轧制道次间插入冷却对特厚钢板组织与性能的影响

使用实验轧机旁冷却装置配合轧机进行轧制实验，研究轧制道次间不同冷却工艺对特厚钢板组织和性能的影响规律.研究结果表明:采用道次间冷却工艺可以在全厚度方向获得组织细化及强韧性提高效果，采用强冷道次间冷却实验钢1/4处晶粒尺寸可细化至10μm，强度为376MPa，-40℃冲击功为169J;心部晶粒尺寸可细化至15μm，强度为360MPa，-40℃冲击功为123J.本工艺可形成470μm厚表层细晶层，晶粒尺寸可细化至5μm;粗轧道次间插入冷却工艺轧制钢板强度和冲击韧性优于中间坯冷却工艺;随冷却强度增加，钢板内部组织明显细化且强度大幅提高.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

创新研究系统隐性知识生成转化反馈环特性仿真分析

隐性知识反馈环结构是创新研究系统的核心结构,运用组织管理系统动力学理论,进行科研创新系统隐性知识生产转化系统仿真研究,以南昌大学系统动力学创新团队研究系统为例,分析确定该系统的隐性知识量、显性知识量、创新投资量、团队人员数和创新成果量五个核心变量,运用新建的逐枝建模和逐树仿真技术建立五棵流率基本入树模型及其等价流图模型.运用枝向量行列式新增反馈环计算法,计算出系统包含创新成果流位作用于隐性知识流入率的第一类反馈环五条,团队成员数作用于隐性知识流入率第二类正反馈环十条.然后,结合模型的仿真曲线和仿真数据,对第一类反馈环进行极性转移仿真分析和主导反馈环转移仿真分析,对第二类正反馈环进行正反馈环的作用分析,以及"原始创新度"低对这十条正反馈环的制约分析,并基于上述十五条反馈环特性仿真分析结果提出四条创新研究系统发展对策.     

图书管理系统的设计与应用

结合图书馆信息化发展趋势,对图书管理系统的功能特点进行了总结,并详细介绍了图书管理系统的设计与应用.     

“二三结合”开发模式渗流特征研究

L油田B区块开展"二三结合"实验区,"二三结合"开发模式渗流特征对区块的合理高效开发具有重要意义。为了明确其渗流特征,利用油藏数值模拟软件Eclipse建立代表意义的油藏数值模型,研究区块"二三结合"开发模式下原射孔层和补孔层的渗流特征,分析了"二三结合"开发模式下,不同开发阶段综合含水率、采出程度、井底压力、地层压力及含水饱和度的变化特征。研究表明,"二三结合"开发模式先通过水驱开发挖潜原射孔层剩余油,提高厚油层顶部剩余油的采出程度,再通过聚合物驱进一步提高开发效果,通过水驱与聚驱的综合作用,最终得到较好的开发效果。     

连续刚构铁路桥收缩徐变效应监测与分析

对连续刚构铁路桥箱梁温度场及桥梁线形进行长期、连续监测,通过主梁跨中下挠的理论与实测对比揭示了连续刚构铁路桥收缩徐变效应。对比了国内外常用收缩徐变估算模型,选择CEB-FIP徐变模型对黄河特大连续刚构桥进行了有限元分析。采用实测温度数据,以箱梁内测温度、外侧温度、顶底板温度梯度、左右侧温度梯度作为箱梁温度场的评判指标,对箱梁1年内的四季温度场分布进行分析。在基于相同温度场的条件下,通过理论值与实测值对比,发现分析成果与实测结果较吻合,说明混凝土的收缩徐变是引起连续刚构铁路桥跨中下挠的主要原因,对比结果还说明通过改善箱梁顶底板应力差能够改善收缩徐变长期效应。     

不同周围流速和电压下的绝缘子积污特性

为了研究绝缘子在不同电压下表现的积污特性，利用流体力学的相关知识和电场理论，建立了模拟风沙的多物理场仿真模型.研究结果表明，周围流动速度较小时，绝缘子两端的电压增大，积污质量发会有一定程度的增加，且积污与电场力的变化密切相关，结合静电场分析会更准确；周围流动速度较大时，即使电压增大，积污质量也不会发生太大的变化.     

高温作用后砂岩物理力学性质阈值温度的确定——基于机器学习算法

通过采用机器学习算法，提出了高温作用后砂岩物理力学性质变化的阈值温度的确定方法。基于Python语言，利用K-Means、SVM算法，实现了对样本数据的分类和聚类，确定了阈值温度区间，验证了二分类法的合理性和准确性.结果表明，砂岩样本的阈值温度区间为400~600 ℃，阈值温度上下砂岩的物理力学性质存在显著差异，体现为阈值温度区间以下的岩样物理力学性质较为分散，而阈值温度区间以上的岩样物理力学性质较为集中.     

高速电主轴热特性仿真与实验研究

对高速电主轴温度场分布随转速的变化规律进行了研究。通过在外壳上布置一定数量的温度传感器,对不同转速下的外壳温度进行实时测量,并将实验结果与ANSYS的模拟结果进行对比,验证了采用在电主轴外壳上布置多个测点测量与仿真相结合的方法来预测电主轴内部温度场分布的可行性;另外还分析了在不同转速下,高速电主轴关键部位的温升,仿真结果表明:主轴在6000~10000 r/min时,温升呈线性增加,在大于10000 r/min后,温升以指数规律增加。