“二三结合”开发模式渗流特征研究

L油田B区块开展"二三结合"实验区,"二三结合"开发模式渗流特征对区块的合理高效开发具有重要意义。为了明确其渗流特征,利用油藏数值模拟软件Eclipse建立代表意义的油藏数值模型,研究区块"二三结合"开发模式下原射孔层和补孔层的渗流特征,分析了"二三结合"开发模式下,不同开发阶段综合含水率、采出程度、井底压力、地层压力及含水饱和度的变化特征。研究表明,"二三结合"开发模式先通过水驱开发挖潜原射孔层剩余油,提高厚油层顶部剩余油的采出程度,再通过聚合物驱进一步提高开发效果,通过水驱与聚驱的综合作用,最终得到较好的开发效果。     

阳离子微粒聚合物在造纸工业中的应用

采用乳剂和溶液的聚合技术制备了不同电荷密度和胶体性质的阳离子微粒聚合物(CPMP)。论文探讨了阳离子微粒聚合物在造纸工业中的应用。研究表明用阳离子或阴离子的聚合物与阳离子微粒聚合物联合使用可以改善纸张的匀度和留着率。其机理可能是由干阳离子微粒聚合物的加入产生了更有效的架桥絮聚。另外阳离子微粒聚合物也是一种良好的施胶剂，研究结果表明施胶效果与聚合物添加量．电荷密度和微粒尺寸有关。通过施胶张可以获得更好的光学和物理性能。     

The Gas Sensitivity of Polypyrrole Film Fabricated by in Situ Polymerization

1 Results Polypyrrole (PPy) is a typical conducting polymer with high conductivity and good stability,and has been widely used for detection of gases including ammonia and nitroxide[1].However the reversiblity and selectivity of the response to these gases are always not satisfying.In the paper,conductive PPy film was deposited on the interdigital electrode modified by one bilayer of poly(diallyldimethylammonium chloride) and poly(sodium styrenesulfonate),by in-situ polymerization with FeCl3 as oxidizin...     

New Membranes Based on Polybenzimidazole for Polymer Fuel Cells

1 Results Acid-doped polybenzimidazoles[1] are particularly appealing because of high proton conductivity with no or low humidification and promising fuel cells performances. PBI, in fact, contains basic functional groups which can easily interact with strong oxo-acids, such as H3PO4 and H2SO4. The acid partially protonates the polymer and partially is freely dispersed in the polymer backbone, so allowing proton migration via Grotthuss mechanism along the anionic chains[2]. Anyway, a technological limit...     

STUDY ON POLYPYRROLE-VISCOSE CONDUCTING FIBER

The conductivity of Polypyrrole-viscose conducting fiber prepared with author's method can be shown up to as high as 2.106x10~(-2) S/cm. The main factors influencing the conductivity are the concentration of FeCl_3 used as dopant and initiator, the treatment time of viscose fiber as base material in FeCl_3 solution, temperature and polymerization time. It is found that the orientation and crystallization degree of viscose fiber keep constant before and after conducting treatment and the mechanical properties of conducting fiber is the same as that of base material. In addition, the distribution of polypyrrole in viscose fiber, and its effect on the conductivity were investigated in details by TEM.     

一种新型粘土稳定剂的合成与应用研究

本文简要报导了有机阳离子聚和物(氯化N,N—二甲基二烯丙基铵—二氧化硫)的合成方法,并对其作为粘土稳定剂的性能进行了评价。结果表明,该共聚物稳定粘土的能力高于目前国内外广泛使用的同类聚合物TDC。     

纳米聚合物复合材料开发与技术

简述了聚合物 /纳米无机物复合材料的概况、性能及制造方法     

高分子流体材料拉伸流动研究

成纤材料的可纺性是合成新的成纤材料或是度量现有材料的成纤条件的关键性参数,拉伸率是衡量材料的可纺性的依据,本文就纤维纺丝拉伸的类型和特点进行分析研究,其结果与材料本构方程联立求解,可分析求解高分子材料拉伸流动中的流动参数.     

综采工作面过超大断层的技术应用

介绍了杜儿坪矿68214工作面大断层,提出了通过大断层时采取的技术措施和打注高分子材料（马丽散N）的技术措施。     

外贴FRP加固钢筋混凝土梁用量显式设计方法

对外贴FRP（纤维增强复合材料）加固钢筋混凝土梁抗弯极限承载力的求解问题，ACI440F规范及我国CECS146：2003规程都给出了相应的求解公式，但均为验算形式．这在面向设计，即计算给定目标承载力下的FRP用量时，并不方便．针对矩形截面形式，通过引入原构件配筋特征参数和FRP配筋特征参数，推导出量纲-形式的弯矩增量与参数之间的关系表达式，并给出显式求解FRP用量的计算方法．在此基础上，进一步通过定义截面形状系数，将这一显式求解方法推广至T形及更为一般性的截面形式．