城市区域多物流无人机协同任务分配

针对城市区域多无人机协同物流任务分配问题, 综合考虑不同无人机性能、物流时效性、飞行可靠性等影响因素, 以经济成本、时间损失和安全风险最小为目标函数, 构建多无人机协同物流任务分配模型。因问题规模大、求解复杂度高, 设计改进的量子粒子群算法进行求解。首先，为增强粒子遍历性和多样性, 采用均匀化级联Logistic映射进行粒子初始化; 其次，为避免算法陷入局部最优解, 引入基于高斯分布的粒子变异方式; 最后，为提高算法运行效率, 运用自适应惯性权重方法对粒子赋值。仿真实验结果表明，所构建的模型能够实现任务分配多目标优化, 贴近城市区域无人机物流配送实际; 所提算法与传统量子粒子群算法和遗传算法相比, 任务分配代价分别下降了5.9%和6.3%;并进一步对参数权重设置进行分析, 当3个子目标函数权重系数分别为0.225、0.275和0.500, 种群规模为150时, 算法规划的结果最优。     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

非同分布φ混合序列加权和的强极限收敛性

利用φ混合序列矩不等式和截尾的处理方法,研究非同分布φ混合序列加权和强极限收敛性质的问题,得到了若干新结果,推广并改进了独立同分布情形下的相应结果.     

循环作用对马蹄寺石窟群岩体性能的影响

马蹄寺石窟群地处河西走廊中部,气候条件十分恶劣。由于常年受到温度、湿度、酸碱盐等作用的影响,石窟岩体性能出现了不同程度的劣化现象。通过开展室内模拟试验,研究以上多种恶劣环境的循环作用对于岩体抗压强度、波速、质量的影响规律,同时使用X射线衍射仪(X-ray diffraction,XRD)、X射线荧光光谱(X-ray fluorescence,XRF)和扫描电子显微镜(scanning electron microscope,SEM)对循环作用过程中样品的矿物组分、元素含量和微观形貌进行分析研究。研究结果表明,循环作用使样品中的长石类矿物和方解石含量降低,黏土类矿物含量增加,胶结程度下降,孔隙逐渐发展成为横向微裂隙,导致样品的性能出现不同程度的劣化现象。循环作用对岩体性能的影响程度从大到小依次为冻融循环、耐盐循环、耐碱循环、耐酸循环和温湿循环。     

多纤芯弹性光网络中虚拟网络映射模型及算法

为解决多纤芯弹性光网络虚拟化中的虚拟结点映射、链路映射和频谱分配问题,首先建立了一个以最小化占用的频谱数及最小化最大占用频隙号为目标的全局约束优化模型.其次,设计了具有高效的交叉、变异及不可行解可行化算子的全局优化遗传算法,以有效求解该模型得到最优的虚拟节点、链路映射方案.最后,为验证算法的有效性进行了不同的仿真实验.结果表明,所设计的算法能够有效地减小网络中占用的频谱数和最大占用频隙号.     

门捷列夫的“旷缺”与中国公使的感叹

1869年门捷列夫完成了世界上第一张化学元素周期表,除了把当时所知的全部63种元素按原子量大小分组(族)排列外,还在表中留下一些空位,预言了与硼、铝、硅类似的元素的存在及其性质。随后的20多年内,这些空位相继被新发现的元素填补。1877年中国首任驻英公使郭嵩焘听到了门捷列夫的预言与元素镓的发现这一故事,联想到发现海王星的经过,由衷感叹西方科学的精致与功效。     

四-对羟基苯基卟啉的自组装及光电特性

利用X射线光电子能谱(XPS)测试5,10,15,20-四-(对羟基苯基)卟啉单体和5,10,15,20-四-(对羟基苯基)卟啉自组装二聚体,并通过化学模拟得到卟啉自组装二聚体分子的最优构象.结果表明:两种卟啉化合物中氧原子的类型不同;在单体卟啉中未检测到瞬态表面光电压信号,卟啉自组装二聚体表现出较好的瞬态表面光伏特性;卟啉自组装二聚体的光限幅性质优于卟啉1单体.     

高温作用后砂岩物理力学性质阈值温度的确定——基于机器学习算法

通过采用机器学习算法，提出了高温作用后砂岩物理力学性质变化的阈值温度的确定方法。基于Python语言，利用K-Means、SVM算法，实现了对样本数据的分类和聚类，确定了阈值温度区间，验证了二分类法的合理性和准确性.结果表明，砂岩样本的阈值温度区间为400~600 ℃，阈值温度上下砂岩的物理力学性质存在显著差异，体现为阈值温度区间以下的岩样物理力学性质较为分散，而阈值温度区间以上的岩样物理力学性质较为集中.     

高速实时可见光通信技术研究及应用

 介绍了可见光通信技术的发展历史及研究现状。基于带宽拓展技术搭建了1 W荧光型LED做光源、PIN光电二极管做探测器、单路速率610 Mb/s的实时传输演示系统，该系统在传输距离为6.2 m时的误码率为3.48×10^-5。在此基础上搭建了荧光型LED为光源、PIN光电二极管做探测器的、双向100 Mb/s无线光上网演示系统。