高品质轴承钢LF--VD过程非金属夹杂物演变规律

对国内一钢厂EAF→LF→VD→CC工艺生产的高品质GCr15轴承钢进行系统取样,针对DS类非金属夹杂物随机性强的特点,利用能够进行大面积试样检测的ASPEX自动扫描电镜分析统计钢中非金属夹杂物的成分、尺寸、数量等信息。研究发现：GCr15轴承钢冶炼过程中非金属夹杂物主要为MgO- Al2 O3- CaO复合夹杂物和MnS,同时有少量的SiO2- Al2 O3和MgO-Al2 O3复合夹杂物;夹杂物尺寸主要集中在3~8μm,并有少量DS类夹杂物出现且尺寸范围波动很大,最大可以达70μm以上,形貌为圆形或近似圆形;VD有较强的去除夹杂物功能,经过VD真空精炼,夹杂物中CaO含量有增加趋势;吊包至铸坯过程,夹杂物成分向Al2 O3含量增多的区域移动,最终轴承钢铸坯中夹杂物成分位于高Al2 O3含量(≥80%),少量MgO (<20%)和低CaO(<5%)的区域;DS夹杂物的生成和去除具有较强的随机性。     

精炼渣成分与轴承钢夹杂物类型关系热力学分析

针对轴承钢中钙铝酸盐大型夹杂物的控制问题,通过计算GCr15轴承钢中尖晶石MgO·Al2 O3、钙的铝酸盐CaO·6Al2 O3夹杂物生成热力学,分析精炼渣成分与夹杂物类型之间的定量关系.结果表明：当钢水中含有质量分数0.10×10-6的溶解钙[Ca]时,只要溶解镁[Mg]质量分数小于10×10-6,MgO·Al2O3就会被[Ca]还原成 CaO·6Al2O3;当精炼渣碱度为7.04,(MgO)质量分数为1.38%时,钢水中溶解[Mg]质量分数比临界[Mg]质量分数低56%,夹杂物以尺寸大于10μm的CaO-Al2O3系复合夹杂为主;当精炼渣碱度为3.75,(MgO)质量分数3.14%时,钢水中溶解[Mg]质量分数比临界[Mg]质量分数低14%,夹杂物以尺寸小于8μm的MnS包裹MgO·Al2 O3复合夹杂为主;当精炼渣钙铝比C/A为1.8~2.0时,控制精炼渣碱度R为4.5~5.5,(MgO)质量分数为3%~5%,即能使钢中MgO·Al2O3保持稳定而不转变为CaO·6Al2O3.     

气瓶钢精炼过程中的MgO·Al_2O_3夹杂物

研究了EAF-LF-VD-CC流程冶炼气瓶钢30CrMo时精炼过程中含MgO.Al2O3夹杂物的生成和转化,对夹杂物进行了三维分析观察.研究结果表明:LF精炼30min后夹杂物中Mg含量减小,Ca含量增加,MgO.Al2O3夹杂物消失.LF精炼后期Mg含量变化不大,Ca含量减小,未出现MgO.Al2O3夹杂物;VD精炼过程中夹杂物中的Mg含量增加,Ca含量变化不大,重新生成了MgO.Al2O3夹杂物;精炼过程中MgO.Al2O3夹杂物可以向复合夹杂物转变的,但为防止精炼后期MgO.Al2O3夹杂物重新生成必须保证钢液中具有一定的钙含量.     

高品质GCr15轴承钢二次精炼过程中夹杂物的演变规律

采用FE-SEM/EDS研究了转炉流程生产的GCr15轴承钢LF、RH精炼过程中夹杂物的演变规律,分析了其演变机理。结果表明:钢中复合夹杂物的演变规律可归纳为:Al2O3→MgO·Al2O3→(CaO-MgO-Al2O3-(CaS))复合氧化物夹杂和Al2O3→(Al2O3-MnS)→(Al2O3-MnS-Ti(C,N))复合氧硫碳氮物夹杂2种方式。LF精炼过程脱硫作用明显,钢中的硫化物夹杂数量大幅减少。LF精炼初期钢中主要是MnS、Al2O3、TiN的单相夹杂物。LF精炼结束后钢中的夹杂物演变为Al2O3为核心外包氧化物及MnS、TiN、Ti(C,N)、CaS的复合夹杂物。精炼渣中的CaO和耐火材料中的MgO经还原后与钢中溶解氧反应导致LF精炼结束时D类夹杂物增加。RH及软吹处理进一步强化了去除钢中的硫化物,但D类及其与A、T类复合的夹杂物含量增加。在LF阶段,夹杂物尺寸主要集中在1~3μm范围内,到RH阶段,夹杂物尺寸则主要集中分布在小于1μm的粒度范围。最大夹杂物尺寸由10.79μm降到5.68μm,单位面积夹杂个数由372个/mm2降到258个/mm2。RH及软吹处理有效地降低了钢中大于3μm的夹杂物。     

合金钢中镁铝尖晶石夹杂物生成与转化热力学

通过FactSage 6.0热力学软件计算,研究了合金钢中镁铝尖晶石(MgO.Al2O3)形成和向低熔点复合夹杂物转化的热力学条件,以及钙处理对钢液成分和夹杂物成分的影响.研究结果表明:钢中生成镁铝尖晶石夹杂物需要镁的含量较低;当钢液中溶解钙的质量分数为1×10-6时,镁铝尖晶石会转化变成液态的复合夹杂物;随着钙加入量的增加,液态复合夹杂物中Al2O3和MgO的含量继续降低,CaO的含量继续增加,SiO2的含量较低,基本保持不变;随着钙加入量的增加,钢液中的氧含量会降低,镁含量增加.     

铝、镁脱氧钢中夹杂物的动态演变规律

本研究制备了不同氧、硫含量的实验钢,采用SEM-EDX和CSLM探讨了钢中夹杂物类型及高温演变规律.结果表明,脱氧生成的MgO大多为球形,而MgO·Al2O3呈现不规则形状.单独铝脱氧钢中Al2O3夹杂物通过移动、碰撞、聚合的方式形成大型簇团.铝镁复合脱氧钢中夹杂物形貌和动态演变随着［Al］,［Mg］和［S］含量的变化呈现出不同的现象.当［Mg］,［Al］含量满足MgO生成条件时,夹杂物无明显聚合现象,呈弥散分布的特征;当［Mg］,［Al］含量位于MgO·Al2O3生成区域时,未观察到团簇状夹杂物出现,但夹杂物粒径较MgO大;当夹杂物成分同时满足MgO和MgS生成条件时,夹杂物聚合趋势明显,推测是硫化物的形成促进了夹杂物的聚合现象.     

帘线钢夹杂物成分控制的最小自由能变化模型

应用共存理论和规划理论,以夹杂物与钢水化学反应自由能变化值最小化为目标,建立了夹杂物成分与结晶器钢水成分之间关系的数学模型.经验证,在夹杂物为液态的情况下,模型计算结果与实测结果相符合.利用模型计算了[Ca]、[Al]含量对夹杂物成分的影响.结果表明,为将CaO-SiO2-Al2O3系夹杂物控制在塑性区,结晶器中钢水[Al]含量应根据[Ca]含量的变化而变化.当[Ca]的质量分数为5×10-6时,应控制钢水中[Al]的质量分数在12×10-6左右.     

高级别管线钢钙处理冶金效果研究

针对管线钢L360QS进行了钙处理实验研究,考查钢液中[Ca]、[S]对夹杂物变性的影响.结果表明,钢中的硫被脱到0.002%～0.003%(质量分数)范围内的较低水平,脱硫率最高达85.0%,与实验预期吻合.随着钢液中[S]增加,夹杂物中CaS+MnS的平均质量分数相应增加,但夹杂物中的CaS含量不一定增加.钙对夹杂物变性作用非常明显,[Ca]相对高的管线钢,其夹杂物绝大多数都变性为球形的含CaS钙铝酸盐复合夹杂,不存在MnS夹杂和MgO.Al2O3夹杂.为使氧化夹杂和硫化夹杂都变性完全,钢液中的硫的质量分数应控制在0.002%左右,钙的质量分数应控制在0.003 5%～0.004 0%,且[Ca]/[S]>1.9.     

低碱度顶渣控制帘线钢中CaO-SiO2-Al2O3-MgO类夹杂物成分的实验研究

在实验室中用高温管式炉对用工业纯铁配制的帘线钢进行脱氧和顶渣熔炼,研究了炉渣成分对夹杂物成分的影响.在炉渣碱度一定的情况下,随着炉渣中Al2O,含量的增加,夹杂物中的Al2O,含量也随之增加.当炉渣中的Al2O,含量低于8%时,夹杂物中的成分在塑性区.通过控制脱氧条件和顶渣成分可以把夹杂物的成分控制在塑性区内.     

GCr15轴承钢中TiN复合夹杂物形成机理

在GCr15轴承钢扫描电镜观察中发现有两类复合TiN夹杂物,分别为:TiN-MnS和TiN-MgO-MgAl_2O_4-MnS。热力学计算表明,GCr15轴承钢中TiN夹杂物在固液两相区析出,MnS在固相区析出,Mg元素部分来源于炉衬中MgO被钢液中溶解的碳侵蚀还原,[Mg]与[O]将已经形核的Al2O3改质为MgAl_2O_4。TiN-MgOMgAl_2O_4-MnS的析出顺序依次为:MgAl_2O_4、MgO、TiN、MnS。MgO可作为TiN的形核质点;MgAl_2O_4若作为MgO、TiN、MnS的形核质点,取决于其周围元素的类型以及析出温度。     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

On Tragic Consciousness In The Works By Ernest Hemingway

As an American modern novelist who were famous in the literary world, Hemingway was not a person who always followed the trend but a sharp observer. At the same time, he was a tragedy maestro, he paid great attention on existence, fate and end-result. The dramatis personae's tragedy of his works was an extreme limit by all means tragedy on the meaning of fearless challenge that failed. The beauty of tragedy was not produced on the destruction of life, but now this kind of value was in the impact activity. They performed for the reader about the tragedy on challenging for the limit and the death.     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with