基于40Cr高温动态力学性能的磨削表面动态再结晶行为

通过分离式霍普金森压杆(SHPB)实验得到了40Cr合金钢在高温高应变率下真应力-真应变曲线，据此确定了材料发生动态再结晶的临界条件.采用解析法和实验法分别求解了磨削强化层的温度场和塑性应变场分布.结果表明，磨削强化层在磨削深度方向具有较大的温度和塑性应变梯度;150μm强化层内会发生奥氏体转变;磨削表面最高温度可达1060℃.在磨削亚表面60μm内会产生剧烈的塑性变形，达到了再结晶的临界条件.较大的磨削深度使磨削强化层塑性应变增大，再结晶现象越充分，微观组织细化程度越高.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

砂岩在西湖凹陷花港组交互式盖层中的作用初探

西湖凹陷花港组盖层具有砂泥岩交互式发育特征，而与泥岩伴生的砂岩类盖层的油气封闭作用研究较少。采用岩芯、镜下观察及压汞等分析方法，对砂泥岩交互式盖层中的砂岩特征进行了分析。结果表明，盖层中的砂岩可作为有效盖层，砂岩类盖层早期受沉积环境控制，含有较多的泥质而导致早期压实作用较强，加之晚期的黏土矿物转换及胶结物的发育，具备形成良好盖层的条件。在不同地区进行砂岩盖层有效性研究时应以沉积环境为基础，针对不同类型的砂岩进行成岩作用研究，并针对不同类型的砂岩样品进行实验分析以明确砂岩盖层的有效性。     

温度和机械载荷联合作用下油田超深井中硬质涂层膨胀锥与套管的屈服挤毁压强及试验验证

在充分考虑温度载荷、机械载荷、硬质涂层膨胀锥硬度、套管硬度对膨胀锥与套管之间屈服挤毁压强影响的基础上,根据分形理论和接触力学推导出膨胀锥与套管之间屈服挤毁压强的计算公式.数值分析表明:膨胀锥与套管之间的屈服挤毁压强随最终温度、分形粗糙度、线膨胀系数、硬质涂层膨胀锥布氏硬度、中间主应力系数、套管壁厚的增大而增大;当分形维数从1增大时,膨胀锥与套管之间的屈服挤毁压强随分形维数的增大而减小;当分形维数增大到接近于2时,膨胀锥与套管之间的屈服挤毁压强随分形维数的增大而增大;随拉压强度比的增大,膨胀锥与套管之间的屈服挤毁压强减小.屈服挤毁压强的计算值与试验测试值之间的相对误差为-8.9253%～-0.9901%.     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

NIPA类共聚温敏水凝胶中水的状态和耐热性

用N-异丙基丙烯酰胺（NIPA）与丙烯酸钠（SA）及甲基丙烯酸钠（SMA）共聚合成了两个系列的水凝胶，研究了共聚组成与水凝胶基本性质的关系，并用示差扫描量热法（DSC）和热失重法（TG）研究了此类水凝胶中水的状态和耐热性。     

钢板仓受风载作用的有限元分析

对高 14.76m ,直径 12m的螺旋卷边钢板筒仓在空仓风载工况下进行了有限元分析。计算结果表明 ,在风载作用下 ,仓体的强度不是主要问题 ,而仓顶开口处刚度较弱。     

关于差分式放大器输入电阻的研究

差分式放大器在实际应用方面非常广泛,其理论分析方法的深入研究,对生产实践和教学都有重要的意义。采用电路理论分析、差放理论分析、“虚短”理论分析及实验的方法对差分式放大电路进行了研究。     

液压支架压力变送器的电路设计

分析了液压支架的压力特性并提出对压力变送器的技术要求，阐述了压力传感器的选择和外围电路的设计，对压力变送器的信号调理电路进行了仿真分析。