Catalytic effect and reaction mechanism of Ti doped in NaAlH_4: A review

Catalytic effect and hydrogen reaction mechanism of Ti doped in NaAlH4 were elaborated in this paper, and current viewpoints about Ti active species in hydrogen reaction were discussed. In a further step, the possibility and practicality of the hydrogen reaction mechanism of Ti-doped NaAlH_4 were elucidated. They could be summarized as follows: while the current theory about the hydrogen reaction mecha-nism of Ti-doped NaAlH_4 should be further improved and modified, the research on Ti-doped NaAlH_4 would be a recommendable pattern for the catalyst research in other metal complex hydrides.     

Microstructure characterization and hydrogen storage properties study of Mg2Ni0.92M0.08 (M = Ti, V, Fe or Si) alloys

In the present study Mg_2Ni-type compounds alloyed independently with Ti,V,Fe and Si were successfully prepared by wet-milling followed by sintering.Although these alloyed Mg_2Ni compounds exhibited a similar hydrogen storage mechanism as that of pure Mg_2Ni,the dissolution of Ti,V or Fe into the Mg_2NiH_4lattice had a considerable catalytic effect on hydrogen desorption from additional MgH_2.The further structure investigations clearly indicated that the substitution of Ti for Ni could suppress the formation of the micro-twined low-temperature phase(LT2)and promote the formation of the high-temperature phase(HT),thus resulting in remarkably improved hydrogen desorption kinetics for the Mg_2Ni_(0.92)Ti_(0.08)–H system.     

Current Research Progress in Magnesium Borohydride for Hydrogen Storage (A review)

Hydrogen storage in solid-state materials is believed to be a most promising hydrogen-storage technology for high efficiency, low risk and low cost. Mg(BH₄)₂ is regarded as one of most potential materials in hydrogen storage areas in view of its high hydrogen capacities (14.9 ​wt% and 145–147 ​kg ​cm⁻³). However, the drawbacks of Mg(BH₄)₂ including high desorption temperatures (about 250 ​°C–580 ​°C), sluggish kinetics, and poor reversibility make it difficult to be used for onboard hydrogen storage of fuel cell vehicles. A lot of researches on improving the dehydrogenation reaction thermodynamics and kinetics have been done, mainly including: additives or catalysts doping, nanoconfining Mg(BH₄)₂ in nanoporous hosts, forming reactive hydrides systems, multi-cation/anion composites or other derivatives of Mg(BH₄)₂. Some favorable results have been obtained. This review provides an overview of current research progress in magnesium borohydride, including: synthesis methods, crystal structures, decomposition behaviors, as well as emphasized performance improvements for hydrogen storage.     

Etching mechanism of barium strontium titanate （BST） thin films in CHF_3/Ar plasma

Reactive ion etching was used to etch barium strontium titanate thin films in a CHF3/Ar plasma.BST surfaces before and after etching were analyzed by X-ray photoelectron spectroscopy to investigate the reaction ion etching mechanism,and chemical reactions had occurred between the F plasma and the Ba,Sr and Ti metal species.Fluorides of these metals were formed and remained on the surface during the etching process.Ti was almost completely removed because the TiF4 by-product is volatile.Minor quantities of Ti?F could still be detected by narrow scan X-ray photoelectron spectra,and Ti?F was thought to be present in the form of a metal-oxy-fluoride.These species were investigated from O1s spectra,and a fluoride-rich surface was formed during etching.BaF2 and SrF2 residues were difficult to remove because of their high boiling point.The etching rate was limited to 12.86 nm/min.C?F polymers were not found on the surface,indicating that the removal of BaF2 and SrF2 was important for further etching.A 1-min Ar/15 plasma physical sputtering was carried out for every 4 min of surface etching,which effectively removed remaining surface residue.Sequential chemical reaction and sputtered etching is an effective etching method for barium strontium titanate films.     

Reaction of diaminoglyoxime and cyclic azine compounds in high temperature and pressure water

Diaminoglyoxime was reacted in water at 150-400℃ and at 27.5 MPa pressure in metal Ti tubing reactor. Experimental results indicate that, diaminoglyoxime can be converted into NH-3 and CO-2, either through direct hydrolysis or through pyrolysis and polymerization, and then further hydrolysis. The possible reaction mechanism is nucleophilic addition of water.     

氢燃料内燃机NOx排放特性及机理

为深入研究氢燃料内燃机NO_x的生成机理,基于CONVERGE软件建立了三维网格耦合详细化学反应机理的氢燃料内燃机CFD仿真模型,进行了氢燃料内燃机在不同负荷下的燃烧及排放特性研究。模型的仿真结果和试验数据较为吻合。结果表明,氢气浓度增大有利于提高氢燃料内燃机的效率;NO的大量生成出现在不断升温的快速燃烧期,快速燃烧结束后NO总量不断减少,其缸内平均温度低于2 200K时NO总量趋于稳定;热NO,NNH和N_2O是NO生成最主要的路径,其中热NO路径产生的NO排放最多,其贡献率随着负荷增大而增大。NNH和N_2O路径在较低浓度时有接近25%的贡献率,而在燃空当量比为1.0时,这2种路径对NO生成的贡献率之和为负值。采用化学反应动力学方法得到了3种路径在不同负荷下对NO生成的贡献率,初步揭示了氢燃料内燃机NO_x生成的机理,为后续研究提供了理论参考。     

Improvement in hydrogen storage performance of Mg by mechanical grinding with molten salt etching Ti3C2Clx

Mg-based materials are currently a hot research topic as hydrogen storage materials due to their considerable theoretical hydrogen storage capacity. However, the kinetic performance of hydrogen absorption and desorption of Mg is too slow and requires high temperature, which seriously hinders the application of this material. MXene is a new type of two-dimensional material with significant role in improving thermodynamics and kinetics. In this experiment, a two-dimensional layered MXene containing Cl functional group was prepared by molten salt etching using the Ti-containing MAX phase as the raw material. Then different ratios of Ti₃C₂Cl_x were uniformly dispersed onto the surface of Mg by high energy ball milling. The samples were characterized by hydrogen absorption and desorption kinetics, SEM, XRD, XPS, and DSC to investigate the effect of Ti₃C₂Cl_x on the hydrogen absorption and desorption performance of Mg. The onset hydrogen absorption temperature can be reduced to room temperature and the hydrogen release temperature is reduced by 200 ​°C by doping Ti₃C₂Cl_x. And there is also 5.4 ​wt% hydrogen storage in the isothermal hydrogen absorption test at 400 ​°C. The results of DSC demonstrate that the E_a of Mg+15 ​wt% Ti₃C₂Cl_x was reduced by 12.6% compared to pristine Mg. The ΔH is almost invariable. The results of XPS show that the presence of multivalent Ti promotes electron transfer and thus improves the conversion between Mg²⁺/Mg and H⁻/H. This study provides a guideline for further improving the hydrogen absorption and desorption performance of Mg-based hydrogen storage materials.     

Enhanced hydrogen storage properties of NaBH4–Mg(BH4)2 composites by NdF3 addition

As two important members of complex hydrides, Mg(BH₄)₂ and NaBH₄ have a high gravimetric capacity (14.9 and 10.8 ​wt%, respectively). In this study, the Mg(BH₄)₂ was synthesized by the ion exchange method. Afterwards, the Mg(BH₄)₂ and NaBH₄ composites with different amounts (30, 40 and 50 ​wt%) of NdF₃ were prepared by mechanical milling. Effects of the NdF₃ on the microstructural evolution and hydrogen storage properties were investigated. The results show that NdF₃ catalyst can significantly improve the dehydrogenation kinetics of the eutectic composites of NaBH₄–Mg(BH₄)₂. The onset hydrogen desorption temperature of the composites is about 88.6 ​°C, which is about 110 ​°C lower than that of Mg(BH₄)₂ and NaBH₄ composites. Mg(BH₄)₂–NaBH₄-0.5NdF₃ composites can released 5.2 ​wt% H₂ at 250 ​°C within 30 ​min, and the dehydrogenation capacity is significantly higher than that of Mg(BH₄)₂–NaBH₄ composites. The analysis of the dehydrogenation mechanism reveals that NdF₃ takes participate in the reaction to generate NaMgF₃ to promote the dehydrogenation reaction process of the composites.     

Comparative study of oxidation ability between boron-doped diamond (BDD) and lead oxide (PbO<Subscript>2</Subscript>) electrodes

The electrochemical oxidation capabilities of two high-performance electrodes, the boron-doped diamond film on Ti (Ti/BDD) and the lead oxide film on Ti (Ti/PbO₂), were discussed. Hydroxyl radicals (·HO) generated on the electrode surface were detected by using p-nitrosodimethylaniline (RNO) as the trapping reagent. Electrochemical oxidation measurements, including the chemical oxygen demand (COD) removal and the current efficiency (CE), were carried out via the degradation of p-nitrophenol (PNP) under the galvanostatic condition. The results indicate that an indirect reaction, which is attributed to free hydroxyl radicals with high activation, conducts on the Ti/BDD electrode, while the absorbed hydroxyl radicals generated at the Ti/PbO₂ surface results in low degradation efficiency. Due to quick mineralization which combusts PNP to CO₂ and H₂O absolutely by the active hydroxyl radical directly, the CE obtained on the Ti/BDD electrode is much higher than that on the Ti/PbO₂ electrode, notwithstanding the number of hydroxyl radicals produced on PbO₂ is higher than that on the BDD surface.     

纯Ti(BH_4)_3·5NH_3的制备及储氢性能

氨合硼氢化钛是一类放氢温度适宜的高容量储氢材料,但已报道的通过球磨法制备的氨合硼氢化钛通常含有质量分数42%以上的LiCl杂质,降低了体系总含氢量的同时也为氨合硼氢化钛本征放氢性能的表征带来了困难.因此,纯氨合硼氢化钛的制备和性能表征十分必要.本文以钛酸四异丙酯、乙硼烷、四氢呋喃和NH_3为初始原料,通过先制备前驱体Ti(BH_4)_3·2THF,然后再氨化的二步反应首次成功合成纯Ti(BH_4)_3·5NH_3,并对前驱体和氨合硼氢化钛的组成、结构和放氢性能进行系统地研究.结果表明,前驱体Ti(BH_4)_3·2THF属于斜方晶系,Pbcn空间群,且在室温下能稳定存在,是制备氨合硼氢化钛的良好前驱体;纯Ti(BH_4)_3·5NH_3具有良好的放氢性能,于75℃开始放氢,至200℃释放质量分数约10%的氢气.     

Burn-resistant behavior and mechanism of Ti14 alloy

The direct-current simulation burning method was used to investigate the burn-resistant behavior of Ti14 titanium alloy. The results show that Ti14 alloy exhibits a better burn resistance than TC4 alloy (Ti–6Al–4V). Cu is observed to preferentially migrate to the surface of Ti14 alloy during the burning reaction, and the burned product contains Cu, Cu₂O, and TiO₂. An oxide layer mainly comprising loose TiO₂ is observed beneath the burned product. Meanwhile, Ti₂Cu precipitates at grain boundaries near the interface of the oxide layer, preventing the contact between O₂ and Ti and forming a rapid diffusion layer near the matrix interface. Consequently, a multiple-layer structure with a Cu-enriched layer (burned product)/Cu-lean layer (oxide layer)/Cu-enriched layer (rapid diffusion layer) configuration is formed in the burn heat-affected zone of Ti14 alloy; this multiple-layer structure is beneficial for preventing O₂ diffusion. Furthermore, although Al can migrate to form Al₂O₃ on the surface of TC4 alloy, the burn-resistant ability of TC4 is unimproved because the Al₂O₃ is discontinuous and not present in sufficient quantity.     

Ti-M分子筛合成及其性能研究

 以高硅丝光沸石(M分子筛),TiO₂粉和HClO₄为原料,水热晶化法合成Ti-M分子筛.运用FT-IR和UV-vis光谱技术表征合成的Ti-M分子筛样品的物化特性,证明了钛原子进入了M分子筛的骨架位,推测出骨架钛在Ti-M分子筛中的确存在.选择环已酮氨氧化为探针反应,考察了Ti-M对此反应的催化活性,结果表明Ti-M分子筛对环已酮氨氧化具有较好的催化性能.     

Preparation and hydrogen storage properties of nanocrystalline TiFe synthesized by mechanical alloying

In this research, the mechanism of mechanical alloying(MA) synthesis of TiFe intermetallic compound(IMC)from individual components Ti and Fe has been studied. The partition coefficient of the apparent diffusion and the reaction rate constant during MA solid-state synthesis of the TiFe intermetallic compound in a planetary ball mill have been estimated. The results indicate that the apparent diffusion coefficient is close to 10~(–11)cm~2/s that is approximately one order higher than the conventional high temperature diffusion coefficient. The reaction rate constant is close to 1.75·10~(-6). The relation between the structure and the hydrogen storage properties of MA synthesized IMC TiFe have been briefly discussed.     

Wox-Ti薄膜的电致变色性能

为了提高WOx薄膜的电致变色性能,笔者采用磁控反应溅射工艺,以纯钨和纯钛为靶材在ITO玻璃上制备Ti掺杂WOx电致变色薄膜,用薄膜的透射光谱和XRD衍射方法对掺杂后薄膜的电致变色性能和结构进行了分析,研究了Ti掺杂对WOx薄膜电致变色性能和微观结构的影响机理.实验表明:Ti掺杂不会降低WOx薄膜的致色效果,还能显著提高薄膜的循环寿命,缩短响应时间,提高记忆存储能力,XRD分析表明,掺杂Ti之后的WOx薄膜仍为非晶态,且非晶态有增强的趋势.     

Experimental and kinetic study on ignition delay times of methane/hydrogen/oxygen/nitrogen mixtures by shock tube

Ignition delay times of methane/hydrogen/oxygen/nitrogen mixtures with hydrogen amount-of-substance fractions ranging from 0–20% were measured in a shock tube facility.The ambient temperature varied from 1422 to 1877 K and the pressure was maintained at 0.4 MPa behind the reflected shock wave.The experiments were conducted at an equivalence ratio of 2.0.The fuel mixtures were diluted with nitrogen gas so that the nitrogen amount-of-substance fraction was 95%.The experimental ignition delay time of the CH4/H2 mixture decreased as the hydrogen amount-of-substance fraction increased.The enhancement of ignition by hydrogen addition was weak when the ambient temperature was >1750 K,and strong when the temperature was <1725 K.The ignition delay time of 20% H2/80% CH4 was only one-third that of 100% CH4 at 1500 K.A modified model based on GRI-Mech 3.0 was proposed and used to calculate the ignition delay times of test mixtures.The calculated results agreed with the experimental ignition delay times.Normalized sensitivity analysis showed that HO·+H2 →H·+H2O was the main reaction for the formation of the H· at 1400 K.As the hydrogen amount-of-substance fraction increased,chain branching was enhanced through the reaction H·+O2→O·+HO·,and this reduced the ignition delay time.At 1800 K,the methyl radical (H3C·) became the key species that influenced the ignition of the CH4/H2/O2/N2 mixtures,and sensitivity coefficients of the chain termination reaction 2H3C·(+M)→C2H6(+M),and chain propagation reaction HO2+H3C·→HO·+CH3O decreased,which reduced the influence of hydrogen addition on the ignition of the CH4/H2 mixtures.     

Synthesis and characterization of monoclinic TiO<Subscript>2</Subscript> nanosheets

A novel two-step method for the synthesis of monoclinic titanium oxide （i.e. TiO2（B）） nanosheets is presented in this report. The method is featured by two steps： 1） synthesis of hydrogen titanate nanosheets, followed by 2） calcination of the titanate nanosheets at elevated temperatures. The hydrogen titanate nanosheets were prepared first by autoclaving anatase TiO2 powders, obtained by air cal- cining an ethanol-gel of Ti（OH）4 at 500℃, in aqueous NaOH （10 mol/L） at 150-200℃, and then by washing with hydro- chloric acid under supersonic irradiation. While sizes of the nanosheets were found to increase with increasing the temperature of the hydrothermal treatment, the calcination at 400-500℃ of the hydrogen titanate nanosheets that were synthesized at higher autoclaving temperatures （180-200℃） produced monoclinic TiO2 nanosheets with a uniform morphology. By contrast, the same calcination of the titanate nanosheets synthesized at the autoclaving temperature 180℃ led to anatase TiO2 nanoparticles.     

Dehydrogenation and reaction pathway of Perovskite-Type NH4Ca(BH4)3

Perovskite-type borohydride, NH_4Ca(BH_4)_3, is considered as a promising hydrogen storage material due to its high gravimetric hydrogen capacity(15.7 wt%). In this work, the dehydrogenation performance and reaction pathway of NH_4Ca(BH_4)_3 have been systematically investigated. It is found that the initial decomposition temperature is only 65 °C, suggesting a low thermodynamic stability of NH4Ca(BH4)3. The desorption kinetics conducted by differential scanning calorimetry(DSC) indicates that the activation energy of decomposition is about 226.1 k J/mol. The dehydrogenation pathway of NH_4Ca(BH_4)_3 characterized by fourier-transform infrared spectroscopy(FTIR) and solid-state nuclear magnetic resonance(NMR) shows a stepwise decomposition process,in which the initial dehydrogenation is due to destabilization of H~+ in NH4 and H-in BH4 followed by the subsequent dehydrogenation steps arising from the decomposition of homologous NH_3BH_3 and the final decomposition of Ca(BH_4)_2 at a high temperature, respectively.     

Kinetics and mechanism of titanium hydride powder and aluminum melt reaction

Based on the measurement of the released hydrogen gas pressure (P_H2), the reaction kinetics between TiH₂ powder and pure aluminum melt was studied at various temperatures. After cooling the samples, the interface of TiH₂ powder and aluminum melt was studied. The results show that the 2 H P_H2-time curves have three regions; in the first and second regions, the rate of reaction conforms zero and one order, respectively; in the third region, the hydrogen gas pressure remains constant and the rate of reaction reaches zero. The main factors that control the rate of reaction in the first and second regions are the penetration of hydrogen atoms in the titanium lattice and the chemical reaction between molten aluminum and titanium, respectively. According to the main factors that control the rate of reaction, three temperature ranges are considered for the reaction mechanism:(a) 700-750℃, (b) 750-800℃, and (c) 800-1000℃. In the first temperature range, the reaction is mostly under the control of chemical reaction; at the temperature range of 750 to 800℃, the reaction is controlled by the diffusion and chemical reaction; at the third temperature range (800-1000℃), the dominant controlling mechanism is diffusion.     

Effects of the hierarchical pyrolysis polyaniline on reversible hydrogen storage of LiBH4

In this work,LiBH_4–20 wt%PP composite was prepared by ball-milling with as-synthesized hierarchical pyrolysis polyaniline(PP)and LiBH_4,and the hydrogen sorption performance as well as catalytic mechanism of the composite was studied.It is found that the onset desorption temperature of the composite decreases to 75°C,almost 235°C lower than that of the milled LiBH_4.Moreover,the composite could release 4.1 wt%H_2and rehydrogenate a total of 4.4 wt%H_2when the temperature raiseds up to 400°C,showing an outstanding reversibility,which even 3.9 wt%H_2can be kept after five cycles.Through scanning electron microscopy(SEM)observation and X-ray diffraction(XRD)analysis,we found that the PP surface forms some nanoholes after hydrogenation-dehydrogenation cycles,which leads to the confinement of some LiBH_4in the PP nanoporous structure,therefore,the hydrogen sorption kinetics and reversibility are significantly enhanced.In addition,we also found the oxygenic groups of the PP can react with LiBH_4forming LiBO_2and Li_3BO_3,where the containing Li–B–O bonds loaded in the porous structure of the PP catalyze the hydrogenation reaction of LiBH_4.     

CNa42+团簇的结构及其储氢性能研究

氢是一种理想的二次能源,它将成为化石燃料最有希望的替代能源之一,也是亟待开发的重要能源。而氢能的储存成本高,危险性大是急需解决的问题。理论上预测CNa_4~(2+)的储氢性能,通过理论分析,发现了每个CNa_4~(2+)团簇最多可与16个H2分子有效结合,获得23.5%的质量储氢密度。在B3LYP理论水平上,H2分子与CNa_4~(2+)团簇的平均相互作用能在2.107～4.948Kcal/mol之间。由于CNa_4~(2+)的质量储氢密度在7.1～23.7wt%之间,符合美国能源部的要求目标(5.5 wt%)。研究结果表明,CNa_4~(2+)在一定环境条件下可逆吸放氢性能良好,可作为潜在的理想高容量储氢材料。