Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

海上电泵结蜡井热循环洗井工艺参数优化设计

为探索海上油田电泵举升结蜡井热循环洗井工艺井筒温度场分布规律，综合考虑潜油电机增温、电缆散热、热流体注入量、注入深度、注入温度、结蜡管段传热和海水空气导热的影响，基于热能守恒原理，建立了电泵井结蜡热循环洗井工艺井筒温度场计算模型，分析了热流体注入温度和注入量对混合产出流体的井筒温度分布的影响。研究结果表明，随着注入量的增加混合产出液沿程井筒温度增加，随着注入温度的增加混合产出液沿程井筒温度增加。该方法可有效指导现场措施工艺的实施，达到延长结蜡井的清蜡周期、延缓产液/产油量下降速度的目的。     

改进蚱蜢算法在电动汽车充换电站调度中的应用

电动汽车充换电站调度优化问题一般采用群智能优化算法求解，但现有算法存在陷入局部最优、早熟收敛等缺陷，因此提出一种改进的蚱蜢算法:采用边界反弹机制，提高算法效率;引入正余弦搜索机制，加强算法的全局搜索能力;采用Lévy飞行对粒子进行随机扰动，防止种群陷入局部最优;采用非线性收敛策略加快算法后期的收敛速度.实验结果表明，该算法在电动汽车充换电站调度优化问题上，性能优于原始蚱蜢算法以及其他现有群智能算法.     

基于交通信号灯信息的混合动力汽车节能预测控制方法

针对传统混合动力汽车控制方法不考虑已知道路交通信号灯信息对车辆能量管理影响的问题,提出了基于交通信号灯信息的混合动力汽车节能预测控制智能优化策略。通过建立混合动力汽车系统的简化模型,并采用连续广义最小残量方法求解模型预测控制问题。运用MATLAB/Simulink进行仿真,仿真结果验证了交通信号灯信息模型的有效性,以及所设计的模型预测控制算法大幅度提高混合动力汽车的燃油经济性的能力和实时控制性能。研究结果表明所提出的控制策略可以实现车辆行驶轨迹的优化控制,显著提高了车辆的燃油经济性,并满足系统的实时最优控制要求。     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

NIPA类共聚温敏水凝胶中水的状态和耐热性

用N-异丙基丙烯酰胺（NIPA）与丙烯酸钠（SA）及甲基丙烯酸钠（SMA）共聚合成了两个系列的水凝胶，研究了共聚组成与水凝胶基本性质的关系，并用示差扫描量热法（DSC）和热失重法（TG）研究了此类水凝胶中水的状态和耐热性。     

APCI5000电气自动化成套装置设计

电气自动化成套装置种类繁多，并广泛应用于电力系统．结合现场实际商业运行期所积累的经验，并根据市场预测以及目前工控机发展动态，提出了采用APCI5000工业控制计算机实现电气自动化成套装置设计的最佳方案．     

电磁场中带电粒子束运动的力学模拟

研究以不同初速度进入互相垂直的匀强磁场和均强电场中的带电粒子束的运动情形，并同相似的力学运动相比拟，建立了直观的力学模型。     

电加热炉模糊变结构温度控制系统

本文针对炉体温度对象建模较难，常规算法难以发挥良好的作用，阐述了将模糊控制与变结构控制结合控制的原理及方法，并成功的将该设计方法应用于成都砂轮厂树脂硬化炉的温度控制中，取得良好效果。