| 自蔓延焊条的焊接工艺性研究 |
| |
| 引用本文： | 门自兵,张国栋,李旭东,张新佳. 自蔓延焊条的焊接工艺性研究[J]. 云南师范大学学报(自然科学版), 2014, 0(1): 71-74 |
| |
| 作者姓名： | 门自兵 张国栋 李旭东 张新佳 |
| |
| 作者单位： | [1]中国电力投资集团公司宁夏青铜峡能源铝业集团有限公司,宁夏银川750000 [2]武汉大学动力与机械学院,湖北武汉430072 |
| |
| 基金项目： | 国家大学生创新实验资助项目（081048626）;湖北省自然科学基金资助项目（2009CDB300）;中央高校基本科研业务费专项资金资助项目（5082001）. |
| |
| 摘 要： | 研究了焊药密实度、焊前预热、焊接速度、试板厚度和后热等对自蔓延焊条的焊接工艺性影响规律.结果发现,当药粉密度在2.60~2.80g/cm3时,自蔓延焊条燃烧速度为10.5mm/s,焊接可控性好.焊前350℃预热可以增加焊接熔深,实现单面焊双面成形效果.焊接速度取决于试板厚度,提高焊接速度明显降低较厚试板的焊透性和焊接效果.后热对自蔓延焊条工艺性能没有显著影响.
|
| 关 键 词： | 自蔓延焊条 焊接工艺 密实度 预热 焊接速度 |
Welding Process of Manual SHS Welding Electrode |
| |
| MEN Zi-bing;ZHANG Guo-dong;LI Xu-dong;ZHANG Xin-jia. Welding Process of Manual SHS Welding Electrode[J]. Journal of Yunnan Normal University (Natural Sciences Edition), 2014, 0(1): 71-74 |
| |
| Authors: | MEN Zi-bing ZHANG Guo-dong LI Xu-dong ZHANG Xin-jia |
| |
| Affiliation: | MEN Zi-bing;ZHANG Guo-dong;LI Xu-dong;ZHANG Xin-jia(Ningxia Qingtongxia Energy Aluminum Group Co., Ltd., China Power Investment Corporation, Yinchuan 750002,China;College of Power and Mechanical Engineering, Wuhan University, Wuhan 430072, China) |
| |
| Abstract: | The influence of flux density,preheating,welding speed,plate thickness and post welding heat on welding process of SHS welding electrode were studied.The results showed that the good welding controllability was obtained when the powder density was 2.60～2.80 g/cm3,and the burning speed is 10.5 mm/s.The welding penetration was improved and the one side welding was achieved via welding preheating at 350 ℃.The welding speed depended on the plate thickness,and the increase of welding speed obviously decreased the welding penetration and welding result of the thicker plate.It could also be found that the post heat had no significant effect on the welding process properties. |
| |
| Keywords: | SHS welding electrode Welding process Density Preheating Welding speed |
| 本文献已被 CNKI 维普 等数据库收录！ |
|
