基于多材质复合管柱的裸眼井壁支撑工艺及应用

已完钻超深裸眼水平井侧钻技术是经济、高效开发油藏剩余油的主要手段之一，传统的磨铣钢套管开窗侧钻技术存在下入摩阻大、磨铣耗时长导致开窗失败等问题。为此，提出了基于多材质复合管柱的超深水平井裸眼井壁支撑工艺，结合中国西北油田已完钻超深裸眼水平井井况，首先，提出了基于“铝合金+碳钢”的多材质复合管柱组合及设计方法；其次，开展了基于管柱实物屈曲实验数据的管柱临界屈曲载荷计算模型适用性评价，并优选出了适合于“铝合金+碳钢”多材质复合管柱的屈曲临界载荷计算模型；最后，研究了综合考虑管柱扭矩、摩阻、刚性、井眼条件、管柱强度及材质的多材质复合管柱下入性分析方法，并利用下入性分析软件对西北油田顺北X1井、X2井、X3井、X4井复合管柱进行了下入可行性评价。该方法在X1井和X2井得到成功应用，进一步论证了该工艺现场应用的可行性。研究成果可为超深水平井裸眼井壁支撑的复合管柱设计和下入可行性评价提供理论参考。     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

激光快速成型TC4合金显微组织及力学性能

采用金相显微镜、扫描电镜、电子拉伸机等，研究了激光快速成型TC4合金沉积态在平行沉积方向和垂直沉积方向的组织和力学性能.结果表明:激光快速成型TC4合金沉积态宏观组织沿沉积方向生长的粗大β柱状晶呈明暗相间的条带状结构，具备典型的魏氏组织特征;垂直沉积方向的强度比平行沉积方向的强度高，但塑性低;合金断口为韧窝状断口，垂直沉积方向的断口韧窝尺寸比平行沉积方向的小.     

水溶性La_(0.88)Sr_(0.12)MnO_3纳米粒子的非水相合成

采用纳米微乳液法,以三嵌段共聚物聚氧乙烯-聚氧丙烯-聚氧乙烯(PEO-PPO-PEO)为表面活性剂,乙酰丙酮镧(III),乙酰丙酮锰(III)和乙酰丙酮锶(II)为前驱体,1,2-十六烷二醇为还原剂成功合成了水溶性La0.88Sr0.12MnO3纳米粒子.FT-IR分析证实该纳米粒子表面存在PEO-PPO-PEO分子,XRD和TEM分析表明该纳米粒子基本上呈球形、粒径分布窄、结晶度高,VSM测试表明该纳米粒子室温下显示软铁磁性.纳米粒子在水中快速和高效的分散收集过程,表明该纳米粒子具有良好的水溶性和磁操控性.     

运用试验设计法优化某军品压铸弹尾工艺

根据某军品部件出现的问题，应用试验设计法成功地找出了最优组合，提高了该部件的强度，解决了该强度问题，使生产得以正常进行。     

交变磁场对磁性磨粒的作用分析

对处于交变磁场作用下的磁性磨料颗粒的受力和运动规律进行了分析和描述，为交变磁场作用下的磁粒研磨光整加工技术提供了新的思路和工艺选择。     

PLC在磁场压力机中的应用

提出一种采用PLC控制的压制钕铁硼(Nd-Fe-B)磁性材料的机电一体系统，并介绍了系统重要组成部分：压机主体和电控箱，给出了电控箱中各控制部分的电路及工作原理。实验证明本系统具有结构紧凑、操作方便、控制性能好等优点。     

铅锡合金沉积物的显微组织

将离子浓度比为5∶5的铅锡电沉积分形生长沉积物制备成金相样品，用金相显微镜观察了它们的显微组织。结果表明，在此情况下，铅锡电沉积生成物由两相组成，即铅锡共晶相和铅基固溶相，两相呈交替层状分布。     

磁存储的研究现状及发展方向

磁性存储是最常用的大容量存储技术。其记录密度越来越高，发展也越来越快。通过对信息记录、读出和存储3个过程的分析，对硬磁盘记录、垂直磁记录和磁光记录的优缺点作了对比。指出了采用垂直记录模式、非晶结构合金薄膜或铁氧体薄膜介质是实现超高密度记录的方向，光辅助磁记录是很有希望的记录技术。还指出量子磁盘技术是未来极高密度记录的方向。