螺栓连接大变形梁非线性振动特性的实验研究

柔性机械臂、大型可展开天线等机械结构的动作精度受运动过程中大变形几何非线性和连接处接触非线性的影响十分显著。以含螺栓连接结构的大变形梁作为研究对象，针对动力学建模和振动特性开展了实验研究，通过数值计算验证了实验发现的非线性振动特性。搭建了含螺栓连接柔性大变形梁的实验台架，开展了敲击和正弦激振的实验测试。实验结果表明，螺栓连接的柔性梁较连续梁的（无螺栓连接）模态频率降低，阻尼增加，反映出随着激励能量增大，模态频率降低的非线性模态特征。改变螺栓连接位置会显著影响结构的模态频率，其变化规律可由求解线性矩阵特征值定性反映。     

轧制道次间插入冷却对特厚钢板组织与性能的影响

使用实验轧机旁冷却装置配合轧机进行轧制实验，研究轧制道次间不同冷却工艺对特厚钢板组织和性能的影响规律.研究结果表明:采用道次间冷却工艺可以在全厚度方向获得组织细化及强韧性提高效果，采用强冷道次间冷却实验钢1/4处晶粒尺寸可细化至10μm，强度为376MPa，-40℃冲击功为169J;心部晶粒尺寸可细化至15μm，强度为360MPa，-40℃冲击功为123J.本工艺可形成470μm厚表层细晶层，晶粒尺寸可细化至5μm;粗轧道次间插入冷却工艺轧制钢板强度和冲击韧性优于中间坯冷却工艺;随冷却强度增加，钢板内部组织明显细化且强度大幅提高.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

基于Sinc插值与相关谱的纵横波速度比扫描方法

在多分量地震技术中，准确地求取出纵、横波速比（γ）是多分量资料处理、反演、解释各环节中的一个重要步骤。由于地下同一层位具有相同的波阻抗比，因此该层位的反射纵波和反射转换波相互关联，纵横波速比与时间比存在相互转化关系。基于Sinc插值算法与相关系数谱分析的纵横波速比扫描方法是通过设置一系列γ，利用Sinc插值算法将纵波拉伸后与转换波进行互相关，当互相关系数达到最大时即可求出相应的γ。理论数据和实际资料的测试，验证了该方法的有效性、准确性和实用性。     

音序、形序、义序:并存还是取代?——也谈词典词目编排法

按词目的编排方法分,词典可分为三大类:音序词典、形序词典和义序词典。这三类词典各有优点和缺点;它们之间的关系应该是“长期共存,互相补足”,而不是谁取代谁。以此取代彼,没有必要性,也没有可能性。     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

论家庭教育中儿童人格的塑造与培养

父母及家庭环境对儿童人格形成与发展具有十分重要的影响。父母要以身示范,营造和睦、健康、向上的家庭氛围。在儿童人格塑造和培养中,要十分重视智力因素的培养,特别注意早期智力与创造力的开发,重视社会适应能力的培养,包括融入集体生活的能力、人际适应能力和环境适应能力等。     

公司债券违约率的结构化模型研究

采用期权定价和违约率函数的结构化处理方法建立估计公司债券违约率的模型，应用美国国内公司的整体数据给出了将模型具体化的处理方法，得到一个带马尔可夫链的违约率函数。根据实证数据的初步检验，该函数的拟合效果比较理想，可用于估计一般性上市公司群体的债券违约率。文中的处理方法具有良好的可行性，只要拥有模型必需的股权价值、债务价值和违约率的数据，就能按照该方法将模型具体化，拟合出违约率函数，并由此来估计公司债券的违约率。     

NIPA类共聚温敏水凝胶中水的状态和耐热性

用N-异丙基丙烯酰胺（NIPA）与丙烯酸钠（SA）及甲基丙烯酸钠（SMA）共聚合成了两个系列的水凝胶，研究了共聚组成与水凝胶基本性质的关系，并用示差扫描量热法（DSC）和热失重法（TG）研究了此类水凝胶中水的状态和耐热性。