEM and EDS results indicated that the pores of the matrix were almost filled by the La2O3–Al2O3 –SiO2 glass