基于多材质复合管柱的裸眼井壁支撑工艺及应用

已完钻超深裸眼水平井侧钻技术是经济、高效开发油藏剩余油的主要手段之一，传统的磨铣钢套管开窗侧钻技术存在下入摩阻大、磨铣耗时长导致开窗失败等问题。为此，提出了基于多材质复合管柱的超深水平井裸眼井壁支撑工艺，结合中国西北油田已完钻超深裸眼水平井井况，首先，提出了基于“铝合金+碳钢”的多材质复合管柱组合及设计方法；其次，开展了基于管柱实物屈曲实验数据的管柱临界屈曲载荷计算模型适用性评价，并优选出了适合于“铝合金+碳钢”多材质复合管柱的屈曲临界载荷计算模型；最后，研究了综合考虑管柱扭矩、摩阻、刚性、井眼条件、管柱强度及材质的多材质复合管柱下入性分析方法，并利用下入性分析软件对西北油田顺北X1井、X2井、X3井、X4井复合管柱进行了下入可行性评价。该方法在X1井和X2井得到成功应用，进一步论证了该工艺现场应用的可行性。研究成果可为超深水平井裸眼井壁支撑的复合管柱设计和下入可行性评价提供理论参考。     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

激光快速成型TC4合金显微组织及力学性能

采用金相显微镜、扫描电镜、电子拉伸机等，研究了激光快速成型TC4合金沉积态在平行沉积方向和垂直沉积方向的组织和力学性能.结果表明:激光快速成型TC4合金沉积态宏观组织沿沉积方向生长的粗大β柱状晶呈明暗相间的条带状结构，具备典型的魏氏组织特征;垂直沉积方向的强度比平行沉积方向的强度高，但塑性低;合金断口为韧窝状断口，垂直沉积方向的断口韧窝尺寸比平行沉积方向的小.     

定逆序数的n元数码置换个数的一种方法

一个确定的n元数码的排列,其道序数是不难求得的;反之,“已知逆序数,求有多少个n元置换”的问题要复杂得多。从最小数码的位置着手,充分利用逆序数是定数,给出一种解决此问题的新方法——最小数码定位法。此法通俗易懂,由此得到了逆序数为k(k=1,2,3……c_n~2)的n元数码的置换个数的一个递推公式:q_k(n)=1+q_1(n-l)+q_2(n-1)+q_3(n-1)+…+q_k(n-1)。     

运用试验设计法优化某军品压铸弹尾工艺

根据某军品部件出现的问题，应用试验设计法成功地找出了最优组合，提高了该部件的强度，解决了该强度问题，使生产得以正常进行。     

雷电波分析与比较研究

本文对双指数雷电流模型和 IEC1 3 1 2—— 1推荐的雷电流模型进行了分析和研究 ,计算了这两种雷电流模型的雷电流参数。在此基础上 ,用 FFT方法分析了雷电流的频谱分布     

具有sn-网的空间

证明了具有σ—点有限sn—网及σ—局部可数sn—网的空间可刻划为度量空间在某些确定映射下的象.     

Supercritical Fluid Carbon Dioxide in the Extraction of Lanolin and Its Alcohol

The use of supercritical fluid carbon dioxide (SF-CO_2) in extraction of lanolin and its alcohol issuperior to the conventional solvent extractionmethod. Its distinctive advantages include highextractive ratio, nontoxic and nonflammablesolvents, and minimal by-product pollution. The     

实时系统开发与PEARL语言

本文讨论了实时系统的特征、开发方法、设计工具、实现手段工具等开发过程中的主要问题,论述了实时系统开发语言PEARL及该语言的对实时系统的主要支持.