基于多材质复合管柱的裸眼井壁支撑工艺及应用

已完钻超深裸眼水平井侧钻技术是经济、高效开发油藏剩余油的主要手段之一，传统的磨铣钢套管开窗侧钻技术存在下入摩阻大、磨铣耗时长导致开窗失败等问题。为此，提出了基于多材质复合管柱的超深水平井裸眼井壁支撑工艺，结合中国西北油田已完钻超深裸眼水平井井况，首先，提出了基于“铝合金+碳钢”的多材质复合管柱组合及设计方法；其次，开展了基于管柱实物屈曲实验数据的管柱临界屈曲载荷计算模型适用性评价，并优选出了适合于“铝合金+碳钢”多材质复合管柱的屈曲临界载荷计算模型；最后，研究了综合考虑管柱扭矩、摩阻、刚性、井眼条件、管柱强度及材质的多材质复合管柱下入性分析方法，并利用下入性分析软件对西北油田顺北X1井、X2井、X3井、X4井复合管柱进行了下入可行性评价。该方法在X1井和X2井得到成功应用，进一步论证了该工艺现场应用的可行性。研究成果可为超深水平井裸眼井壁支撑的复合管柱设计和下入可行性评价提供理论参考。     

超高功率超短脉冲发展的现状及相关科学问题

超高功率超短脉冲激光系统在其聚焦焦点附近可以实现高达1022-24 W/cm2的峰值功率输出,为强场物理实验研究,以及实验室内模拟极端环境下的天体物理条件提供了直接的实现方案.自从国际上首次提出了建造EW激光的概念,即输出总功率达到1018 W的大型激光系统后,国际上很多国家都在设计和建造大规模的超高功率超短脉冲激光系统.本文简要介绍了国际上这种规模激光系统的发展状况,并结合国内超高功率高能超短脉冲激光的发展,对超高功率超短脉冲激光系统发展中相关技术问题进行阐述.     

高陡横坡段桩柱式桥梁双桩基础受力分析

基于高陡横坡段桩柱式桥梁双桩基础承载特性,提出了一种改进有限杆单元计算分析方法.分析了高陡横坡段桩柱式桥梁双桩基础承载机理及受力特性,建立了双桩基础计算分析模型.其次,根据前、后桩与边坡相对位置关系,给出了后桩所受剩余下滑力与前桩所受土压力的比例关系.在传统有限杆单元分析方法基础上,结合陡坡桩受力特征,导得了考虑桩土共同作用与"P-Δ"效应的单元刚度矩阵修正方法,并在此基础上编制了适用于高陡横坡段桩柱式桥梁双桩基础的有限杆单元分析MATLAB计算程序.采用室内模型试验对本文计算方法进行验证,给出了适用于陡坡段桥梁桩基的设计流程图.研究结果表明:本文理论计算值与模型试验实测结果吻合良好,表明本文计算方法正确可行,可为同类工程设计提供参考.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

基于修正斜压场的RC框架边节点剪切性能分析

为研究钢筋屈服强度和混凝土抗压强度对钢筋混凝土(RC)框架边节点剪切性能的影响规律,基于修正斜压场理论(MCFT),对某框架边节点的剪切应力-应变骨架曲线进行数值模拟,并与试验结果进行对比.在验证MCFT算法的精度后,研究钢筋屈服强度和混凝土抗压强度两个参数变化对RC框架边节点剪切应力-应变骨架曲线和峰值剪切应力的影响规律.结果表明:基于MCFT可以较好地模拟RC框架边节点的剪切应力-应变关系曲线; RC框架边节点的峰值剪切应力对混凝土抗压强度的变化更为敏感,但当试件的钢筋(HRB400)屈服应力下降幅度超过16.45%时,对钢筋屈服应力的变化更为敏感;当试件的钢筋(HRB400)屈服应力下降幅度超过10%时,节点发生钢筋滑移破坏,此时峰值剪切应力会大幅下降.     

激光快速成型TC4合金显微组织及力学性能

采用金相显微镜、扫描电镜、电子拉伸机等，研究了激光快速成型TC4合金沉积态在平行沉积方向和垂直沉积方向的组织和力学性能.结果表明:激光快速成型TC4合金沉积态宏观组织沿沉积方向生长的粗大β柱状晶呈明暗相间的条带状结构，具备典型的魏氏组织特征;垂直沉积方向的强度比平行沉积方向的强度高，但塑性低;合金断口为韧窝状断口，垂直沉积方向的断口韧窝尺寸比平行沉积方向的小.     

三维打印器件后处理液研究

分析了不同的填充强化剂(后处理A液)、不同的后处理B液基料、后处理B液中水性环氧乳液的掺量及后处理液浸泡时间对石膏基打印器件耐水性、抗压强度、尺寸偏差、表面微观结构的影响.结果表明:经纳米硅超硬固化剂处理后的打印器件抗压强度大幅提高,纳米硅超硬固化剂最适宜作为后处理A液;水性聚氨酯乳液PU-202B最适宜作为后处理B液的基料;后处理B液中加入水性环氧乳液,处理后打印器件的抗压强度增加、吸水率降低,但水性环氧乳液含量增加到一定程度后会出现尺寸偏差;后处理A、B液最佳浸泡时间分别为130 s和35 s;先浸泡后处理A液、后浸泡后处理B液的打印器件具有抗压强度高、吸水率小、表面较光滑、不脱粉等优良性能.     

运用试验设计法优化某军品压铸弹尾工艺

根据某军品部件出现的问题，应用试验设计法成功地找出了最优组合，提高了该部件的强度，解决了该强度问题，使生产得以正常进行。     

高性能称重配料系统控制策略的研究及实现

着重针对应用于饲料生产工艺的称重配料系统的控制策略进行研究,特别是对空中落差的研究,推出了实现该控制策略的高性能称重配料控制器,并进行切实可行的软硬件设计,以真正实现称重配料系统的高性能。