| 预应力混凝土T梁桥端部锚固区拉压杆模型及配筋设计 |
| |
| 引用本文： | 林波,刘钊,郑和晖,王景全.预应力混凝土T梁桥端部锚固区拉压杆模型及配筋设计[J].东南大学学报(自然科学版),2009(Z2). |
| |
| 作者姓名： | 林波 刘钊 郑和晖 王景全 |
| |
| 作者单位： | 东南大学混凝土及预应力混凝土结构教育部重点实验室; |
| |
| 基金项目： | 国家自然科学基金资助项目(50778038); 教育部博士点基金资助项目(20070286097) |
| |
| 摘 要： | 根据有限元应力分析结果,抽象出力流传递路径,提出了T梁端部锚固区拉压杆模型的构形方法.通过对劈裂应力的数值积分,计算合力作用点位置,并将其作为拉杆位置确定的依据.分析表明,由于T梁端部锚固力的合力对截面形心的偏心距不大,劈裂应力合力作用点至锚固端的距离与梁高的比值,基本不受锚下预加力大小、梁高以及翼板宽度变化的影响,大小稳定在0.67~0.69之内.最后,应用该构形方法,得到了跨度为20~50m的T梁端部锚固区拉压杆模型,将由拉压杆模型计算出的劈裂力大小与精细化有限元分析结果进行了比较,其比值分布在1.16~1.34范围之内,由此可见,由拉压杆模型给出的劈裂力计算值与有限元分析结果之间相差不大,且偏于安全.
|
| 关 键 词： | 拉压杆模型 劈裂力 端部锚固区 配筋设计 有限元分析 |
Strut-and-tie models for end anchorage zones in prestressed concrete T-section girder bridges and reinforcement design |
| |
| Lin Bo Liu Zhao Zheng Hehui Wang Jingquan.Strut-and-tie models for end anchorage zones in prestressed concrete T-section girder bridges and reinforcement design[J].Journal of Southeast University(Natural Science Edition),2009(Z2). |
| |
| Authors: | Lin Bo Liu Zhao Zheng Hehui Wang Jingquan |
| |
| Institution: | Lin Bo Liu Zhao Zheng Hehui Wang Jingquan (Key Laboratory of Concrete , Prestressed Concrete Structures of Ministry of Education,Southeast University,Nanjing 210096,China) |
| |
| Abstract: | According to the results of the finite element analysis,load paths were drawn and strut-and-tie models(STMs) for end anchorage zones in T-section girder bridges were proposed.Through integrating the bursting stresses along the tendon axis,the location of the resultant bursting force was obtained,which was taken as a basis to determine the location of ties.The results show that because the eccentricity of the resultant anchoring force from the center of the girder section is not great,the ratio of the space ... |
| |
| Keywords: | strut-and-tie model bursting force end anchorage zone reinforcement design finite element analysis |
| 本文献已被 CNKI 等数据库收录！ |
|
