Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

非锚固式大型立式热质储罐强度分析

针对大型储罐在多种载荷作用下易发生强度破坏的问题，以某热质储罐为研究对象，利用有限元法分析热质储罐在自重、内压、液柱静压力、风载荷、地震载荷、雪载荷以及温度载荷作用下的应力强度以及变形，模拟大角焊缝区域翘曲情况，并依照JB4732—1995进行强度评定，为此类大型立式储罐的设计提供参考。     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

NIPA类共聚温敏水凝胶中水的状态和耐热性

用N-异丙基丙烯酰胺（NIPA）与丙烯酸钠（SA）及甲基丙烯酸钠（SMA）共聚合成了两个系列的水凝胶，研究了共聚组成与水凝胶基本性质的关系，并用示差扫描量热法（DSC）和热失重法（TG）研究了此类水凝胶中水的状态和耐热性。     

矩形型钢弯曲回弹曲率半径r值的确定

文章在分析矩形型钢弯曲变形过程及应力与应变等方面的关系的基础上，推导出工件曲率半径与工件回弹后曲率半径之间的关系，从而确定了凸模半径。     

地下洞室形状优化设计

洞室开挖会使围岩周边产生应力集中 ,产生拉应力与压应力。围岩出现拉应力对洞室稳定十分不利 ,通常通过改变洞室形状和轴比来消除围岩中的拉应力。本文提出一种使洞室拉应力σθ=0 ,而压应力最小的确定洞室最优几何形状的方法。     

钢板仓受风载作用的有限元分析

对高 14.76m ,直径 12m的螺旋卷边钢板筒仓在空仓风载工况下进行了有限元分析。计算结果表明 ,在风载作用下 ,仓体的强度不是主要问题 ,而仓顶开口处刚度较弱。     

论峡江地区“烧龙”与“烧畬”的区别和联系

唐宋时期峡江地区“击鼓焚山”的民俗活动是远古时代尚巫之风的残存,其目的是为烧龙祈雨以禳除旱灾;而“烧畬下种”则是自远古“刀耕火种”传承下来的一门农耕技术,但由于“占卜伺雨”的仪式亦使它带上了一些巫风色彩。二者既有明显的区别又有一定的联系。     

关于差分式放大器输入电阻的研究

差分式放大器在实际应用方面非常广泛,其理论分析方法的深入研究,对生产实践和教学都有重要的意义。采用电路理论分析、差放理论分析、“虚短”理论分析及实验的方法对差分式放大电路进行了研究。