Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

温度和机械载荷联合作用下油田超深井中硬质涂层膨胀锥与套管的屈服挤毁压强及试验验证

在充分考虑温度载荷、机械载荷、硬质涂层膨胀锥硬度、套管硬度对膨胀锥与套管之间屈服挤毁压强影响的基础上,根据分形理论和接触力学推导出膨胀锥与套管之间屈服挤毁压强的计算公式.数值分析表明:膨胀锥与套管之间的屈服挤毁压强随最终温度、分形粗糙度、线膨胀系数、硬质涂层膨胀锥布氏硬度、中间主应力系数、套管壁厚的增大而增大;当分形维数从1增大时,膨胀锥与套管之间的屈服挤毁压强随分形维数的增大而减小;当分形维数增大到接近于2时,膨胀锥与套管之间的屈服挤毁压强随分形维数的增大而增大;随拉压强度比的增大,膨胀锥与套管之间的屈服挤毁压强减小.屈服挤毁压强的计算值与试验测试值之间的相对误差为-8.9253%～-0.9901%.     

Banach空间中二阶Volterra型积分微分方程边值问题解的存在性

利用上、下解法在正规锥上证明了二阶非线性Volterra型积分微分方程边值问题解的存在性。     

一类带限制集值型投入产出方程的存在性定理

引入了一类带限制的集值型投入产出方程.通过利用某些非线性分析方法,得到了一些存在及连续相依性结果.     

用可调光锥系统获得卫星照片大尺度空间频谱的初步研究

将可调光锥系统直接应用于获得大尺度空间频谱的研究，得到了较满意的实验结果。     

麻花钻内锥面刃磨试验

阐述了内锥面法刃磨麻花钻的原理以及在工具磨床上进行磨削工艺试验的方法。通过试验刃磨出了合格的麻花钻,验证了内锥面法刃磨麻花钻理论,并对内锥面刃磨试验中存在的问题进行了分析讨论。     

一个非线性互补问题

本文给出了局部一致凸自反的 Banach 空间上互补问题的一个解的存在性定理。这个结果是在较弱的 Karmardian 条件下得到的。     

玻璃器皿压机转位机构凸轮——槽轮机构的研究

论述了一种拨销回转半径可变的凸轮——槽轮机构。叙述了玻璃器皿压机转位机构的运动要求。研究了用这种机构驱动工作台间歇转动的设计方法。     

一类非连续算子不动点存在的充分必要条件

文章证明了不加连续条件的一类凹算子存在不动点的充分必要条件     

二阶常微分ZPT方程Suturn-Liouville问题多个正解的存在性

研究了二阶常微分方程Stum—Liouville问题，通过使用不动点指数这一工具，在适当条件下建立了这类边值问题多正解存在的充分条件