Tailoring soft magnetic properties of Fe-based amorphous alloys through C addition

It is known that developing Fe-based amorphous alloys with the saturation flux density(B_s) higher than 1.65 T is a major challenge.In present work,effects of C addition on magnetic properties of Fe-based amorphous alloys were systematically studied.It has been found that the addition of C can significantly increase the saturation flux density(B_s) and the magnetic flux density at 800 A/m(B_(800)) of the Fe-B-C-Si-P amorphous alloys.After the addition of C,the B_s of the amorphous alloys increase from 1.61 T(Fe_(83)B_(13)Si_3 P_1) to 1.65-1.71 T(Fe_(83)B_(13-x)C_xSi_3 P_1,x=1.5,2,3 and 4). The Fe_(83)B_(10)C_3 Si_3 P_1 amorphous alloy possesses excellent soft magnetic properties with high B_s of 1.71 T and low H_c of 1.5 A/m.It shows that density increase of the alloys and weakened metalloid-sp/metal-d bonding caused by C addition contribute to the increment of B_s.It suggests that the newly developed high-performance amorphous alloys possess great potential in application.     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

厦门小微企业知识产权托管治理的问题及对策

厦门市知识产权托管工作已由政府单向管理向以政府为主引导，企业、服务机构、行业协会、产业园区以及自贸区等载体参与其中的多元治理体系转变，并取得了良好的成效。但存在顶层设计缺失、托管机构服务能力不足、行业协会作用发挥不充分、氛围营造不够等问题。厦门市应通过加强监管力度、提高小微企业参与托管的意识、提升托管机构的服务能力、激励行业协会发挥作用、加强宣传等措施，进一步完善多元共治的治理体系，提升小微企业知识产权托管治理效能。     

非同分布φ混合序列加权和的强极限收敛性

利用φ混合序列矩不等式和截尾的处理方法,研究非同分布φ混合序列加权和强极限收敛性质的问题,得到了若干新结果,推广并改进了独立同分布情形下的相应结果.     

循环作用对马蹄寺石窟群岩体性能的影响

马蹄寺石窟群地处河西走廊中部,气候条件十分恶劣。由于常年受到温度、湿度、酸碱盐等作用的影响,石窟岩体性能出现了不同程度的劣化现象。通过开展室内模拟试验,研究以上多种恶劣环境的循环作用对于岩体抗压强度、波速、质量的影响规律,同时使用X射线衍射仪(X-ray diffraction,XRD)、X射线荧光光谱(X-ray fluorescence,XRF)和扫描电子显微镜(scanning electron microscope,SEM)对循环作用过程中样品的矿物组分、元素含量和微观形貌进行分析研究。研究结果表明,循环作用使样品中的长石类矿物和方解石含量降低,黏土类矿物含量增加,胶结程度下降,孔隙逐渐发展成为横向微裂隙,导致样品的性能出现不同程度的劣化现象。循环作用对岩体性能的影响程度从大到小依次为冻融循环、耐盐循环、耐碱循环、耐酸循环和温湿循环。     

激光快速成型TC4合金显微组织及力学性能

采用金相显微镜、扫描电镜、电子拉伸机等，研究了激光快速成型TC4合金沉积态在平行沉积方向和垂直沉积方向的组织和力学性能.结果表明:激光快速成型TC4合金沉积态宏观组织沿沉积方向生长的粗大β柱状晶呈明暗相间的条带状结构，具备典型的魏氏组织特征;垂直沉积方向的强度比平行沉积方向的强度高，但塑性低;合金断口为韧窝状断口，垂直沉积方向的断口韧窝尺寸比平行沉积方向的小.     

离散型二维竞争系统中某群体消亡的条件

研究了离散型二维竞争系统的渐近稳定性,得到了这类竞争系统中各类平衡点的坐标及其性质,获得了系统在边界上的平衡点处渐近稳定的一系列充分条件.这些条件等价于该系统中的某个群体在竞争过程中消亡或被淘汰的相应条件.     

四-对羟基苯基卟啉的自组装及光电特性

利用X射线光电子能谱(XPS)测试5,10,15,20-四-(对羟基苯基)卟啉单体和5,10,15,20-四-(对羟基苯基)卟啉自组装二聚体,并通过化学模拟得到卟啉自组装二聚体分子的最优构象.结果表明:两种卟啉化合物中氧原子的类型不同;在单体卟啉中未检测到瞬态表面光电压信号,卟啉自组装二聚体表现出较好的瞬态表面光伏特性;卟啉自组装二聚体的光限幅性质优于卟啉1单体.