Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

基于突变级数法的福州市某区土壤重金属污染综合评价

以福州市某区土壤为研究对象,采用突变级数法对福州市某区土壤重金属污染进行评价,依据主成分分析对评价因子进行选择,整个评价指标体系避免了人为确定权重的主观性.结果表明:福州市某区土壤重金属污染目前整体呈现一个较为良好的态势,但有部分地区处于"病态"状况.距离该区中心较近的西客站、李园天桥、远洋以及于山、东街口到靠近郊区的燎原、三角埕、鼓山等地的污染的综合隶属值呈递增的趋势,表明距离城市中心越近的土壤重金属污染越为严重.     

非同分布φ混合序列加权和的强极限收敛性

利用φ混合序列矩不等式和截尾的处理方法,研究非同分布φ混合序列加权和强极限收敛性质的问题,得到了若干新结果,推广并改进了独立同分布情形下的相应结果.     

循环作用对马蹄寺石窟群岩体性能的影响

马蹄寺石窟群地处河西走廊中部,气候条件十分恶劣。由于常年受到温度、湿度、酸碱盐等作用的影响,石窟岩体性能出现了不同程度的劣化现象。通过开展室内模拟试验,研究以上多种恶劣环境的循环作用对于岩体抗压强度、波速、质量的影响规律,同时使用X射线衍射仪(X-ray diffraction,XRD)、X射线荧光光谱(X-ray fluorescence,XRF)和扫描电子显微镜(scanning electron microscope,SEM)对循环作用过程中样品的矿物组分、元素含量和微观形貌进行分析研究。研究结果表明,循环作用使样品中的长石类矿物和方解石含量降低,黏土类矿物含量增加,胶结程度下降,孔隙逐渐发展成为横向微裂隙,导致样品的性能出现不同程度的劣化现象。循环作用对岩体性能的影响程度从大到小依次为冻融循环、耐盐循环、耐碱循环、耐酸循环和温湿循环。     

高温作用后砂岩物理力学性质阈值温度的确定——基于机器学习算法

通过采用机器学习算法，提出了高温作用后砂岩物理力学性质变化的阈值温度的确定方法。基于Python语言，利用K-Means、SVM算法，实现了对样本数据的分类和聚类，确定了阈值温度区间，验证了二分类法的合理性和准确性.结果表明，砂岩样本的阈值温度区间为400~600 ℃，阈值温度上下砂岩的物理力学性质存在显著差异，体现为阈值温度区间以下的岩样物理力学性质较为分散，而阈值温度区间以上的岩样物理力学性质较为集中.     

喷射共沉积6066Al/SiCp复合材料热处理塑性变化机理分析

研究了T6热处理对6066Al/SiCp复合材料材料力学性能的影响,结果表明,复合材料经530℃固溶1 h后,170℃时效8 h达到峰时效,其抗拉强度达418.6 MPa;复合材料延伸率随时效时间的增加不断降低.     

不饱和烃同系物凝聚型物理性质递变规律的数学描述

以H-(CH2)n-CH=CH2和H-(CH2)n-C≡CH型同系物结构重复单元数值连续变化为模型,获得了描述该同系物凝聚型物理性质递变规律的数学表达式:P=(a0+a1n+a2n2)/(1+b2n2),式中a0、a1、a2、b2均为常数,n为结构重复单元数值,P为同系物的凝聚型物理性质。通过非线性回归分析,得到回归方程,结果表明同系物的凝聚型物理性质与重复结构单元数值之间满足上述关系式,并显示优良的相关性。     

望江矶雨花台砾石层工程地质特性及形成机理

根据野外考察与实验资料，对南京雨花区望江矶的雨花台砾石层的工程地质性质作出初步评价认为该砾石层具有一定的固结性，较好的水稳性，较强的抗剪性，中低压缩性不同于现代松散的砂砾石堆积体，作者还运用沉积原理及风化理论对影响其工程地质性质的作用因素进行了探讨。     

钛酸铋的热力学理论

利用点群４／ｍｍｍ的对称性给出了应力作用下的钛酸铋的弹性吉布斯自由能的表达式，并导出了自发应变，介电性质和压电性质。