螺栓连接大变形梁非线性振动特性的实验研究

柔性机械臂、大型可展开天线等机械结构的动作精度受运动过程中大变形几何非线性和连接处接触非线性的影响十分显著。以含螺栓连接结构的大变形梁作为研究对象，针对动力学建模和振动特性开展了实验研究，通过数值计算验证了实验发现的非线性振动特性。搭建了含螺栓连接柔性大变形梁的实验台架，开展了敲击和正弦激振的实验测试。实验结果表明，螺栓连接的柔性梁较连续梁的（无螺栓连接）模态频率降低，阻尼增加，反映出随着激励能量增大，模态频率降低的非线性模态特征。改变螺栓连接位置会显著影响结构的模态频率，其变化规律可由求解线性矩阵特征值定性反映。     

PI-强LU富足半群

通过对C-L^U-富足半群的刻画,给出了PI-强L^U富足半群的结构定理。     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

径向井排引导水力压裂裂缝扩展机理研究

为探究径向井排系统对裂缝的影响，明确水力裂缝的扩展规律，利用扩展有限元理论建立了流固耦合三维裂缝扩展模型，模拟了受径向井排引导的水力裂缝扩展过程。重点分析了3种影响因素（径向井排方位角、水平地应力差、径向井孔径）对水力裂缝的引导机理。首次提出了"引导因子"的概念，并将其作为有效评价径向井排引导效果的量化参数。研究发现，径向井方位角、水平地应力差、径向井井径会对水力裂缝的引导效果产生影响：较小的径向井方位角、水平地应力差以及较大的井径都使径向井排具有较强的引导能力和较好的引导效果，反之亦然。同时，较大井径对增加水力裂缝宽度有明显作用。最后，利用大尺寸真三轴水力压裂模拟试验证实了数值模拟结果具有一定的准确性。     

数学专业师范生教学技能的调查研究--以四川文理学院为例

教学技能是教师最重要的专业素质，是师范生在大学期间需要掌握的基础职业技能。通过调查研究表明，数学专业大学生教学基本功发展不平衡，不同年级学生的教学技能水平存在显著差异。教学实践、课改认知、教学交流、自主练习是影响教学技能的四个主因子。男女生在表达技能、教学设计技能、几何作图技能等方面差异显著，而在教材分析、多媒体使用方面不存在显著性差异。要通过完善教学技能培养机制，夯实师范基础技能培养，改革教学技能培养方式等途径，合力提高师范生的教学技能，增强就业竞争力。     

基于网络最大流的城市雨水管网系统脆弱性评价

为了对城市雨水管网系统进行针对性的改建,在暴雨天提高事故抢修速度,需要对城市雨水管网系统进行脆弱性评价并找出脆弱管段.首先介绍了城市雨水管网系统排出雨水的干扰因素,提出了城市雨水管网系统脆弱性的概念,并逐一分析了影响城市雨水管网系统的因素,综合考虑各方面因素,建立了城市雨水管网系统的脆弱性评价模型.在此基础上,结合图论中网络最大流理论,寻找城市雨水管网系统中的脆弱管段.最后以西安某高校的雨水管网系统为例进行研究,测得了该高校雨水管网系统的脆弱度为0.877,证明该区域雨水管网脆弱性较低,不易形成内涝,并找出该高校雨水管网的脆弱管段.     

正规矩阵特征值扰动的新估计

设A,B均为正规矩阵,关于正规矩阵的特征值扰动,有结论 (n∑i=1︱μτ(i)-λi︱2)(1/2)≤n(1/2)‖E‖F,其中λi,μi分别为A,B的特征值.通过新的方法证明给出特征值扰动上界的新估计,并改进了以上结论.     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

各向同性介质与单轴晶体界面上e光波法线的折射

根据光的电矢量满足的边条件，对各向同性介质与单轴晶体界面上e光波法线的折射进行了具体的讨论，得到了确定e光波法线在单轴晶体中传播方向的公式，并对几种特殊情况进行了具体讨论。指出了由所得结果可以确定e光光线的行进方向。