微积分一种重要类型极限的计算方法

给出了一种类型函数极限运算的公式及其在微积分极限计算中的具体应用,应用此极限公式可以求某些极限运算中参数的值,给出一元函数在某一点连续的充分条件和求一个曲线的渐近线,同时提供了一个命题的证明方法.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

Polarized Emission of Molecular Film With Lanthanide (Ⅲ) Complex

1 Results In the coordination system by using complexation with organic ligand, the ff emission of lanthanide(Ⅲ) (Ln(Ⅲ)) is induced the excitation energy transfer form the organic chromophore under the light-irradiation. However, there are not so much number of reports to discuss the energy relaxation mechanism in such complexes with Ln(Ⅲ). Recently, we succeeded firstly to estimate the rate constant of the energy transfer between the ligand and Ln(Ⅲ) in Pr(Ⅲ)-phenanthroline analogs[1]. Here, we will di...     

合金铸铁激光处理的探讨——Ⅱ.激光辐照工艺参数的控制

用热传导方程控制激光辐照温度,建立了一种新回归方程以控制激光辐照硬化深度,选用卡尔丹公式列热传导方程及同归方程联立求解,可得到同时满足一定的硬化深度及表面最高温度双重要求的工艺参数,此种方法可作为激光硬化处理工艺参数的控制或预报,对本合金铸铁的激光硬化处理,其表面温度的下限应大于其熔点温度,即以表面产生微熔的快速冷凝处理为宜,并以选取低功率慢扫描为最佳。     

对摩擦力作功与摩擦生热的量度的认识

本文通过对摩擦力作功与不擦生热的讨论，给出摩擦生热的量度方法．     

血液的光学性质研究

本文用辐射输运理论方法去计算红细胞的光学特征量,并在此基础上提出检测血细胞数密度的理论实验方案,其结果与传统的方法一致。本文为开发一种血球数自动检测仪提供了理论基础和仪器结构原型。     

关于极限的几个定理

给出了极限的几个定理及其推论，可以解决或简化某类极限问题。推论2修正了数学通报11（1963）《关于极限的一个定理》。     

化工传热过程计算方法的分析

通过分析比较化工传热过程计算中的平均温度差法(MTD法)和传热单元数法(NTU法),找出了它们之间的内在联系,结合这两种方法的优点,组合成了一种新的计算方法,应用于化工传热过程的计算,可使计算过程大为简便,同时又可评价换热设备流动型式的合理性。