复合跟踪微分器在电容式位移传感器中的应用

针对从含噪原始信号中提取位置以及速度信息,经典跟踪微分器存在不能很好兼顾相位滞后和噪声放大问题、参数多,调试复杂等不足.在跟踪微分器等效线性分析基础上,提出复合形式跟踪微分器,用于电容式位移传感器位置信号跟踪以及速度信号估计,通过MATLAB\SIMULINK仿真以及实验平台测试,结果表明:在跟踪频率1 Hz、幅值1含噪声正弦信号中,复合跟踪微分器能光滑逼近原始位置信号,且能有效进行速度估计,相较于经典跟踪微分器,复合跟踪微分器跟踪相位滞后小0.03 rad,能更好兼顾跟踪信号相位滞后及速度信号噪声放大.     

Self-rolled TiO_2 microscroll/graphene composite for electrochemical dopamine sensing

Dopamine is an important neurotransmitter,and nonenzyme electrochemical sensor of dopamine detection based on highly active material is urgently demanded.In this work,an electrochemical sensor with high sensitivity and selectivity based on self-rolled TiO_2microscroll/graphene composite was developed and validated for dopamine sensing.The device exhibited a superior performance for dopamine detection with a detection limit of 4.25×10~(-9)mol L~(-1),and in the dopamine concentration range of 0.06–90μmol L~(-1),the oxidation currents increased linearly with the concentration.The remarkable performance enhancement was mainly ascribed to the increased surface area due to the porous surface of the TiO_2nanomembrane and highly conductive graphene therein.In addition,we have demonstrated that the sensor could be effectively used on detecting dopamine concentrations in urine samples.Our work demonstrates that the current microscroll-based device is promising in the field of real-time health monitoring for future human community.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

基于免疫粒子群优化的移动Sink路径规划算法

为了减少能量空洞和延长网络生命周期，在无线传感网中采用移动 Sink 的方式收集节点采集的数据是解决能 量效率问题的有效措施．采集路径的规划问题类似于旅行商问题，无法得到多项式时间的解．提出了将人工免疫算法和粒子群算法相结合，针对移动 sink 数据收集的路径规划问题寻求近似最优解，仿真结果表明: 与其他算法进行性能比较，所提出的优化算法能够有效减少能耗和缩短遍历路径．     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

发动机传感器的测试

发动机传感器的测试是进行控制和诊断的基础,故有必要对传感器输出信号的性质、特征及电路加以阐述.     

新型流量传感器在呼吸机上的应用

介绍了AWM720P1新型气体流量传感器的工作原理、性能、特点．针对呼吸机的工作特点，分析了IPPV的流速模型、流速的测量方法、传感器的校正数据处理方法．     

NIPA类共聚温敏水凝胶中水的状态和耐热性

用N-异丙基丙烯酰胺（NIPA）与丙烯酸钠（SA）及甲基丙烯酸钠（SMA）共聚合成了两个系列的水凝胶，研究了共聚组成与水凝胶基本性质的关系，并用示差扫描量热法（DSC）和热失重法（TG）研究了此类水凝胶中水的状态和耐热性。     

关于差分式放大器输入电阻的研究

差分式放大器在实际应用方面非常广泛,其理论分析方法的深入研究,对生产实践和教学都有重要的意义。采用电路理论分析、差放理论分析、“虚短”理论分析及实验的方法对差分式放大电路进行了研究。