Near-infrared to visible up-conversion emissions of Er^3＋ doped Al2O3 powders derived from the sol-gel method

The Er3 doped Al2O3 powders were prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)3]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)3.5H2O]. The different phase structure, including three crystalline types of (Al,Er)2O3 phases, γ, θ, α, and two Er-Al-O phases, ErAlO3 and Al10Er6O24, was obtained with the 1 mol% Er3 doped Al2O3 powders at the different sintering temperatures of 600―1200℃. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the 2H11/2, 4S3/2→4I15/2 and 4F9/2→4I15/2 transitions of Er3 , were detected by a 978 nm semiconductor laser diodes excitation. The phase structure and OH content had evident influence on the up-conversion emissions intensity. The maximum intensities of both the green and red emissions were obtained respectively for the Er3 doped Al2O3 powders sintered at 1200 ℃, which was composed mainly of α-(Al,Er)2O3, less of ErAlO3 and Al10Er6O24 phases, and with the least OH content. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er3 doped Al2O3 powders.     

Synthesis, Characterization and Calorimetry of Ni（C4H8N2O3）2Cl2

A coordination complex was synthesized from NiCl2 and dipeptide glycylglycine（GG）. It was characterized by element analysis, NMR and TG methods, and then was determined to be Ni（C4HsN2O3）2Cl2. Using an isoperibolic reaction calorimeter, the standard molar enthalpy of formation of Ni（GG）2Cl2（solid） has been determined to be -（1 674.66±2.02） kJ · mol^-1 at 298.15 K.     

Synthesis of highly ordered SnO2／Fe2O3 composite nanowire arrays by electrophoretic deposition method

Highly ordered SnO2/Fe2O3 composite nanowire arrays have been synthesized by electrophoretic deposition method. The morphology and chemical composition of SnO2/Fe2O3 composite nanowire arrays are characterized by SEM, TEM, EDX, XPS, and XRD. The results show that the SnO2/Fe2O3 composite nanowires are about 180 nm in width and tens of microns in length, and they are composed of small nanoparticles of tetraganal SnO2 and rhombohedral α-Fe203 with diameters of 10-15nm. The SnO2/Fe2O3 composite nanowires are formed by a series of chemical reactions.     

Character and fabrication of Al/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al tunnel junctions for qubit application

The superconductive Josephson junction is the key device for superconducting quantum computation. We have fabricated Al/Al2O3/Al tunnel junctions using a double angle evaporation method based on a suspended shadow mask. The Al2O3 junction barrier has been formed by introducing pure oxygen into the chamber during the fabrication process. We have adjusted exposure conditions by changing either the oxygen pressure or the oxidizing time during the formation of tunnel barriers to control the critical current density Jc and the junction specific resistance Rc. Measurements of the leakage in Al/Al2O3/Al tunnel junctions show that the devices are suitable for qubit applications.     

Synthesis and Magnetic Properties of Spin-Liquid Tb2Ti2O7

Polycrystalline samples of a novel spin-liquid compound Tb2Ti2O7 were prepared by a standard solid-state reaction. X-ray diffraction at room temperature confirms that the synthesized compound of Tb2Ti2O7 is single phase with cubic unit cell constant a0 of 1.015 44 nm. Magnetic susceptibility measurements in the temperature range between 100 and 300 K give an effective moment of 9.44 μB and Curie-Weiss temperature of 12.68 K, respectively, indicating the dominance of antiferromagnetic interactions. However, below 50 K, the magnetic behavior of Tb2Ti2O7 deviates from Curie-Weiss law, whose origin remains suspicion.     

Nonlinear optical properties of Eu<Subscript>2</Subscript>O<Subscript>3</Subscript> doped 5ZnO-20Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>-75TeO<Subscript>2</Subscript> glasses

The third-order optical nonlinearities, including third-order nonlinear susceptibility X^(3), nonlinear refractive index (n2) and temporal response, were measured with forward DFWM using Nd:YAG mode-locked pulse laser. The results show that Eu203 doped 5ZnO-20Nb2O5-75TeO2 glasses have large n2 and ultra-fast temporal response. Raman spectra show that Eu2O3 dopant induces the changes in the local structure of glasses. The higher the dopant concentration, the larger the nonlinear refractive n2 and the faster the temporal response. The enhancement on the third-order optical nonlinearities can be attributed to the deformation of the electronic clouds in [TeO4] enhanced by Eu2O3 dopant.     

Analysis of the factors affecting the magnetic characteristics of nano-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> particles

We prepared Fe3O4 nanoparticles using chemical coprecipitation and studied the factors affecting the magnetic characteristics of nano-Fe3O4 particles.We identified four factors and three levels of an orthogonal experiment and investigated these four factors that affect the magnetic characteristics of the Fe3O4 particles.We obtained important information from this investigation.The Fe3+ to Fe2+ molar ratio,the iron precursor salt,the amount of surfactant and the amount of alkali were found to be important.We also studied the influence of the order of alkali and surfactant addition,the aging time and the stirring speed on the magnetic characteristics of the nano-Fe3O4 particles.The Fe3O4 preparation process was also analyzed.     

Giant magneto-optical faraday effect of nanometer Fe-In<Subscript>2</Subscript>O<Subscript>3</Subscript> granular films

The giant magneto-optical Faraday effect of nanometer ferromagnetic metal-semiconductor matrix Fe-ln2O3 granular films prepared by the radio frequency sputtering are studied. The result shows that the Faraday rotation angle θF value of the granular film samples with Fe volume fraction x = 35% is of the order of 10^5（°）/cm at room temperature. Temperature dependence of the Faraday rotation angle θF of Fe0.35（In2O3）0.65 granular films shows that θF value below 10 K increases rapidly with the decrease of the temperature, and when T= 4.2 K, θF value is 106（°）/cm. Through the study of the dependence of low field susceptibility on temperature and the hysteresis loops at different temperatures, it has been found that when the temperature decreases to a critical point Tp = 10 K, the transformation of state from ferro-agnetic to spin-glass-like occurs in Fe0.35（In2O3）0.65 granular films. The remarkable increase of the Faraday rotation angle θF value of Fe0.35（In2O3）0.65 granular films below 10 K seems to arise from the sp-d exchange interaction of the granular film samples in the spin-glass-like state.     

Catalysis of organic pollutant photodegradation by metal phthalocyanines immobilized on TiO<Subscript>2</Subscript>@SiO<Subscript>2</Subscript>

A TiO2@SiO2 hybrid support was prepared by the sol-precipitation method using n-octylamine as a template.The photocatalyst manganese phthalocyanine tetrasulfonic acid (MnPcS) was immobilized on the support to form MnPcS-TiO2@SiO2.X-ray diffraction (XRD) and UV-Visible diffuse reflectance spectra (UV-Vis DRS) were employed to characterize the catalyst.The photocatalytic degradation of rhodamine B (RhB) and the catalytic oxidation of o-phenylenediamine (OPDA) under visible light irradiation were used as probe reactions.The mineralization efficiency and the degradation mechanism were evaluated using chemical oxygen demand (COD Cr) assays and electron spin resonance (ESR),respectively.RhB was efficiently degraded by immobilized MnPcS-TiO2@SiO2 under visible light irradiation.Complete decolorization of RhB occurred after 240 min of irradiation and 64.02% COD Cr removal occurred after 24 h of irradiation.ESR results indicated that the oxidation process was dominated by the hydroxyl radical (·OH) and superoxide radical (O-·2) generated in the system.     

Electrical conductivity optimization of the Na3AlF6-Al2O3-Sm2O3 molten salts system for Al-Sm intermediate binary alloy production

Metal Sm has been widely used in making Al-Sm magnet alloy materials. Conventional distillation technology to produce Sm has the disadvantages of low productivity, high costs, and pollution generation. The objective of this study was to develop a molten salt electrolyte system to produce Al-Sm alloy directly, with focus on the electrical conductivity and optimal operating conditions to minimize the energy consumption. The continuously varying cell constant (CVCC) technique was used to measure the conductivity for the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ electrolysis medium in the temperature range from 905 to 1055℃. The temperature (t) and the addition of Al₂O₃ (W(Al₂O₃)), Sm₂O₃ (W(Sm₂O₃)), and a combination of Al₂O₃ and Sm₂O₃ into the basic fluoride system were examined with respect to their effects on the conductivity (κ) and activation energy. The experimental results showed that the molten electrolyte conductivity increases with increasing temperature (t) and decreases with the addition of Al₂O₃ or Sm₂O₃ or both. We concluded that the optimal operation conditions for Al-Sm intermediate alloy production in the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ system are W(Al₂O₃) + W(Sm₂O₃)=3wt%, W(Al₂O₃):W(Sm₂O₃)=7:3, and a temperature of 965 to 995℃, which results in satisfactory conductivity, low fluoride evaporation losses, and low energy consumption.     

Preparation and radar-absorbing properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> composite powder

Al₂O₃/TiO₂/Fe₂O₃/Yb₂O₃ composite powder was synthesized via the sol-gel method. The structure, morphology, and radar-absorption properties of the composite powder were characterized by transmission electron microscopy, X-ray diffraction analysis and RF impedance analysis. The results show that two types of particles exist in the composite powder. One is irregular flakes (100-200 nm) and the other is spherical Al₂O₃ particles (smaller than 80 nm). Electromagnetic wave attenuation is mostly achieved by dielectric loss. The maximum value of the dissipation factor reaches 0.76 (at 15.68 GHz) in the frequency range of 2-18 GHz. The electromagnetic absorption of waves covers 2-18 GHz with the matching thicknesses of 1.5-4.5 mm. The absorption peak shifts to the lower-frequency area with increasing matching thickness. The effective absorption band covers the frequency range of 2.16-9.76 GHz, and the maximum absorption peak reaches -20.18 dB with a matching thickness of 3.5 mm at a frequency of 3.52 GHz.     

Mineral-phase evolution and sintering behavior of MO-SiO2-Al2O3-B2O3 (M=Ca,Ba) glass-ceramics by low-temperature liquid-phase sintering

In this work, network former SiO₂ and network intermediate Al₂O₃ were introduced into typical low-melting binary compositions CaO·B₂O₃, CaO·2B₂O₃, and BaO·B₂O₃ via an aqueous solid-state suspension milling route. Accordingly, multiple-phase aluminosilicate glass-ceramics were directly obtained via liquid-phase sintering at temperatures below 950℃. On the basis of liquid-phase sintering theory, mineral-phase evolutions and glass-phase formations were systematically investigated in a wide MO-SiO₂-Al₂O₃-B₂O₃ (M=Ca, Ba) composition range. The results indicate that major mineral phases of the aluminosilicate glass-ceramics are Al₂₀B₄O₃₆, CaAl₂Si₂O₈, and BaAl₂Si₂O₈ and that the glass-ceramic materials are characterized by dense microstructures and excellent dielectric properties.     

Synthesis and modification of well-ordered layered cathode oxide LiNi<Subscript>2/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript>

Oxalic-acid-based co-precipitation method was employed to prepare LiNi_2/3Mn_1/3O₂ sample with a high-ordered structure. Li⁺, Ni²⁺ and Mn²⁺ acetates were used as starting materials. The influence of the amount of lithium source in the starting materials on Li⁺ content, disorder of Li⁺-Ni²⁺ ions, and electrochemical performance has been investigated. Rietveld refinement shows that the sample prepared with 20% excess Li-source in the starting materials exhibits a perfect ordered structure. A specific discharge capacity is as high as 172 mAh/g at C/20 in the voltage range of 4.35–2.7 V. However, the cyclability is not satisfactory: about 25.3% fade in capacity was observed over 50 cycles. Chemically stable SiO2 was coated on the surface of LiNi_2/3Mn_1/3O₂ particles. A significant improvement in cyclability was attained with 3 wt% SiO2 coating, which is ascribable to the protection of LiNi_2/3Mn_1/3O₂ particles from being dissolved into the electrolyte.     

Synthesis of LiCo<Subscript>0.3</Subscript>Ni<Subscript>0.7</Subscript>O<Subscript>2</Subscript> as cathode materials for lithium ion batteries by citric acid-assisted sol-gel method

The synthesis process of LiCo0.3Ni0.7O2 was investigated by FT-IR, mass spectroscopy, elemental analysis, SEM, BET, TG/DTA and XRD in this paper. The results revealed that lithium and transition metal ions were trapped homogeneously on an atomic scale throughout the precursor. Li2CO3, NiO and CoO are the intermediate products obtained after decomposition of the precursor and Li2CO3 undergoes direct reactions with NiO and CoO to form LiCo0.3Ni0.7O2. Moreover, the kinetics of formation of LiCo0.3Ni0.7O2 by dtrate sol-gel method is faster than the case of the conventional solid-state reaction between lithium carbonate and corresponding reactants. The single phase of LiCo0.3Ni0.7O2 was synthesized at temperature as low as 550℃. The discharge capacity of LiCo0.3Ni0.7O2 increases from 127 to 185 mAh/g as the caldnation temperature increasing from 550 to 750℃. After 100 cycles, the discharge capacity of the sample calcined at 750℃ is 155 mAh/g. The electrochemical study shows that the LiCo0.3Ni0.7O2 has high discharge capacity and good cycling behavior for lithium ion batteries.     

Influence of post-annealing on the properties of Ta-doped In<Subscript>2</Subscript>O<Subscript>3</Subscript> transparent conductive films

Ta-doped In₂O₃ transparent conductive oxide films were deposited on glass substrates using radio-frequency (RF) sputtering at 300°C. The influence of post-annealing on the structural, morphologic, electrical and optical properties of the films was investigated using X-ray diffraction, field emission scanning electron microscopy, Hall measurements and optical transmission spectroscopy. The obtained films were polycrystalline with a cubic structure and were preferentially oriented in the (222) crystallographic direction. The lowest resistivity, 5.1×10⁻⁴ Ω cm, was obtained in the film annealed at 500°C, which is half of that of the un-annealed film (9.9×10⁻⁴ Ω cm). The average optical transmittance of the films was over 90%. The optical bandgap was found to decrease with increasing annealing temperature.     

Novel approaches to produce Al2O3– TiC/TiCN– Fecomposite powders directly from ilmenite

Al2O3 –TiC/TiCN–Fe composite powders were successfully prepared directly from ilmenite at 1300–1400℃.The effects of Al/C ratio,sintering atmosphere,and reaction temperature and time on the reaction products were investigated.Results showed that the nitrogen atmosphere was bene cial to the reduction of ilmenite and the formation of Al2O3 –TiC/TiCN–Fe composite powders.When the reaction temperature was between 600 and 1100℃,the intermediate products,TiO2,Ti3O5 and Ti4O7 were found,which changed to TiC or TiCN at higher temperature.Al/C ratio was found to affect the reaction process and synthesis products.When Al addition was 0.5 mol,the Al2O3 phase did not appear.The content of carbon in TiCN rose when the reaction temperature was increased.     

Electro-deoxidation of V<Subscript>2</Subscript>O<Subscript>3</Subscript> in molten CaCl<Subscript>2</Subscript>-NaCl-CaO

The electro-deoxidation of V₂O₃ precursors was studied. Experiments were carried out with a two-terminal electrochemical cell, which was comprised of a molten electrolyte of CaCl₂ and NaCl with additions of CaO, a cathode of compact V₂O₃, and a graphite anode under the potential of 3.0 V at 1173 K. The phase constitution and composition as well as the morphology of the samples were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). 3 g of V₂O₃ could be converted to vanadium metal powder within the processing time of 8 h. The kinetic pathway was investigated by analyzing the product phase in samples prepared at different reduction stages. CaO added in the reduction path of V₂O₃ formed the intermediate product CaV₂O₄.     

Microwave sintering of Ca<Subscript>0.6</Subscript>La<Subscript>0.2667</Subscript>TiO<Subscript>3</Subscript> microwave dielectric ceramics

Ca_0.6La_0.2667TiO₃ ceramics were prepared by conventional and microwave sintering techniques and their sinterability, microstructure, and microwave dielectric properties were investigated in detail for comparison. Densified Ca_0.6La_0.2667TiO₃ ceramics were obtained by microwave sintering at 1350°C for 30 min and by conventional sintering at 1450°C for 4 h. An unusual phenomenon was found that some larger grains (grain size range: 8–10 μm) inclined to assemble in one area but some smaller ones (grain size range: 2–4 μm) inclined to gather in another area in the microwave sintered ceramics. The microwave dielectric properties of Ca_0.6La_0.2667TiO₃ ceramics prepared by microwave sintering at 1350°C were as follows: dielectric constant (ɛ _r) = 119.6, quality factor (Qf) = 17858.5 GHz, and temperature coefficient of resonant frequency (τ _f) = 155.5 ppm/°C. In contrast, the microwave dielectric properties of the ceramics prepared by conventional sintering at 1450°C were ɛ _r = 117.4, Qf = 13375 GHz, and τ _f = 217.2 ppm/°C.     

Effects of Yb^3＋ codoping on visible and near infrared emissions of Er^3＋-Yb^3＋ codoped Al2O3 powders by the sol-gel method

The 0.1 mol% Er^3＋ and 0-2 mol% Yb^3＋ codoped Al2O3 powders were prepared by the sol-gel method, and the phase structure, including only two crystalline types of doped Al2O3 phase, γ-（Al,Er, Yb）2O3 and θ-（Al,Er, Yb）2O3, was detected at the sintering temperature of 1000℃. The visible and near infrared emissions properties depended strongly on the Yb^3＋ codoping, and the corresponding maximal peak intensities centered at about 523, 545, 660 and 1533 nm were obtained respectively for the 0.1 mol% Er^3＋ and 0.5 mol% Yb^3＋ codoped Al2O3 powders, which were composed of θ-（Al,Er,Yb）2O3 and a small amount of γ-（Al,Er, Yb）2O3 phases. The two-photon absorption process was responsible for the visible up-conversion emissions, and the one-photon absorption process was involved in the near infrared emissions of the Er^3＋-yb^3＋ codoped Al2O3 powders.     

Synthesis and characterization of wormhole-like mesoporous Ce0.6Zr0.35Y0.05O2 solid solutions

Nanoparticles of Ce0.6Zr0.35Y0.05O2 (CZY) solid solution have been prepared by the CTAB (hexadecyl-trimethyl ammonium bromide), CTAB-EG (ethylene glycol) templating, and CTAB-EG-NaCl (in which the pores of the precursor synthesized by the CTAB-EG method is filled by a certain amount of NaCl) method, respectively. The physical properties of these materials were characterized by means of tech-niques such as X-ray diffraction (XRD), high resolution scanning electron microscopy (HRSEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), and N2 adsorp-tion-desorption measurements. The CZY samples synthesized by the above three methods display wormhole-like mesoporous morphology and cubic crystal structures. The materials are narrow in pore size distribution (averaged pore diameter = 5.3―7.1 nm), high in surface areas (95―119 m2/g), and large in pore volumes (0.16―0.18 cm3/g). It has been demonstrated that the introduction of NaCl is capable of retaining the pore structures of solid nanomaterials at high-temperature calcination.