轧制道次间插入冷却对特厚钢板组织与性能的影响

使用实验轧机旁冷却装置配合轧机进行轧制实验，研究轧制道次间不同冷却工艺对特厚钢板组织和性能的影响规律.研究结果表明:采用道次间冷却工艺可以在全厚度方向获得组织细化及强韧性提高效果，采用强冷道次间冷却实验钢1/4处晶粒尺寸可细化至10μm，强度为376MPa，-40℃冲击功为169J;心部晶粒尺寸可细化至15μm，强度为360MPa，-40℃冲击功为123J.本工艺可形成470μm厚表层细晶层，晶粒尺寸可细化至5μm;粗轧道次间插入冷却工艺轧制钢板强度和冲击韧性优于中间坯冷却工艺;随冷却强度增加，钢板内部组织明显细化且强度大幅提高.     

地理国情普查地表覆盖内业解译的质量问题研究

地表覆盖内业解译是地理国情普查的一道重要工序。地理国情地表覆盖内业解译现存图斑平面位置精度不足、分类错误多种多样等普遍问题,问题突出典型。文中针对这些问题图文并茂、清晰明了的进行了说明,并从多方面分析问题产生的原因,提出加强对技术指标和采集原则的学习和理解,加强内业与外业的结合,充分发挥解译样本的作用等建议,以有效提高内业解译的质量。     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

激光快速成型TC4合金显微组织及力学性能

采用金相显微镜、扫描电镜、电子拉伸机等，研究了激光快速成型TC4合金沉积态在平行沉积方向和垂直沉积方向的组织和力学性能.结果表明:激光快速成型TC4合金沉积态宏观组织沿沉积方向生长的粗大β柱状晶呈明暗相间的条带状结构，具备典型的魏氏组织特征;垂直沉积方向的强度比平行沉积方向的强度高，但塑性低;合金断口为韧窝状断口，垂直沉积方向的断口韧窝尺寸比平行沉积方向的小.     

凋亡抑制蛋白与肿瘤关系的研究

凋亡抑制蛋白(inhibitor of apoptosis proteins,IAPs)可以作为癌症诊断和治疗的靶点,在肿瘤研究方面备受关注,就凋亡抑制蛋白的结构、功能、在肿瘤中的表达与肿瘤的关系等研究进展作一综述,为凋亡抑制蛋白的研究提供信息和思路.     

高温作用后砂岩物理力学性质阈值温度的确定——基于机器学习算法

通过采用机器学习算法，提出了高温作用后砂岩物理力学性质变化的阈值温度的确定方法。基于Python语言，利用K-Means、SVM算法，实现了对样本数据的分类和聚类，确定了阈值温度区间，验证了二分类法的合理性和准确性.结果表明，砂岩样本的阈值温度区间为400~600 ℃，阈值温度上下砂岩的物理力学性质存在显著差异，体现为阈值温度区间以下的岩样物理力学性质较为分散，而阈值温度区间以上的岩样物理力学性质较为集中.     

温度和机械载荷联合作用下油田超深井中硬质涂层膨胀锥与套管的屈服挤毁压强及试验验证

在充分考虑温度载荷、机械载荷、硬质涂层膨胀锥硬度、套管硬度对膨胀锥与套管之间屈服挤毁压强影响的基础上,根据分形理论和接触力学推导出膨胀锥与套管之间屈服挤毁压强的计算公式.数值分析表明:膨胀锥与套管之间的屈服挤毁压强随最终温度、分形粗糙度、线膨胀系数、硬质涂层膨胀锥布氏硬度、中间主应力系数、套管壁厚的增大而增大;当分形维数从1增大时,膨胀锥与套管之间的屈服挤毁压强随分形维数的增大而减小;当分形维数增大到接近于2时,膨胀锥与套管之间的屈服挤毁压强随分形维数的增大而增大;随拉压强度比的增大,膨胀锥与套管之间的屈服挤毁压强减小.屈服挤毁压强的计算值与试验测试值之间的相对误差为-8.9253%～-0.9901%.     

冷轧带钢局部高点卷取过程起筋控制的建模与仿真

为了研究带钢局部高点卷取起筋的控制方法，利用三维弹塑性变形基本理论，并引入带钢塑性流动因子，建立了弹塑性卷取应力和起筋量模型.基于应力函数假设、S. Timoshenko最小功原理和伽辽金虚位移法建立了起筋带钢的应力场分布和可用于在线计算的起筋临界卷取张力设定模型.仿真结果表明：局部高点在径向累积叠加所引起的带钢张力不均匀分布和轴向压应力是导致带钢起筋的主要原因；起筋量随局部高点高度、卷径和卷取张力增加而增大，薄带钢比厚带钢起筋量增幅明显；临界卷取张力随卷径、带钢厚度和局部高点高度增大而减小.     

喷射共沉积6066Al/SiCp复合材料热处理塑性变化机理分析

研究了T6热处理对6066Al/SiCp复合材料材料力学性能的影响,结果表明,复合材料经530℃固溶1 h后,170℃时效8 h达到峰时效,其抗拉强度达418.6 MPa;复合材料延伸率随时效时间的增加不断降低.     

Pilot Study on Nanofiltration Combined with Ozonation and GAC for Advanced Drinking Water Treatment

IntroductionThe conventional process for surface water treatment,which consists of flocculation, sedimentation and filtrationcurrently, had been applied inproducingdrinkingwater formany years. Although this process can remove turbidityand bacteria in surface water effectively, only about from20% to 30% of natural organic matter ( NOM) can beeliminated. When the purified water is disinfected bychlorination, these NOMs may react with chlorine. As aresult some dis…