Exendin-4螺旋结构对生物活性及稳定性的影响

针对Exendin-4的螺旋结构特点, 采用去掉螺旋序列、 用3个连续Ala替换螺旋以及Gln13替换为Tyr13的方式对N端α-螺旋及C端α-螺旋进行改造, 设计出4个结构模拟物. 通过圆二光谱和荧光光谱进行结构分析, 结合模拟物生物活性实验, 分析Exendin-4螺旋结构与生物活性的关系. 结果表明：  Exendin-4的N端螺旋比C端螺旋对生物活性影响更大； 在抗二肽基肽酶（DPPⅣ酶）的稳定性实验中, C端螺旋比N端螺旋具有更好维系Exendin-4稳定性的作用； 螺旋结构中Tyr13可作为提高Exendin-4生物活性的重要优化位点.     

轧制道次间插入冷却对特厚钢板组织与性能的影响

使用实验轧机旁冷却装置配合轧机进行轧制实验，研究轧制道次间不同冷却工艺对特厚钢板组织和性能的影响规律.研究结果表明:采用道次间冷却工艺可以在全厚度方向获得组织细化及强韧性提高效果，采用强冷道次间冷却实验钢1/4处晶粒尺寸可细化至10μm，强度为376MPa，-40℃冲击功为169J;心部晶粒尺寸可细化至15μm，强度为360MPa，-40℃冲击功为123J.本工艺可形成470μm厚表层细晶层，晶粒尺寸可细化至5μm;粗轧道次间插入冷却工艺轧制钢板强度和冲击韧性优于中间坯冷却工艺;随冷却强度增加，钢板内部组织明显细化且强度大幅提高.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

连续刚构铁路桥收缩徐变效应监测与分析

对连续刚构铁路桥箱梁温度场及桥梁线形进行长期、连续监测,通过主梁跨中下挠的理论与实测对比揭示了连续刚构铁路桥收缩徐变效应。对比了国内外常用收缩徐变估算模型,选择CEB-FIP徐变模型对黄河特大连续刚构桥进行了有限元分析。采用实测温度数据,以箱梁内测温度、外侧温度、顶底板温度梯度、左右侧温度梯度作为箱梁温度场的评判指标,对箱梁1年内的四季温度场分布进行分析。在基于相同温度场的条件下,通过理论值与实测值对比,发现分析成果与实测结果较吻合,说明混凝土的收缩徐变是引起连续刚构铁路桥跨中下挠的主要原因,对比结果还说明通过改善箱梁顶底板应力差能够改善收缩徐变长期效应。     

磁流变液中磁性颗粒成链与团聚的临界特征分析

热运动对纳米级磁流变液系统的颗粒团聚行为和宏观流变特性扰动影响不可忽视.为研究施加外磁场后系统微结构与热运动间的关系，探讨在不同颗粒粒径情况下热运动能量在系统总能量中的占比.采用CCD设计方法，分析Monte Carlo仿真获取的颗粒位形信息，生成关于外磁场磁感应强度、颗粒粒径和体积分数的系统热耦合系数<λ>回归模型;成链团聚的临界颗粒粒径计算值比文献经验值高出约23%，证实在考虑系统内多因素的综合影响下，纳米级磁流变液具有更严格的流变现象临界发生条件.     

基于热中子探测评价裂缝的示踪剂特性研究

针对裂缝热中子示踪探测方法,从中子双组扩散理论入手结合蒙特卡洛数值模拟方法,分析压裂前后地层热中子分布影响因素,并模拟不同类型示踪剂及含量的热中子裂缝响应规律,筛选最佳示踪剂并给出其在支撑剂中含量的上、下限。结果表明:压裂前后热中子计数变化量主要受裂缝宽度和标记支撑剂中示踪剂含量的影响;钆对裂缝宽度变化反应最灵敏,钆元素是作为标记支撑剂的最佳示踪元素;随支撑剂中Gd 2O 3含量的增加,热中子计数率降低,热中子计数变化量D增加;示踪剂中氧化钆的上、下限值随裂缝宽度呈指数降低,且当裂缝宽度为1.0 cm时,Gd 2O 3的质量分数上限为0.68%,下限为0.03%。     

高温作用后砂岩物理力学性质阈值温度的确定——基于机器学习算法

通过采用机器学习算法，提出了高温作用后砂岩物理力学性质变化的阈值温度的确定方法。基于Python语言，利用K-Means、SVM算法，实现了对样本数据的分类和聚类，确定了阈值温度区间，验证了二分类法的合理性和准确性.结果表明，砂岩样本的阈值温度区间为400~600 ℃，阈值温度上下砂岩的物理力学性质存在显著差异，体现为阈值温度区间以下的岩样物理力学性质较为分散，而阈值温度区间以上的岩样物理力学性质较为集中.     

高速电主轴热特性仿真与实验研究

对高速电主轴温度场分布随转速的变化规律进行了研究。通过在外壳上布置一定数量的温度传感器,对不同转速下的外壳温度进行实时测量,并将实验结果与ANSYS的模拟结果进行对比,验证了采用在电主轴外壳上布置多个测点测量与仿真相结合的方法来预测电主轴内部温度场分布的可行性;另外还分析了在不同转速下,高速电主轴关键部位的温升,仿真结果表明:主轴在6000~10000 r/min时,温升呈线性增加,在大于10000 r/min后,温升以指数规律增加。     

温度和机械载荷联合作用下油田超深井中硬质涂层膨胀锥与套管的屈服挤毁压强及试验验证

在充分考虑温度载荷、机械载荷、硬质涂层膨胀锥硬度、套管硬度对膨胀锥与套管之间屈服挤毁压强影响的基础上,根据分形理论和接触力学推导出膨胀锥与套管之间屈服挤毁压强的计算公式.数值分析表明:膨胀锥与套管之间的屈服挤毁压强随最终温度、分形粗糙度、线膨胀系数、硬质涂层膨胀锥布氏硬度、中间主应力系数、套管壁厚的增大而增大;当分形维数从1增大时,膨胀锥与套管之间的屈服挤毁压强随分形维数的增大而减小;当分形维数增大到接近于2时,膨胀锥与套管之间的屈服挤毁压强随分形维数的增大而增大;随拉压强度比的增大,膨胀锥与套管之间的屈服挤毁压强减小.屈服挤毁压强的计算值与试验测试值之间的相对误差为-8.9253%～-0.9901%.