含非晶和纳米晶Al-Ni-Y块体合金的制备

采用紧耦合惰性气体雾化技术制备Al82Ni10Y8非晶和纳米晶粉末,并利用超高压固结成形技术对雾化粉末进行致密化.利用差示扫描量热分析(DSC)、X射线衍射(XRD)、扫描电镜(SEM)和透射电镜(TEM)等对合金的热稳定性、物相组成、微观组织和形貌进行分析,研究合金的致密化机理.研究结果表明:所制备的块体材料保持了原始粉末状态的非晶及纳米晶结构;非晶相的粘滞流动和在三向应力作用下氧化膜的破裂促进颗粒结合是低温下材料获得较高致密度的主要原因.     

超音速气雾化制备316 L不锈钢粉末的表征

利用自行研制的超音速雾化技术制备了316 L不锈钢粉末,采用激光粒度仪、扫描电镜、金相显微镜和X射线衍射仪进行了表征. 结果表明,316 L不锈钢粉末的平均粒度约为24 μm,粒度分布的几何标准偏差δ为1.75;粉末内部存在三种典型凝固组织,即具有发达二次枝晶的枝晶组织、胞晶组织以及枝状晶与胞状晶的混合组织;大粒径气雾化316 L不锈钢粉末为单一的γ奥氏体相,小粒径粉末由γ奥氏体相+少量δ铁素体相共同组成;熔滴的冷速随着粒径的减小而提高,平均冷却速率为104～107 K·s-1.     

氩气雾化René104镍基高温合金粉末的显微组织和凝固缺陷

采用氩气雾化制备René104(ME3)镍基高温合金粉末,对粉末的粒径分布、形貌、显微组织和凝固缺陷进行分析。研究结果表明:氩气雾化René104高温合金粉末氧含量较低,以球形和近球形为主;细粉收得率高,粒径小于75μm的粉末达到70%。小于60μm的粉末成分均匀,表面光滑,内部结构致密,具有典型的胞状晶组织。随着粒径的增大,粉末表面和内部开始出现树枝晶组织,显微组织为胞状晶+树枝晶;具有胞状晶+树枝晶组织的粉末开始出现内部凝固缩孔和空心现象,粒径大于75μm粉末明显观察到内部凝固缩孔和空心缺陷。     

紧耦合气雾化制备Al基非晶合金粉末

开展了采用紧耦合气雾化方法制备Al基合金粉末的实验和理论研究.利用X射线衍射仪、差热分析仪、扫描电镜和透射电镜分析了粉末的表面形貌、显微组织和结构特征,根据气雾化过程中熔滴的破碎模式和冷却行为确定了Al基合金的非晶化临界冷却速率及相应粉末粒径.结果表明:气雾化粉末中存在部分非晶粉末,非晶粉末的粒径小于26μm;Al基合金的非晶化临界冷却速率大致为106K.s-1;雾化中熔体的破碎和冷却是两个相互耦合(矛盾)的过程,快速冷却(大于104K.s-1)极大地阻碍熔体的充分雾化,同时熔滴的破碎模式对其冷却行为具有显著的影响.目前紧耦合气雾化技术还只能制得非晶/晶态混合的Al基合金粉末.     

Zr_(55)Al_(10)Ni_5Cu_(30)大块金属玻璃的晶化行为研究

分别在603 K、653 K、683 K、723 K、753 K、793 K和0.5 h、1 h、2 h、3 h、5 h的保温时间下对Zr55Al10Ni5Cu30大块金属玻璃进行了退火热处理.采用x射线衍射(XRD)法分析了退火后Zr55Al10Ni5Cu30大块金属玻璃的弛豫和晶化相析出的过程,计算了不同温度下结晶度和纳米晶粒尺寸的大小.通过差示扫描量热(DSC)法分析了Zr55Al10Ni5Cu30大块金属玻璃的热稳定性.Kjssinger曲线分析表明,Zr55Al10Ni5Cu30大块金属玻璃弛豫后晶化激活能高于其淬态的晶化激活能,退火温度对大块金属玻璃热稳定性有显著影响.     

喷射成形制备La62Al15.7(Cu,Ni)22.3块体非晶合金

采用喷射沉积成形方法制备了La62Al15.7(Cu,Ni)22.3块体非晶合金. 结果表明,沉积态La62Al15.7(Cu,Ni)22.3非晶合金比以往报道的采用甩带法制备的同成分非晶合金具有更大的约化玻璃转变温度和更宽的过冷液相区. 非晶的晶化实验表明,晶化初期多种晶相同时结晶析出. 483K退火时,在非晶基体中析出Al和AlNi. 503K退火时进一步析出La和未知相. La62Al15.7(Cu,Ni)22.3非晶合金在573K退火没有新相产生,合金晶化态组织由Al、AlNi、La和未知相组成.     

机械合金化法制备Cu-Ti-Zr基非晶合金

采用机械合金化法成功制备Cu40Ti60-xZr(x=0,10,30,50)非晶合金.研究Cu-Ti-Zr合金粉末由晶态向非晶态转变过程中的组织结构变化,探讨非晶合金的形成机制,以及非晶合金的热稳定性和晶化产物.结果表明,非晶合金直接从初始元素得到,在反应过程中没有金属间化合物出现,非晶化过程可以由间隙扩散模型来解释.Cu40TixZry非晶粉末的DSC分析表明,随着Ti含量的降低和Zr含量的升高,非晶粉末的晶化温度Tx逐渐升高,对非晶粉末在相应的Tx温度附近退火15min后发现,Cu40Ti30Zr30合金没有析出相,Cu40Ti1Zr50析出了Zr2Cu,Cu4Ti和少量的一些未知相.     

机械合金化La8 Mg52 Ni40合金的相组成研究

采用机械合金化及热处理等方法制备了La8Mg52Ni40新型合金,并用X-射线衍射(XRD)、扫描电子显微镜(SEM)、差热分析(DTA)等方法研究了其组织结构及热稳定性能等.研究结果表明:La8Mg52Ni40合金经280 r/min球磨250 h后,获得了镧、镁、镍等非晶相和MgNi2纳米晶结构;所得粉末的形状为规则的球形或近球形,颗粒直径范围约为0.05～12.5 μm,其中,粒径为0.5～2 μm的颗粒数约占颗粒总数的97%.球磨样品经763 K保温35 d热处理后,得到了具有纳米尺度的Mg2NiLa,Mg2Ni,MgNi2三相合金,样品具有较好的热稳定性能.图4,表2,参12.     

Zr对Al-Ni-Y-(Zr,Cu)合金系非晶形成能力及热稳定性的影响

通过Zr部分取代Al80Ni10YsCu5中的Y,获得了Al80Ni10Y5-xZrxCus（x=0、1、2、3、4）铝基非晶合金．用XRD和DSC等测试手段1分析了单辊旋淬法制备的该合金非晶条带,研究了Zr对合金体系非晶形成能力和热稳定性的影响．结果表明,x=2或x=3的合金的衍射峰较为宽化;当x从0增加到2时,合金的晶化温度增加,此后,随x的进一步增加,合金的晶化温度先降低后又有所回升．Al80Ni10Y3Zr2Cu5合金既具有相对较好的非晶形成能力,又具有较高的热稳定性．     

冷喷涂NiCoCrAlY涂层的组织结构特征与抗氧化性能研究

利用低压冷喷涂技术制备了Ni Co Cr Al Y涂层,采用SEM、XRD分析了涂层的组织结构特征,利用静态氧化实验研究了抗氧化性能。结果表明,冷喷涂Ni Co Cr Al Y涂层含氧量为0.25%,涂层孔隙率小于0.92%;冷喷涂过程中,喷涂粉末材料发生了相变,由γ-Matrix Ni-Co-Cr固溶体和β-(Ni,Co)Al金属间化合物双相结构转变为γ-Matrix单相结构,同时涂层中含大量纳米晶;经1 050℃氧化400 h后,冷喷涂Ni Co Cr Al Y涂层表面除α-Al2O3外还生成了少量尖晶石,氧化膜未见明显脱落,厚度为2.85±0.12μm,预计还有较长的抗氧化寿命。     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Lower Paleozoic oil relationships within Williston Basin, Canada

The Williston Basin is a significant petroleum province, containing oil production zones that include the Middle Cambrian to Lower Ordovician, Upper Ordovician, Middle Devonian, Upper Devonian and Mississippian and within the Jurassic and Cretaceous. The oils of the Williston Basin exhibit a wide range of geochemical characteristics defined as "oil families", although the geochemical signature of the Cambrian Deadwood Formation and Lower Ordovician Winnipeg reservoired oils does not match any "oil family". Despite their close stratigraphic proximity, it is evident that the oils of the Lower Palaeozoic within the Williston Basin are distinct. This suggests the presence of a new "oil family" within the Williston Basin. Diagnostic geochemical signatures occur in the gasoline range chromatograms, within saturate fraction gas chromatograms and biomarker fingerprints. However, some of the established criteria and cross-plots that are currently used to segregate oils into distinct genetic families within the basin do not always meet with success, particularly when applied to the Lower Palaeozoic oils of the Deadwood and Winnipeg Formation.     

An Analysis of Catherine＇s Character——Wuthering Heights

Wuthering Heights, Emily Bronte＇s only novel, was published in December of 1847 under the pseudonym Ellis Bell. The book did not gain immediate success, but it is now thought one of the finest novels in the English language. Catherine is the key character of this masterpiece, because everybody and everything center on her though she had a short life. We can understand this masterpiece better if we know Catherine well.     

Features of Women's language

Language is a means of verbal communication. People use language to communicate with each other. In the society, no two speakers are exactly alike in the way of speaking. Some differences are due to age, gender, statue and personality. Above all, gender is one of the obvious reasons. The writer of this paper tries to describe the features of women＇s language from these perspectives： pronunciation, intonation, diction, subjects, grammar and discourse. From the discussion of the features of women＇s language, more attention should be paid to language use in social context. What＇s more, the linguistic phenomena in a speaking community can be understood more thoroughly.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

Design and analysis of generic LBS application developing platform

Location based services is promising due to its novel working style and contents.A software platform is proposed to provide application programs of typical location based services and support new applications developing efficiently. The analysis shows that this scheme is easy implemented, low cost and adapt to all kinds of mobile nework system.     

橡胶颗粒沥青混合料低温抗裂性试验研究

以AC-13级配为基础,将橡胶颗粒代替部分集料掺入混合料中,以低温弯曲试验为评价方法对不同橡胶颗粒掺量下沥青混合料的低温抗裂性进行研究,并引入应变能密度值对混合料的低温抗裂性进行综合评价.试验结果表明:橡胶颗粒沥青混合料试件的破坏微应变均超过2 300,满足冬寒区的技术指标;无论是否掺加橡胶颗粒,随着温度的下降,沥青混合料破坏时的最大弯拉强度增大,弯拉应变降低,劲度模量增大;弯曲应变能密度在胶粒掺量为1%左右时具有较大的弯曲应变能密度值,此时橡胶颗粒沥青混合料具有较好的低温抗裂性.     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

Quantitative trait loci （QTLs） for quality traits related to protein and starch in wheat

Quality traits in wheat （Triticum aestirum L.） were studied by quantitative trait locus （QTL） analysis in a recombinant inbred line （RIL） population, a set of 131 lines derived from Chuan 35050 × Shannong 483 cross （ChSh）. Grains from RILs were assayed for 21 quality traits related to protein and starch. A total of 35 putative QTLs for 19 traits with a single QTL explaining 7.99-40.52% of phenotypic variations were detected on 10 chromosomes, 1D, 2A, 2D, 3B, 3D, 5A, 6A, 6B, 6D, and 7B. The additive effects of 30 QTLs were positive, contributed by Chuan 35050, the remaining 5 QTLs were negative with the additive effect contributed by Shannong 483. For protein traits, 15 QTLs were obtained and most of them were located on chromosomes 1 D, 3B and 6D, while 20 QTLs for starch traits were detected and most of them were located on chromosomes 3D, 6B and 7B. Only 7 QTLs for protein and starch traits were co-located in three regions on chromosomes 1D, 2A and 2D. These protein and starch trait QTLs showed a distinct distribution pattern in certain regions and chromosomes. Twenty-two QTLs were clustered in 6 regions of 5 chromosomes. Two QTL clusters for protein traits were located on chromosomes 1D and 3B, respectively, three clusters for starch traits on chromosomes 3D, 6B and 7B, and one cluster including protein and starch traits on chromosome 1D.     

On Tragic Consciousness In The Works By Ernest Hemingway

As an American modern novelist who were famous in the literary world, Hemingway was not a person who always followed the trend but a sharp observer. At the same time, he was a tragedy maestro, he paid great attention on existence, fate and end-result. The dramatis personae's tragedy of his works was an extreme limit by all means tragedy on the meaning of fearless challenge that failed. The beauty of tragedy was not produced on the destruction of life, but now this kind of value was in the impact activity. They performed for the reader about the tragedy on challenging for the limit and the death.