共享自动驾驶汽车使用意愿模型及其影响因素

为了构建共享自动驾驶汽车(shared autonomous vehicles，SAV) 的使用意愿模型并分析其影响因素，通过使用时机和使用频率来体现公众对SAV的使用意愿；采用验证性因子分析将态度潜变量转化为潜变量得分，以此将态度潜变量引入传统的有序Logit模型；提出SAV使用意愿的有序Logit模型构建方法，并建立基于个人属性、通勤特征、态度潜变量的SAV使用意愿模型.研究发现:是否使用过滴滴拼车、工作单位停车费、自动驾驶态度对使用时机和3种价格(1，2，3元/km) 下的使用频率有显著影响；使用过滴滴拼车、工作单位收取停车费、支持自动驾驶的群体倾向于频繁地、更早地使用SAV出行；公众期望以1元/km或 2元/km即不超过目前滴滴拼车的价格使用SAV.     

Tailoring soft magnetic properties of Fe-based amorphous alloys through C addition

It is known that developing Fe-based amorphous alloys with the saturation flux density(B_s) higher than 1.65 T is a major challenge.In present work,effects of C addition on magnetic properties of Fe-based amorphous alloys were systematically studied.It has been found that the addition of C can significantly increase the saturation flux density(B_s) and the magnetic flux density at 800 A/m(B_(800)) of the Fe-B-C-Si-P amorphous alloys.After the addition of C,the B_s of the amorphous alloys increase from 1.61 T(Fe_(83)B_(13)Si_3 P_1) to 1.65-1.71 T(Fe_(83)B_(13-x)C_xSi_3 P_1,x=1.5,2,3 and 4). The Fe_(83)B_(10)C_3 Si_3 P_1 amorphous alloy possesses excellent soft magnetic properties with high B_s of 1.71 T and low H_c of 1.5 A/m.It shows that density increase of the alloys and weakened metalloid-sp/metal-d bonding caused by C addition contribute to the increment of B_s.It suggests that the newly developed high-performance amorphous alloys possess great potential in application.     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

地理国情普查地表覆盖内业解译的质量问题研究

地表覆盖内业解译是地理国情普查的一道重要工序。地理国情地表覆盖内业解译现存图斑平面位置精度不足、分类错误多种多样等普遍问题,问题突出典型。文中针对这些问题图文并茂、清晰明了的进行了说明,并从多方面分析问题产生的原因,提出加强对技术指标和采集原则的学习和理解,加强内业与外业的结合,充分发挥解译样本的作用等建议,以有效提高内业解译的质量。     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

非同分布φ混合序列加权和的强极限收敛性

利用φ混合序列矩不等式和截尾的处理方法,研究非同分布φ混合序列加权和强极限收敛性质的问题,得到了若干新结果,推广并改进了独立同分布情形下的相应结果.     

循环作用对马蹄寺石窟群岩体性能的影响

马蹄寺石窟群地处河西走廊中部,气候条件十分恶劣。由于常年受到温度、湿度、酸碱盐等作用的影响,石窟岩体性能出现了不同程度的劣化现象。通过开展室内模拟试验,研究以上多种恶劣环境的循环作用对于岩体抗压强度、波速、质量的影响规律,同时使用X射线衍射仪(X-ray diffraction,XRD)、X射线荧光光谱(X-ray fluorescence,XRF)和扫描电子显微镜(scanning electron microscope,SEM)对循环作用过程中样品的矿物组分、元素含量和微观形貌进行分析研究。研究结果表明,循环作用使样品中的长石类矿物和方解石含量降低,黏土类矿物含量增加,胶结程度下降,孔隙逐渐发展成为横向微裂隙,导致样品的性能出现不同程度的劣化现象。循环作用对岩体性能的影响程度从大到小依次为冻融循环、耐盐循环、耐碱循环、耐酸循环和温湿循环。     

浙西南环敕木山带畲族妇女“雄冠式”头冠解析

浙西南的环敕木山一带，是畲族迁徙到浙江省境内最早的聚居地，这里的畲族妇女传统“雄冠式”头冠，极具民族特色，整体造型呈三角形，用木、布、银等装饰材料，表现出凤凰吟啭的形态，造型精美，色彩斑斓，蕴含着对祖先图腾的崇敬。通过具体描述其头冠的制作、佩戴方法以及佩戴习俗，力求完整地再现浙西南的环敕木山一带畲族妇女“雄冠式”头冠所承载的畲族文化。     

创新开展新时期科技名词规范化工作,努力发挥支撑服务作用

科技名词规范化工作具有深厚的历史基础和现实需要,是支撑科技创新和经济社会发展的一项基础性系统工程。当前,中国特色社会主义进入新时代,我们要深刻领会“新时代”的丰富内涵,深化认识科技名词规范化工作的特殊意义,创新开展各项工作,更好肩负起新时代赋予的历史使命。