绢纺生产用抗静电剂的研究——SS1与SS2绢纺抗静电剂

本文对绢纺生产用抗静电剂的配方进行了研究,研制出SS1及SS2绢纺抗静电剂。应用表明,采用此类抗静电剂,不但降低了生产中的静电,而且提高了梳折;在圆梳系统中提高了3.23％,在精梳系统中提高了3.1％;同时精绵的长度和强力也有所增加,从而提高了经济效益。     

THE PRACTICE OF ACRYLIC SIROSPUN YARN ON THE SEMI WORSTED SPINNING FRAME

The technique of sirospun process is applied on a modified semi-worsted balloonless spinningframe to investigate the effect of spindle-speed,yarn-twist and strand-spacing on yarn properties.Yarn breaking strength,breaking extension,evenness and imperfection are examined on the basisof CCD experimental design.Yarn hairiness is particularly concerned,being found that all spinningparameters tested have significant effects on hairiness and that the minimum number of hairs oc-curs at the strand-spacing of 14.4 mm.Compared to conventional single spun yarn,experimentshave revealed the greatest advantage of using sirospun process is that all sirospun yarns have muchless hairiness.A new sirospun yarn fault,so called“loop”,has also been examined.The most likely cause forthis yarn fault is the strand-tension unbalance between the two strands when low tension spinningis applied.Further analysis and some initial tests have been carried out in the hope of overcomingthis loop fault which is an important obstacle to the application of balloonless spinning.     

剪切速率对高浓度再生丝素水溶液构象的影响

对高浓度的再生丝素水溶液（15％～37％）在不同剪切速率下（1000s-1和2000s-1）的构象变化进行了研究，对剪切前后的溶液进行了DSC和Raman对比测试。发现经过剪切，丝素溶液更客易发生从无规线团或α-螺旋向β-折叠构象的转变，且转变的程度随所受剪切速率的增加而提高。而且当丝素浓度低于27％时对剪切不敏感；超过30％时则对剪切敏感。     

再生丝素固体的微细结构

研究了蚕丝丝素水溶液经不同方式干燥后，所得到的再生丝素固体的微细结构，以及存放过程中丝素的结构变化，指出经30℃热风干燥或经高于－20℃冷冻干燥后，所得到的丝素固体的结构是无定形和Silk I共存，在室内温度湿度环境中存放后，部分无定形结构转化为Silk I；蚕丝丝素水溶液经－80－－20℃冷冻干燥后，所得到的丝素膜的结构主要是无定形，含少量Silk II，存放过程中部分无定形结构转化为SilkI；室温放所自然形成的丝素凝胶中，丝素的结构是无定形和Silk Ⅱ共存；丝素水溶液表面膜中甘氨酸和丙氨酸的含量较高，表面膜的结构主要是Silk I和Tilk Ⅱ结晶度高。     

THE INFLUENCE OF SPINNING CONDITION ON STRUCTURE & PROPERTIES OF MASS-DYED SUPERFINE PP AS-SPUN FILAMENTS

The effect of colorant additive on the rheology of PP polymer melt and the influence of spinning conditions on the crystalline and orientation structure of mass-dyed as-spun PP filament are reported. The △E~~~ value for all colored chips is higher than that of blank chip to a varying degree. The crystallinity and orientation degree of dyed PP as-spun filament decrease with increasing melt temperature, decreasing spinning speed and increasing denier per filament (dpf), while the crystallinity of dyed as-spun filament increases with the content of colorant additive as a nucleation agent.     

管道纺包芯纱的研究

本文研究了在管道纺纱机上不添加构件而进行包芯纱的纺制。分析了其包芯纱的成纱机理。观察了实际成纱的横截面,证实了棉纤维能够均匀地、完全地包覆在芯丝的周围。也对不同性质的芯丝所纺包芯纱的结构作了观察,并对不同成纱的性质随速度增加而变化的规律作了研究。     

NiAl金属间化合物熔体旋转法制备工艺参数研究

研究了金属间化合物快速凝固薄带的成型过程和影响薄带质量的工艺参数。提出了熔体在喷嘴处进行层流流动的经验关系式，给出了金属间化合物快速凝固薄带制备的最佳工艺参数。     

二十一世纪纺纱工程展望

二十一世纪,一些相关高新技术的发展和应用,将对传统工程产生巨大的影响和推动。文章在此基础上,对新世纪前半叶纺纱技术、纺纱设备以及纺纱工厂自动化的发展进行了展望。     

Cu（Ⅱ） effect on the conformation of regenerated silk fibroin in dilute aqueous solution

Much attention has been paid to the natural mechanism of silkworm spinning due to the impressive mechanical properties of the natural fibers. In this work, we studied the effect of Cu（Ⅱ） ions on the secondary structure of Bombyx mori regenerated silk fibroin （SF） in dilute solution by circular dichroism （CD）. The results indicate that a given amount of Cu（Ⅱ） induces the SF conformational transition from random coil to β-sheet, however, further addition of Cu（Ⅱ） is unfavorable for this conversion. Meanwhile, the conformational changes induced by Cu（Ⅱ） follow a nucleation-dependent aggregation mechanism, which is similar to that found in Prion protein （PrP） denaturation and Aβ-peptide aggregations, leading to the neurodegenerative disease. This work would help one understand further the natural spinning process of silkworm. Additionally, it would be significant for the study of the nervous system diseases, because silk fibroin, extracted in large amounts from Bombyx mori silkworm gland, could be a proper model to study PrP denaturation and Aβ-peptide aggregations.     

喷丝头组合花板的真空熔炼

化纤生产行业的粘胶，经过装在组合花板上的喷丝头在酸浴里形成化学纤维。粘胶为碱性物质，酸浴的化学成份为稀硫酸、磷酸，酸浴温度为57℃左右，组合花板内压力为10kg／cm^2，要求组合花板材料在有足够的强度下，具有高耐腐蚀性能。