Free-volume evolution of glassy Zr_(65)Al_(7.5)Ni_(10)Cu_(17.5) during inhomogeneous deformation

Free-volume evolutions of the as-cast and pre-annealed Zr65Al7.5Ni10Cu17.5 metallic glasses during cold-rolling were investigated using differential scanning calorimetry. As deformation degree increases, free volume in the glasses always increases first and then saturates above a critical strain, while the structure remains completely amorphous. The glass with less initial free volume possesses a higher increase rate of free-volume content during deformation, and as a result the free-volume contents of all the glasses approach each other at higher strains. Coalescence of free volume in shear bands into nanovoids is proposed to be responsible for the saturation of free-volume content at high strains.     

Influence of reaction stresses induced by dislocation slips on the orientation evolution in bcc metals

A plastic deformation model for bcc metals is proposed in consideration of reaction stresses.The shear strains and the corresponding reaction stresses induced by the activation of dislocations are calculated in the model,which will influence the following dislocation activation.The rolling texture in bcc metals is simulated up tp 80% reduction,whille the ratio of critcal resolved shear stresses between the dislocations slippingon the {110}and{112}planes is chosen as 0.95.The corresponding calculation is also conducted with the activation of second dislocation,if the difference between the orientation factor of the two dislocations with maximal orientation factors is lower than 5%.It is shown that the simulated texture is closer to that of the 80% rolled interstitial free steels than other modeling.It is believed that the new model can give more attention to both of the strain and stress continuities during the plastic deformation of polycrystalline metals,and therefore approaches closer to the real deformation process in bcc metals.     

Quantitative calculation for the dissipated energy of fault rock burst based on gradient-dependent plasticity

The capacity of energy absorption by fault bands after rock burst was calculated quantitatively according to shear stressshear deformation curves considering the interactions and interplaying among microstructures due to the heterogeneity of strain softening rock materials. The post-peak stiffness of rock specimens subjected to direct shear was derived strictly based on gradientdependent plasticity, which can not be obtained from the classical elastoplastic theory. Analytical solutions for the dissipated energy of rock burst were proposed whether the slope of the post-peak shear stress-shear deformation curve is positive or not. The analytical solutions show that shear stress level, confining pressure, shear strength, brittleness, strain rate and heterogeneity of rock materials have important influence on the dissipated energy. The larger value of the dissipated energy means that the capacity of energy dissipation in the form of shear bands is superior and a lower magnitude of rock burst is expected under the condition of the same work done by external shear force. The possibility of rock burst is reduced for a lower softening modulus or a larger thickness of shear bands.     

Effects of asymmetric rolling process on ridging resistance of ultra-purified 17%Cr ferritic stainless steel

In ferritic stainless steels, a significant non-uniform recrystallization orientation and a substantial texture gradient usually occur, which can degrade the ridging resistance of the final sheets. To improve the homogeneity of the recrystallization orientation and reduce the texture gradient in ultra-purified 17%Cr ferritic stainless steel, in this work, we performed conventional and asymmetric rolling processes and conducted macro and micro-texture analyses to investigate texture evolution under different cold-rolling conditions. In the conventional rolling specimens, we observed that the deformation was not uniform in the thickness direction, whereas there was homogeneous shear deformation in the asymmetric rolling specimens as well as the formation of uniform recrystallized grains and random orientation grains in the final annealing sheets. As such, the ridging resistance of the final sheets was significantly improved by employing the asymmetric rolling process. This result indicates with certainty that the texture gradient and orientation inhomogeneity can be attributed to non-uniform deformation, whereas the uniform orientation gradient in the thickness direction is explained by the increased number of shear bands obtained in the asymmetric rolling process.     

Non-equilibrium segregation of boron on grain boundary in Fe-30%Ni alloy

The moving boundary non-equilibrium segregation during recrystallization and the influence of pre-deformation in Fe-30%Ni Alloy at1000℃ was investigated by the PTA (particle tracking autoradiography) technique, optical and electron microscopy. The results indicated that intensity of boron segregation on moving boundary after different deformation is concerned with the pre-deformation degree and the movingspeed of the boundary. The TEM (transmission electron microscopy) result showed that the dislocation density nearby the moving boundary increase obviously. The phenomena are discussed by the widening grain boundary mechanism.     

Effect of Zinc additive on dielectric properties of Cd–Se glassy system

Cd5Se95–xZnx(x=0, 2, 4, 6) glassy alloy has been prepared by a melt-quenching technique. Thin films were deposited by thermal coating unit on ultraclean glass substrate under a vacuum of 10–6Torr. The absence of any sharp peaks in the X-ray diffraction confirms the amorphous nature of thin films. The frequency and temperature dependence of dielectric constant and dielectric loss in the frequency range of 1 kHz to 1 MHz and in the temperature range of 290–370 K were studied. Dielectric dispersion was observed when Zinc(Zn) was incorporated into the Cd–Se system.The increase in dielectric parameter with Zn concentration may be due to increase in defect states. The DC conductivity has been reported to investigate the effect of Zn concentration on DC conduction loss. The results are interpreted in term of dipolar theory for Cd5Se95 and Cd5Se93Zn2samples, while the remaining samples have been explained on the basis of DC conduction loss. It was also observed that the DC conductivity increased with the increase of Zinc concentration, which may be due to the decrease in the band gap near Fermi level.     

Experimental studies on the effects of porosity on acoustic resonance spectroscopy for synthetic porous rock samples in a cylindrical resonant cavity

Based on our previous work on acoustic resonance spectroscopy （ARS） measurement, the ARSs in low frequency modes were measured for 10 synthetic oil-saturated rock samples with the porosities ranging from 22% to 30%, and the effects of porosity on ARS of the synthetic porous rock samples in a cylindrical resonant cavity were studied. The experimental results show that as the location of a synthetic rock sample changes from the top to the middle of the resonant cavity, the resonance frequency （RF） will gradually increase and the corresponding resonance amplitude （RA） will decrease. In the middle of the cavity, the RF reaches its maximum, while the RA reaches its minimum. When the synthetic rock porosity increases, the RF will decrease and the RA will decrease. Furthermore, the RF of a synthetic rock sample was numerically calculated with an average volume model in the resonant cavity. Our numerical results show that as the location of the sample changes from the top to the middle of the cavity, the RF gradually increases and the RF reaches its maximum value in the middle of the cavity. However, the RF decreases as the porosity of the sample increases in the middle of the cavity. The porosity effects on the ARS described above were confirmed by our experimental result as well as the theoretical analyses, which is important for porosity and fracture characterizations in a rock sample using the ARS in a low frequency mode.     

Novel titanium particles reinforced Zr-based bulk metallic glass composites prepared by infiltration casting

A novel Ti/Zr_41.2Ti_13.8Cu_12.5Ni_10.0Be_22.5 composite was successfully prepared by infiltrating the melt into sintered Ti preform. It shows that the introduction of Ti particles into the composite results in an increase in elastic strain to 3% and an enhancement of the strength up to 2.1 GPa. High specific strength has been obtained because of the decrease in density of the composite. It is suggested that an improvement in the mechanical properties of the composite may be attributed to the generation of multiple shear bands and some deformation in the Ti particles.     

Effect of thermal deformation parameters on the microstructure,texture, and microhardness of 5754 aluminum alloy

The evolution of the microstructure, texture, and microhardness of 5754 aluminum alloy subjected to high-temperature plastic deformation under different deformation conditions was studied on the basis of thermal simulations and electron-backscattered diffraction and Vickers microhardness experiments. The results of a misorientation angle study show that an increase in the deformation temperature and strain rate promoted the transformation of low-angle grain boundaries to high-angle grain boundaries, which contributed to dynamic recrystallization. The effect of the deformation parameters on the texture and its evolution during the recrystallization process was explored on the basis of the orientation distribution function. The results demonstrate that the deformed samples mainly exhibited the features of type A, B, and B textures. The formation and growth of the recrystallized grains clearly affected the texture evolution. The microhardness results show that the variation of the microhardness was closely related to the temperature, strain rate, and dynamic recrystallization.     

Influence of intermediate annealing on the microstructure and texture of Ni-9.3at%W substrates

The effects of intermediate annealing (IA) on the microstructure and texture of Ni-9.3at%W substrates have been investigated by using electron backscattering diffraction and X-ray diffraction. Results suggest that IA can optimize the homogeneity of deformation microstructure. Higher IA temperatures (without undergoing recrystallization during IA) will increase the copper-type components of deformation texture and improve the content of cube texture after recrystallization. Sharp cube texture (97.2%) can be obtained at the optimum IA temperature of 650℃. The mechanism underlying the transition of deformation texture can be interpreted as that IA increases the dislocation slipping ability and suppresses the twinning deformation of Copper orientation in the subsequent rolling process. The observed strengthening of cube texture as a result of IA treatment is presumably attributed to the reduction of noncube nucleation and the optimization of preferential growth surrounding the cube nuclei.     

Effects of metal binder on the microstructure and mechanical properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-based micro-nanocomposite ceramic tool material

The Al₂O₃-(W,Ti)C composites with Ni and Mo additions varying from 0vol% to 12vol% were prepared via hot pressing sintering under 30 MPa. The microstructure was investigated via X-ray diffraction (XRD) and scanning electron microscopy (SEM) equipped with energy dispersive spectrometry (EDS). Mechanical properties such as flexural strength, fracture toughness, and Vickers hardness were also measured. Results show that the main phases Al₂O₃ and (W,Ti)C were detected by XRD. Compound MoNi also existed in sintered nanocomposites. The fracture modes of the nanocomposites were both intergranular and transgranular fractures. The plastic deformation of metal particles and crack bridging were the main toughening mechanisms. The maximum flexural strength and fracture toughness were obtained for 9vol% and 12vol% additions of Ni and Mo, respectively. The hardness of the composites reduced gradually with increasing content of metals Ni and Mo.     

Giant magneto-optical faraday effect of nanometer Fe-In<Subscript>2</Subscript>O<Subscript>3</Subscript> granular films

The giant magneto-optical Faraday effect of nanometer ferromagnetic metal-semiconductor matrix Fe-ln2O3 granular films prepared by the radio frequency sputtering are studied. The result shows that the Faraday rotation angle θF value of the granular film samples with Fe volume fraction x = 35% is of the order of 10^5（°）/cm at room temperature. Temperature dependence of the Faraday rotation angle θF of Fe0.35（In2O3）0.65 granular films shows that θF value below 10 K increases rapidly with the decrease of the temperature, and when T= 4.2 K, θF value is 106（°）/cm. Through the study of the dependence of low field susceptibility on temperature and the hysteresis loops at different temperatures, it has been found that when the temperature decreases to a critical point Tp = 10 K, the transformation of state from ferro-agnetic to spin-glass-like occurs in Fe0.35（In2O3）0.65 granular films. The remarkable increase of the Faraday rotation angle θF value of Fe0.35（In2O3）0.65 granular films below 10 K seems to arise from the sp-d exchange interaction of the granular film samples in the spin-glass-like state.     

Temperature effect on the corrosion and passivation characterization of Ni<Subscript>82.3</Subscript>Cr<Subscript>7</Subscript>Fe<Subscript>3</Subscript>Si<Subscript>4.5</Subscript>B<Subscript>3.2</Subscript> alloy in acidic media

The effects of temperature on corrosion and the electrochemical behavior of Ni_82.3Cr₇Fe₃Si_4.5B_3.2 glassy alloy in HCl, H₂SO₄, and H₃PO₄ acids were studied using AC and DC techniques. Impedance data reveal that the susceptibility to localized corrosion increases with increasing temperature. Potentiodynamic polarization curves reveal that the bulk glassy alloy is spontaneously passivated at all the investigated temperature in H₂SO₄ and H₃PO₄ solutions. A localized corrosion effect in HCl solution is clearly observed. The apparent activation energies in the regions of Tafel, active, and passive, as well as the enthalpies and entropies of the dissolution process were determined and discussed. The high apparent activation energy (E_a) value for H₃PO₄ solution in Tafel region is explained by the low aggressivity of PO₄3- ions.     

Effect of Ag addition on the thermal stability and glass-forming ability of Zr<Subscript>35</Subscript>Ti<Subscript>30</Subscript>Cu<Subscript>7.5</Subscript>Be<Subscript>27.5</Subscript> bulk metallic glass

The thermal stability and glass forming ability (GFA) of Zr35-xTi30Cu7.5Be27.5Agx (x = 0-10) alloys were studied by X-ray diffraction (XRD), differential scanning calorimetry (DSC) and ultrasonic techniques. We found that the addition of 1 at.% Ag can considerably enhance the GFA as indicated by an increase in the critical glass dimension from 15 mm in the Zr35Ti30Cu7.5Be27.5 alloy to 20 mm in the Zr34Ti30Cu7.5Be27.5Ag1 alloy. However, with the addition of more Ag the supercooled liquid region (△Tx) and y parameter (defined as Tx/(Tg+Tl)) drastically decreased from 155 K and 0.436 to 76 K and 0.363, respectively, resulting in a decrease in the GFA. Additionally, the elastic constant (the ratio of shear modulus to bulk modulus or Poisson’s ratio) was also used as a gauge to evaluate the GFA in Zr35-xTi30Cu7.5Be27.5Agx alloys.     

Rolling-induced microstructure change in Zr_（65）Al_（7.5）Ni_（10）Cu_（12.5）Ag_5 bulk metallic glass

The microstructures and free-volume evolutions of as-cast and pre-annealed Zr65Al7.5Ni10Cu12.5Ag5 bulk metallic glasses during rolling deformation have been investigated. No phase transformation is detected in the as-cast/rolled specimen. However,the structural stability of the glass against plastic deformation is worse after pre-annealing,indicated by nanocrystallization in preannealed/rolled specimens with large deformation degrees. Moreover,with increasing deformation degree,the free-volume content in a pre-annealed/rolled specimen increases at a lower average rate than that in an as-cast/rolled specimen.     

Shear-thinning behavior of the CaO-SiO2-CaF2-Si3N4 system mold flux and its practical application

Satisfying the mold-flux performance requirements for high-speed continuous casting necessitates the development of a new non-Newtonian-fluid mold flux with shear-thinning behavior, i.e., a mold flux whose viscosity is relatively high under lower shear rates and relatively low under higher shear rates. In this work, a mold flux that exhibits shear-thinning behavior was developed by adding different amounts of Si₃N₄ to the CaO-SiO₂-CaF₂ mold flux. The shear-thinning behavior was investigated using a rotational viscometer. In addition, the microstructure of the newly prepared slags was studied by high-temperature Raman spectroscopy and X-ray photoelectron spectroscopy. The results showed that the mechanism of shear-thinning was attributable to a temporary viscosity loss caused by the one-way shear stress, whereas the corresponding magnitude of shear-thinning was closely related to the degree of polymerization (DP). Finally, the non-Newtonian fluid mold flux was used for laboratory casting tests, which revealed that the mold flux could reduce slag entrapment and positively affect the continuous casting optimization.     

Preparation and luminescence characteristics of Sr3SiO5：Eu^2＋ phosphor for white LED

The Sr3SiO5：Eu^2＋ phosphor was synthesized by high temperature solid-state reaction. The emission spectrum of Sr3SiO5：Eu^2＋ shows two bands centered at 487 and 575 nm, which well agree with the theoretic values of emission spectrum. The excitation spectrum for 575 nm emission center has several excitation bands at 365, 418, 458 and 473 nm. And the results show that the emission spectrum of Sr3SiO5：Eu^2＋ is influenced by the Eu^2＋ concentration. The relative emission spectra of the white-emitting InGaN-based YAG：Ce^3＋ LED and Sr3SiO5：Eu^2＋ LED were investigated. The results show that the color development of InGaN-based Sr3SiO5：Eu^2＋ is better than that of InGaN-based YAG：Ce^3＋, and the CIE chromaticity of InGaN-based Sr3SiO5：Eu^2＋ is （x=0.348, y=0.326）.     

Preparation and upconversion luminescence of YVO<Subscript>4</Subscript>:Er<Subscript>3+</Subscript>, Yb<Subscript>3+</Subscript>

YVO₄:Er³⁺, Yb³⁺ with varying Yb³⁺ concentrations were prepared by a precipitation method. The results of X-ray diffraction (XRD) show that all the samples have a tetragonal zircon structure; the calculated average crystallite sizes are in the range of 14–22 nm. The lattice constants and cell volume of the samples decrease slightly with the increase in Yb³⁺ concentration. The upconversion luminescence spectra of all the samples were studied under 980 nm laser excitation. The strong green emission is observed, which is attributed to the ²H_11/2 → ⁴I_15/2 and ⁴S_3/2→⁴I_15/2 transitions of Er³⁺, and the red emission peaks in 650–675 nm can be ignored. The emission intensity for the sample depends on the Yb³⁺ concentration. These results reveal that the upconversion processes of YVO₄:Er³⁺, Yb³⁺ are related to the structure and the doping Yb³⁺ concentration of the sample.     

Synthesis and Magnetic Properties of Spin-Liquid Tb2Ti2O7

Polycrystalline samples of a novel spin-liquid compound Tb2Ti2O7 were prepared by a standard solid-state reaction. X-ray diffraction at room temperature confirms that the synthesized compound of Tb2Ti2O7 is single phase with cubic unit cell constant a0 of 1.015 44 nm. Magnetic susceptibility measurements in the temperature range between 100 and 300 K give an effective moment of 9.44 μB and Curie-Weiss temperature of 12.68 K, respectively, indicating the dominance of antiferromagnetic interactions. However, below 50 K, the magnetic behavior of Tb2Ti2O7 deviates from Curie-Weiss law, whose origin remains suspicion.     

Chemical quenching and inhibition of positronium in Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

The pore structure of Cr2O3/Al2O3 catalysts and the surface chemical properties of these pores were characterized by positron lifetime and coincidence Doppler broadening (CDB) measurements. Four lifetime components could be resolved from the positron lifetime spectrum, with two long lifetime components and two short lifetime components. The two long lifetimes τ4 and τ3 are attributed to ortho-positronium (o-Ps) annihilation in large pores and microvoids, respectively. With increasing Cr2O3 content, both τ4 and its intensity I4 show sharp decrease, while τ3 and its intensity I3 keep nearly unchanged. The Doppler broadening S parameters also show sharp decrease with increasing Cr2O3 content. Detailed analysis of the CDB spectrum reveals that the parapositronium (p-Ps) intensity also decreases with increasing Cr2O3 content. This indicates that the change of o-Ps lifetime τ4 is due to the chemical quenching by Cr2O3 but not spin-conversion of positronium. The decrease of o-Ps intensity I4 indicates that Cr2O3 also inhibits positronium formation.