财政性科技经费监管体系探析

我国初步建立了财政性科技经费监管体系,但是在监督主体、监督制度等方面还存在缺陷,科技经费监督出现诸多问题。建立要加强宏观层面的统筹规划,建立由政府、承担单位和外部主体上下联动、横向联合的立体监督体系。     

仿生非光滑花纹沟对轮胎抗滑水性能的影响

以205/55R16乘用车轮胎为研究对象,采用计算流体动力学建立了考虑胎面花纹变形的轮胎滑水分析模型;以气-液二相流数值模型分析了轮胎的滑水性能,并将临界滑水速度仿真值与NASA滑水速度预测值及轮胎发生滑水时力平衡下的速度进行对比.在此基础上,引入仿生减阻理念,研究了夹角为60°、高度为0.6mm的仿生对称V形结构对花纹沟排水量和水流阻力的影响,并将其结构特征信息等效移植到接地区轮胎花纹沟底,进行了仿生花纹轮胎的滑水性能分析.结果表明:所建滑水分析模型可用来分析轮胎滑水时的流体运动特性;相对原花纹轮胎,仿生非光滑花纹沟轮胎通过提高接地区花纹沟内水流速度,降低了胎面动水压力,提高了临界滑水速度.     

利用SRTM数据修测高山区地貌的探讨

在高海拔区域测制地形图,如青藏高原地区,所获取的遥感影像局部存在着大范围的高山阴影或云雪覆盖,造成立体观测地貌困难的现象,探讨应用SRTM数据对这类特殊区域地貌进行修测补绘。介绍了数据处理的作业过程,并对实验区SRTM与SPOT5影像立体测图成果进行实验对比分析,成果符合要求。     

“二三结合”开发模式渗流特征研究

L油田B区块开展"二三结合"实验区,"二三结合"开发模式渗流特征对区块的合理高效开发具有重要意义。为了明确其渗流特征,利用油藏数值模拟软件Eclipse建立代表意义的油藏数值模型,研究区块"二三结合"开发模式下原射孔层和补孔层的渗流特征,分析了"二三结合"开发模式下,不同开发阶段综合含水率、采出程度、井底压力、地层压力及含水饱和度的变化特征。研究表明,"二三结合"开发模式先通过水驱开发挖潜原射孔层剩余油,提高厚油层顶部剩余油的采出程度,再通过聚合物驱进一步提高开发效果,通过水驱与聚驱的综合作用,最终得到较好的开发效果。     

Effects of Strain Rate,Temperature and Grain Size on the Mechanical Properties and Microstructure Evolutions of Polycrystalline Nickel Nanowires: A Molecular Dynamics Simulation

Through molecular dynamics(MD)simulation,the dependencies of temperature,grain size and strain rate on the mechanical properties were studied.The simulation results demonstrated that the strain rate from 0.05 to 2 ns~(–1 )affected the Young’s modulus of nickel nanowires slightly,whereas the yield stress increased.The Young’s modulus decreased approximately linearly;however,the yield stress firstly increased and subsequently dropped as the temperature increased.The Young’s modulus and yield stress increased as the mean grain size increased from 2.66 to6.72 nm.Moreover,certain efforts have been made in the microstructure evolution with mechanical properties association under uniaxial tension.Certain phenomena such as the formation of twin structures,which were found in nanowires with larger grain size at higher strain rate and lower temperature,as well as the movement of grain boundaries and dislocation,were detected and discussed in detail.The results demonstrated that the plastic deformation was mainly accommodated by the motion of grain boundaries for smaller grain size.However,for larger grain size,the formations of stacking faults and twins were the main mechanisms of plastic deformation in the polycrystalline nickel nanowire.     

广西高技术产业科技创新能力评价研究

文章在分析广西高技术产业发展现状基础上,构建高技术产业科技创新能力评价指标体系,运用熵值法,基于2015—2019年面板数据对广西高技术产业的创新能力进行实证研究.研究表明:广西高技术产业创新能力在西部五省中处于较低水平;广西高技术创新产出实力略低于创新投入实力,创新技术吸收实力仍相对较弱;广西高技术四大行业创新能力存在差异,即电子及通信设备制造产业科技创新投入和产出效果最好,医药制造业和电子通信及装备制造业创新投入高,创新产出评分偏低,医疗仪器设备及仪器仪表制造产业和计算机及办公设备制造产业创新吸收能力很弱.基于以上结论,文章从加大创新资源投入、推动创新平台建设、加强人才队伍建设等方面提出了对策建议.     

具有Logistic增长项的两种群竞争Keller-Segel模型的稳定性分析

应用线性化方法研究两种群竞争的Keller-Segel模型常数平衡解的个数及其稳定性问题.     

Predicting Initial Formation Temperature for Deep Well Engineering with a New Method

With the progress of science and technology, human beings explore the energy under-ground with thousands of meters. As a thermophysical parameter, initial formation temperature (IFT) plays an essential...     

三维打印器件后处理液研究

分析了不同的填充强化剂(后处理A液)、不同的后处理B液基料、后处理B液中水性环氧乳液的掺量及后处理液浸泡时间对石膏基打印器件耐水性、抗压强度、尺寸偏差、表面微观结构的影响.结果表明:经纳米硅超硬固化剂处理后的打印器件抗压强度大幅提高,纳米硅超硬固化剂最适宜作为后处理A液;水性聚氨酯乳液PU-202B最适宜作为后处理B液的基料;后处理B液中加入水性环氧乳液,处理后打印器件的抗压强度增加、吸水率降低,但水性环氧乳液含量增加到一定程度后会出现尺寸偏差;后处理A、B液最佳浸泡时间分别为130 s和35 s;先浸泡后处理A液、后浸泡后处理B液的打印器件具有抗压强度高、吸水率小、表面较光滑、不脱粉等优良性能.     

A Forward Selection Method on Customer Credit

In this paper, we discuss a selection and evaluation method of customer credit for the commercial bank loans operation, and put forth a forward selection model by optimization techniques. At last, we also give an example to analyze its application.