V、Ta微合金化12Cr低活性F/M钢的优化设计

采用Thermo-Calc热力学模拟计算与实验相结合的方法,优化设计了一种V、Ta微合金化的低活性F/M钢12Cr3WVTa,经1 050℃水淬及780℃回火后对其显微组织及析出相进行光学显微镜、扫描电镜和透射电镜观察以及能谱分析.实验钢淬火回火后显微组织由回火马氏体和少量δ铁素体相组成,析出相主要为M23C6和MX相(M=V,Ta;X=C,N),其中M23C6主要分布于回火马氏体板条界和相界,而MX弥散析出于回火马氏体板条内以及δ铁素体内.实验钢室温和高温(600℃)拉伸力学性能良好,600℃下材料抗拉强度为507 MPa,屈服强度为402 MPa,满足超临界水冷堆用包壳管的拉伸性能要求.     

淬火水温对2219铝合金锻环组织和力学性能的影响

采用室温拉伸测试、金相显微镜、扫描电镜以及透射电镜等测试分析方法,研究淬火水温(20～80℃)对2219铝合金锻环组织和拉伸性能的影响.研究结果表明:随着淬火水温提高,锻环的抗拉强度、屈服强度和延伸率先升高后降低.当淬火水温超过60℃时,锻环延伸率各向异性倾向显著增加,其主要原因是形成粗大晶界析出相.当淬火水温为40℃时,锻环具有较好的强度和延伸率,其轴向抗拉强度、屈服强度和延伸率分别为418 MPa、300 MPa和9.3%,径向抗拉强度、屈服强度和延伸率分别为420 MPa、300 MPa和9.8%,切向抗拉强度、屈服强度和延伸率分别为447 MPa、329 MPa和12.6%.     

超高强度冷轧双相钢组织与性能

在Gleeble-3500热模拟试验机上进行冷轧超高强度双相钢的连续退火工艺研究,利用光学显微镜、扫描电镜、透射电镜和拉伸试验研究了连续退火过程中各个参数对1 000 MPa级冷轧双相钢组织性能的影响.结果表明:试验用钢在退火温度800℃下保温80 s,可以得到抗拉强度为1030MPa、延伸率为14%超高强双相钢;随着退火温度的升高,屈服强度和抗拉强度降低.当退火温度为830℃时,显微组织中粒状的非马氏体组织明显增多.过时效温度低于300℃时,屈服强度和抗拉强度变化不大;当过时效温度超过300℃时,抗拉强度急剧下降,屈服强度先降低后升高,在过时效温度为360℃时开始出现屈服平台.     

钼微合金化低碳钢的显微组织与力学性能

借助物理模拟系统采用四种不同的多道次变形及控制冷却工艺,研究了成分为0.12C-0.78Si-1.42Mn-0.74Al-0.32Mo钢的显微组织和力学性能.结果显示:使用物理模拟系统进行高温区的多道次热连轧,并结合控制冷却处理,能够得到不同的复相组织(铁素体/贝氏体组织,贝氏体/马氏体组织).依贝氏体含量和形态的不同,铁素体/贝氏体复相组织钢的屈服强度为388~558MPa,抗拉强度为681~838 MPa,总延伸率为15%~27%;贝氏体/马氏体复相组织钢的屈服强度为746 MPa,抗拉强度为960 MPa,总延伸率为19%.     

Fe-Mn-1.6 Ni-C水电用钢板轧后 直接淬火和回火工艺

通过Fe-Mn-1.6Ni-C钢板控制轧制、轧后直接淬火和560~710℃回火调质处理实验,研究了轧后直接淬火态和回火态的组织与性能变化.结果表明,轧后直接淬火得到组织细小的板条马氏体,固溶强化作用提高了其抗拉强度.经过回火热处理后,碳化物的析出及其对位错的钉扎作用,降低了钢的抗拉强度,提高了钢的屈服强度.随着回火温度的升高,碳化物聚集长大,铁素体发生回复与再结晶,造成强度下降以及冲击韧性提高.当回火温度高于A_○c1时,粗大的碳化物极易引起裂纹形核,破坏钢的冲击韧性.Fe-Mn-1.6Ni-C钢最优的回火温度为680℃,屈服强度为963MPa,抗拉强度为988MPa,延伸率为20.0%,-60℃冲击功为142J.     

不同工艺低碳Nb-B贝氏体钢组织性能

对一种不添加其他微合金元素的低碳Nb-B微合金贝氏体钢在不同工艺的组织和力学性能进行研究.结果表明,终轧温度为850℃,冷却速度10℃/s左右,终冷温度560℃时,实验钢的屈服强度和抗拉强度分别为495和720MPa,-20℃冲击功和延伸率分别为159 J和23%,实验钢组织为粒状贝氏体和准多边形铁素体;终冷温度降至480℃,实验钢组织为粒状贝氏体,屈服强度和-20℃冲击功分别提高51 MPa和93 J;终轧温度降至810℃时,屈服强度相对增加24MPa;冷却速度增大到25℃/s,组织为粒状贝氏体、少量的针状铁素体和板条贝氏体,屈服强度和抗拉强度分别为655和777 MPa,而-20℃冲击功和...     

时效对10Ni10Mn2CuAl钢组织及性能的影响

基于富Cu相和NiAl(Mn)相复合沉淀析出强化的方式设计了一种新型高强度舰船用钢10Ni10Mn2CuAl,探究了时效处理工艺对10Ni10Mn2CuAl钢的组织及性能的影响.采用Thermo-Calc软件对析出相析出温度和含量进行理论计算,采用光学显微镜、扫描电子显微镜(SEM)对基体典型夹杂及对时效处理后组织进行了分析,并进行了性能测试.研究结果表明:钢中富Cu相析出温度区间为300~606℃,最高质量分数为1.41%.随时效时间增加,马氏体板条呈现粗化到细化演变,硬度增加到峰值后趋于稳定.随时效温度升高加速析出相析出过程,硬度达到峰值的时间缩短.在最佳热处理工艺下(500℃时效24h),实验钢屈服强度为1435.51MPa,抗拉强度为1555.42MPa,延伸率为8%,综合性能达到最优.     

700 MPa级Ti-Nb-V-Mo复合微合金化高强钢的工业研制

基于CSP工艺,采用Ti基复合微合金技术、控轧控冷及平整工艺,开发了屈服强度700 MPa级别的薄规格高强钢,借助SEM、TEM、EDS和力学性能测试等,分析了不同轧制工艺参数对高强钢性能、组织及析出物的影响。结果表明,该高强钢组织由准多边形铁素体及极少量粒状珠光体构成;薄规格强化及冷却速度控轧的细晶强化、卷取温度控制的析出强化共同决定了钢的组织和力学性能;高温大压下、头部连续冷却有利于薄规格细晶强化,高温(890±20℃)终轧、高温(620±20℃)卷取有利于析出大量尺寸20 nm以下且弥散分布细小的以含Ti为主的(Ti, Nb, Mo)C粒子,析出强化作用明显。与平整前相比,热轧带卷平整后钢屈服强度提高约30 MPa、抗拉强度提高约10 MPa、延伸率降低了7.9%～16.7%。     

汽车用高强度Q&P钢的组织与力学性能

研究了0.21C--1.43Si--1.35Mn钢在两相区及完全奥氏体区采用QP(Quenching and Partitioning)工艺加热后的微观组织与力学性能.结果表明:两相区加热可获得马氏体、残余奥氏体和铁素体组织,钢的抗拉强度为1 013 MPa,延伸率为25%,强塑积为25 655 MPa.%;完全奥氏体区加热可获得马氏体和残余奥氏体组织,钢的抗拉强度为1 257 MPa,延伸率为17%,强塑积为21 454 MPa.%;QP钢中的马氏体主要为板条状,伴有大量位错,并且发现有少量孪晶马氏体,分析认为由配分过程后的淬火过程转变而来;通过QP工艺可得到体积分数高达10.67%的残余奥氏体,分布在板条马氏体间,呈薄膜状.     

调质低碳贝氏体钢的组织和性能

研究了C--Mn--Mo--Cu--Nb--Ti--B系低碳微合金钢915℃淬火和490～640℃回火的调质工艺对钢的组织及力学性能的影响.用扫描电镜和透射电镜对实验钢的组织、析出物形态和分布以及断口形貌进行观察,采用X射线衍射仪分析钢中残余奥氏体的体积分数.结果表明:调质后,实验钢获得贝氏体、少量马氏体及残余奥氏体复相组织,贝氏体板条宽度只有250 nm,残余奥氏体的体积分数随着回火温度的升高而降低,经淬火与520℃回火后残余奥氏体的体积分数为2.1%.调质后析出物的数量激增,6～15 nm的析出物占70%以上.实验钢经过915℃淬火与520℃回火后,其屈服强度达到915 MPa,抗拉强度990 MPa,-40℃冲击功为95 J.细小的析出物及窄的板条提高了钢的强度.板条间有残余奥氏体存在,改善了实验钢的韧性.     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Lower Paleozoic oil relationships within Williston Basin, Canada

The Williston Basin is a significant petroleum province, containing oil production zones that include the Middle Cambrian to Lower Ordovician, Upper Ordovician, Middle Devonian, Upper Devonian and Mississippian and within the Jurassic and Cretaceous. The oils of the Williston Basin exhibit a wide range of geochemical characteristics defined as "oil families", although the geochemical signature of the Cambrian Deadwood Formation and Lower Ordovician Winnipeg reservoired oils does not match any "oil family". Despite their close stratigraphic proximity, it is evident that the oils of the Lower Palaeozoic within the Williston Basin are distinct. This suggests the presence of a new "oil family" within the Williston Basin. Diagnostic geochemical signatures occur in the gasoline range chromatograms, within saturate fraction gas chromatograms and biomarker fingerprints. However, some of the established criteria and cross-plots that are currently used to segregate oils into distinct genetic families within the basin do not always meet with success, particularly when applied to the Lower Palaeozoic oils of the Deadwood and Winnipeg Formation.     

An Analysis of Catherine＇s Character——Wuthering Heights

Wuthering Heights, Emily Bronte＇s only novel, was published in December of 1847 under the pseudonym Ellis Bell. The book did not gain immediate success, but it is now thought one of the finest novels in the English language. Catherine is the key character of this masterpiece, because everybody and everything center on her though she had a short life. We can understand this masterpiece better if we know Catherine well.     

Features of Women's language

Language is a means of verbal communication. People use language to communicate with each other. In the society, no two speakers are exactly alike in the way of speaking. Some differences are due to age, gender, statue and personality. Above all, gender is one of the obvious reasons. The writer of this paper tries to describe the features of women＇s language from these perspectives： pronunciation, intonation, diction, subjects, grammar and discourse. From the discussion of the features of women＇s language, more attention should be paid to language use in social context. What＇s more, the linguistic phenomena in a speaking community can be understood more thoroughly.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

Design and analysis of generic LBS application developing platform

Location based services is promising due to its novel working style and contents.A software platform is proposed to provide application programs of typical location based services and support new applications developing efficiently. The analysis shows that this scheme is easy implemented, low cost and adapt to all kinds of mobile nework system.     

橡胶颗粒沥青混合料低温抗裂性试验研究

以AC-13级配为基础,将橡胶颗粒代替部分集料掺入混合料中,以低温弯曲试验为评价方法对不同橡胶颗粒掺量下沥青混合料的低温抗裂性进行研究,并引入应变能密度值对混合料的低温抗裂性进行综合评价.试验结果表明:橡胶颗粒沥青混合料试件的破坏微应变均超过2 300,满足冬寒区的技术指标;无论是否掺加橡胶颗粒,随着温度的下降,沥青混合料破坏时的最大弯拉强度增大,弯拉应变降低,劲度模量增大;弯曲应变能密度在胶粒掺量为1%左右时具有较大的弯曲应变能密度值,此时橡胶颗粒沥青混合料具有较好的低温抗裂性.     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

Quantitative trait loci （QTLs） for quality traits related to protein and starch in wheat

Quality traits in wheat （Triticum aestirum L.） were studied by quantitative trait locus （QTL） analysis in a recombinant inbred line （RIL） population, a set of 131 lines derived from Chuan 35050 × Shannong 483 cross （ChSh）. Grains from RILs were assayed for 21 quality traits related to protein and starch. A total of 35 putative QTLs for 19 traits with a single QTL explaining 7.99-40.52% of phenotypic variations were detected on 10 chromosomes, 1D, 2A, 2D, 3B, 3D, 5A, 6A, 6B, 6D, and 7B. The additive effects of 30 QTLs were positive, contributed by Chuan 35050, the remaining 5 QTLs were negative with the additive effect contributed by Shannong 483. For protein traits, 15 QTLs were obtained and most of them were located on chromosomes 1 D, 3B and 6D, while 20 QTLs for starch traits were detected and most of them were located on chromosomes 3D, 6B and 7B. Only 7 QTLs for protein and starch traits were co-located in three regions on chromosomes 1D, 2A and 2D. These protein and starch trait QTLs showed a distinct distribution pattern in certain regions and chromosomes. Twenty-two QTLs were clustered in 6 regions of 5 chromosomes. Two QTL clusters for protein traits were located on chromosomes 1D and 3B, respectively, three clusters for starch traits on chromosomes 3D, 6B and 7B, and one cluster including protein and starch traits on chromosome 1D.     

On Tragic Consciousness In The Works By Ernest Hemingway

As an American modern novelist who were famous in the literary world, Hemingway was not a person who always followed the trend but a sharp observer. At the same time, he was a tragedy maestro, he paid great attention on existence, fate and end-result. The dramatis personae's tragedy of his works was an extreme limit by all means tragedy on the meaning of fearless challenge that failed. The beauty of tragedy was not produced on the destruction of life, but now this kind of value was in the impact activity. They performed for the reader about the tragedy on challenging for the limit and the death.