螺栓连接大变形梁非线性振动特性的实验研究

柔性机械臂、大型可展开天线等机械结构的动作精度受运动过程中大变形几何非线性和连接处接触非线性的影响十分显著。以含螺栓连接结构的大变形梁作为研究对象，针对动力学建模和振动特性开展了实验研究，通过数值计算验证了实验发现的非线性振动特性。搭建了含螺栓连接柔性大变形梁的实验台架，开展了敲击和正弦激振的实验测试。实验结果表明，螺栓连接的柔性梁较连续梁的（无螺栓连接）模态频率降低，阻尼增加，反映出随着激励能量增大，模态频率降低的非线性模态特征。改变螺栓连接位置会显著影响结构的模态频率，其变化规律可由求解线性矩阵特征值定性反映。     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

多点柔性墩连续顶推技术在梁桥中的应用

结合工程施工实践,介绍了多点柔性墩连续顶推施工技术.     

结合梁剪力连接件剪拔受力的非线性分析

探讨了结合梁剪力连接件在复杂受力情况下的非线性分析模式与分析方法，计算结果与剪拔试验模型实测结果吻合良好。在此基础上，计算了广州内环中山一路结合梁剪力连接件的受力行为，为设计单位提供了设计参数。     

托梁换柱技术在某砖混结构住宅改造中的应用

介绍了某砖混结构的住宅在旧城区改造过程中,运用托梁换柱的技术,将底层外墙拆除,改建为商铺的设计、施工等情况.     

合金铸铁激光处理的探讨——Ⅱ.激光辐照工艺参数的控制

用热传导方程控制激光辐照温度,建立了一种新回归方程以控制激光辐照硬化深度,选用卡尔丹公式列热传导方程及同归方程联立求解,可得到同时满足一定的硬化深度及表面最高温度双重要求的工艺参数,此种方法可作为激光硬化处理工艺参数的控制或预报,对本合金铸铁的激光硬化处理,其表面温度的下限应大于其熔点温度,即以表面产生微熔的快速冷凝处理为宜,并以选取低功率慢扫描为最佳。     

梯形水平折梁的内力分析

本文对梯形水平折梁（０≤α＜∏２）和矩形水平折架（α＝∏２）用最小余能原理进行了内力分析，并导出了相应的计算公式，可在工程结构设计中采用     

钢-混凝土连续组合梁桥的理论分析和试验研究

根据完全剪力连接的连续组合梁桥的构造特点及各部分受力机理,做出合理假设,提出分层平面框架计算模型该计算模型用于沈阳市东西快速干道工程某段连续组合梁桥,计算值与静载试验实测值非常接近,证明了本计算模型用于钢-混凝土连续组合梁桥正确实用的.     

后张法预应力混凝土T梁静载试验

简要叙述了后张法T梁静载试验的方法，步骤，并通过一元线性回归分析对试验结果进行了验证。