Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

页岩气低伤害超临界CO2凝胶压裂液研究

针对常规水压裂液会对页岩造成伤害，容易产生水锁，不易返排，还造成水资源消耗和污染环境等问题，制备了低伤害二氧化碳凝胶压裂液。将自备的F2EU和F4EU增稠剂加入到超临界CO₂基液中，探究两种增稠剂的加入量对CO₂凝胶压裂液黏度的影响，综合考虑成本与效果，优选了2%的F4EU增稠剂，可将CO₂的黏度增至15.4 mPa·s。研究了温度、压力以及剪切速率对凝胶压裂液黏度的影响。实验结果表明，随着温度升高黏度总体降低，但中间出现一个短暂升高阶段；随着压力上升压裂液黏度增加；随着剪切速率的增加压裂液黏度下降，属于一种典型的剪切变稀的假塑性流体。F4EU超临界CO₂凝胶压裂液的平均伤害率为1.39%，远远小于常规压裂液对岩芯的伤害率。实验表明，F4EU超临界CO₂凝胶压裂液在页岩气压裂开采中具有良好的应用前景。     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

具有sn-网的空间

证明了具有σ—点有限sn—网及σ—局部可数sn—网的空间可刻划为度量空间在某些确定映射下的象.     

Supercritical Fluid Carbon Dioxide in the Extraction of Lanolin and Its Alcohol

The use of supercritical fluid carbon dioxide (SF-CO_2) in extraction of lanolin and its alcohol issuperior to the conventional solvent extractionmethod. Its distinctive advantages include highextractive ratio, nontoxic and nonflammablesolvents, and minimal by-product pollution. The     

感应熔敷WC/Ni基复合涂层的组织和性能

采用高频感应熔敷技术，以Ni60A自熔合金粉末、微纳米碳化钨粉末为原料，在16Mn钢表面制备出以微纳米WC颗粒为增强相的Ni基金属陶瓷涂层，并测试了涂层的显微硬度。利用磨擦磨损试验机，以45#钢为对磨偶件，评价了涂层的滑动干磨擦性能。实验结果表明：涂层的硬度为890～910,磨擦系数为0．3-0．4，耐磨性比16Mn钢提高4倍以上。     

Abrupt climate change：Debate or action

Global abrupt climate changes have been documented by various climate records, including ice cores, ocean sediment cores, lake sediment cores, cave deposits, loess deposits and pollen records. The climate system prefers to be in one of two stable states, i.e. interstadial or stadial conditions, but not in between. The transition between two states has an abrupt character. Abrupt climate changes are, in general, synchronous in the northern hemisphere and tropical regions. The timescale for abrupt climate changes can be as short as a decade. As the impacts may be potentially serious, we need to take actions such as reducing CO2 emissions to the atmosphere.     

La2分子结构与基态分子势能函数

用相对论有效原子实势，在密度泛函理论(DFT)和组态相关理论(QCISD)水平上优化计算了La2分子的结构．根据原子分子反应静力学原理，导出La2分子可能的电子状态和离解极限，用DFT中的B3LYP方法计算了基态X1∑g^ 势能曲线，拟合得到Murrell-Sorbie解析势能函数，并首次计算得到基态X1∑g^ 的谐振频率、热力学性质、力学与光谱数据。     

CO2跨临界循环系统润滑油分析

为保证CO2跨临界循环系统的稳定运行，选择与之相适应的润滑油，在分析摩擦润滑特性的基础上，采用实验数据对比的方法，对POE、PAG、PAO和烷基芳香烃4类合成润滑油在CO2跨临界循环系统中的混合性、流动性、可溶性、黏度、长期稳定性及润滑性等性能进行了分析，结果表明POE类润滑油是CO2跨临界循环系统的一种相对较好的选择。