Long term monitoring of urban subsidence by Permanent Scatterer DInSAR

When using differential SAR interferometry (DInSAR) to monitor the surface deformation over a long time scale, it is often strongly affected by the spatial and temporal decorrelations and atmospheric dishomogeneities. The recently developed Permanent Scatterers (PS) technique proposed by Fertti et al. can overcome these difficulties by interpreting time-series of interferometric phase only at coherent point scatterers. In this study, we apply this PS technique using 25 ERS-1/2 scenes from 1992 to 2000 to monitor the subsidence in Suzhou. By using the linear deformation model, the deformation map in Suzhou urban area over the eight years is obtained. And the calculated results are in good agreement with the measurements of leveling.     

钢管单芯棒圆周剪切法的实验研究

介绍钢管圆周剪切的另一种方法－单芯棒圆周剪切法。通过运动学分析阐述了剪切金属的变形原理；实验研究证明了该方法的可行性并对切口断面质量进行了分析。     

WHOLLY-AROMATIC COPOLYESTERS CONTAINING IPA, 2.6-NDA, TPA, CLHQA AND PABA MONOMERS

The crystallinities, thermal properties, liquid crystal properties and rheologic properties oftwo series of the aromatic copolyesters are studied. One of them is composed of IPA, 2,6-NDA,CLHQA, PABA and. the other composed of TPA, 2.6-NDA, CLHQA, IPA. The results showthat the crystallinities of the aromatic copolyesters are relatively low and the melting point of thecopolyesters decreases with an increase of the unsymmetrical contents. These two series of aro-matic copolyesters are both suitable for the conventional melt spinning process and have a goodfiber forming property and a good thermal stability. The viscosities of aromatic copolyestermelts are greatly affected by the shear rate, hence the so-called" thinning under shearing" phe-nomenon. The melts have a rather high viscosity flow activation energy and a relatively lowelasticity.     

Thermal Deformation Measurement and Stress Analysis of PQFP Assembly during Power Cycling

ＴｈｅｒｍａｌＤｅｆｏｒｍａｔｉｏｎＭｅａｓｕｒｅｍｅｎｔａｎｄＳｔｒｅｓｓＡｎａｌｙｓｉｓｏｆＰＱＦＰＡｓｅｍｂｌｙｄｕｒｉｎｇＰｏｗｅｒＣｙｃｌｉｎｇＤａｉＦｕｌｏｎｇ（戴福隆）,ＳｈｉＬｉｎｇ（石玲）,ＷｅｎＸｉｕｍｅｉ（温秀梅）Ｄｅｐａｒｔｍ...     

热膨胀系数测定新方法

提出了一种测量材料热膨胀系数的新方法。此方法以云纹干涉原理及微机技术为基础,使用液体恒温,在常温状态下即可高精度地测限材料的热膨胀系数ａ值。     

粘胶基碳布电化学氧化表面处理的研究

本文用电化学氧化方法对粘胶基碳布进行表面处理。采用电位滴定法分析测定了氧化处理前后碳纤维表面酸性官能团含量的变化,用水滴铺展方法分析了处理前后碳布润湿性能的变化情况,探讨了酸性官能团含量、织物强力与复合材料层间剪切强度的关系,找出了以Ｈ３ＰＯ４为电解质的最佳电化学氧化表面处理工艺。     

三维云纹干涉法在PMMA材料特性分析中的应用

对云纹干涉法的原理、方法及实验系统进行了简要介绍,并利用三维云纹干涉仪实时测量了有机玻璃(PMMA)在三点弯曲时的三维位移场。对变形三维云纹图进行了分析,得出了三维应变分布图。     

A2017半固态合金二次加热组织演化

对SCR技术制备的A2017半固态坯料进行二次加热,利用光学显微镜,电镜,图像分析仪等手段,对坯料二次加热微观组织的演化进行了研究·实验结果表明,在相同加热温度条件下,随着保温时间的延长,晶粒平均等积圆直径增大,晶粒越来越圆整,液相率增加;提高二次加热温度,晶粒长大和球化速度加快·二次加热最佳工艺条件为加热温度580℃,保温时间40～60min或者加热温度600℃,保温20～40min,晶粒平均等积圆直径为70～90μm,固相率在70%左右,适合于半固态加工·组织演化机制分析表明,加热初期阶段,液相少,晶粒主要通过碰撞熔合快速长大;随着保温时间延长,液相增加,晶粒主要通过原子扩散慢速长大并发生...     

曲梁的剪应力和径向应力的积分方程解

给出了计算曲梁剪应力和径向应力的一种新方法，即直接对剪应力积分方程进行求解。所得剪应力和径向应力解析公式不仅满足平衡方程，且满足曲梁上、下表面处力的边界条件。算例表明，与其它采用了附加假设的近似解相比，这种新方法的解具有很高的精度，同弹性理论解非常接近。