位移放大型扭转阻尼器性能分析

为了加固梁柱节点、避免框架结构出现"弱节点"的破坏模式、提高框架结构整体的抗震和耗能能力,研制出一种具有自主知识产权的位移放大型扭转阻尼器(DATD),并对其进行数值分析和试验研究.首先,设计了18个具有不同参数的DATD,建立其有限元模型进行数值分析;随后,设计并制作了一个DATD,进行性能试验并与有限元分析结果对比.结果表明:DATD滞回曲线饱满,耗能能力强;有限元分析与性能试验的滞回曲线吻合较好,且随着加载位移的增加,两者间误差变小,因此可以采用建立的有限元模型来研究DATD的力学性能.最后,对DATD进行参数影响分析,研究了铅芯直径、铅芯距中轴距离、橡胶层直径、橡胶层厚度及橡胶剪切模量对其特征参数的影响,结果表明:DATD的屈服剪力、等效刚度、等效阻尼比及耗能系数随着铅芯直径增大而明显增大,随着铅芯距中轴距离的增大略有增大;随着橡胶层直径、橡胶剪切模量的增大,屈服剪力及等效刚度逐渐增大而耗能系数及等效阻尼比逐渐减小;4个特征参数均随着橡胶层厚度的增大而略微减小.     

Meet-Cloud for Secure and Accurate Distribution of Negative Messages in Vehicular Ad hoc Network

Keeping Vehicular Ad hoc Network(VANET) from attacks requires secure and efficient distribution of information about bad entities. Negative messages are pieces of information that define the negative attributes of vehicles. By formally defining the negative message, we observe that accuracy is essential for its efficient distribution. We formally define the coverage percentage and accurate coverage percentage to describe the availability and distribution efficiency of negative message. These two metrics can jointly evaluate the performance of a distribution method. To obtain both high coverage percentage and high accurate coverage percentage, we propose meet-cloud, a scheme based on meet-table and cloud computing to securely and accurately distribute negative messages in VANET. A meet-table in a Road Side Unit(RSU) records the vehicles it encounters. All meettables are sent to cloud service to aggregate a global meet-table. The algorithm for distributing and redistributing negative messages are designed. Security analysis shows that meet-cloud is secure against fake and holding on to negative message attacks. Simulations and analysis demonstrate that meet-cloud is secure under denial of service and fake meet-table attacks. The simulation results also justify that meet-cloud outperforms the RSU broadcast and epidemic model.     

超强筋小麦粉面包烘焙技术研究

为了烘焙出能充分表现超强筋小麦济麦229面粉品质特性的优良面包,设置了4种醒发时间处理、5种酵母和糖用量处理、4种配粉处理,对超强筋小麦面粉的面包品质进行了评价分析。结果表明,在4个醒发时间处理中,当面团醒发时间为30min和面包胚醒发时间为50min时,烘焙的面包品质最好。在5种酵母和糖用量的处理中,利用吐司面包程序时,干酵母和糖的用量分别为6g和24g时烘焙的面包品质最好；利用法式面包程序时,干酵母和糖的用量分别为3g和18g时烘焙的面包品质最好。在4个配粉处理中,200g超强筋小麦济麦229面粉中添加100g普通小麦济麦22面粉的混粉烘焙得到的面包品质最好。因此,适当调整超强筋小麦粉面包的面团、面包胚醒发时间及物料配比,可以烘焙出品质优良的面包。     

General mechanisms of drought response and their application in drought resistance improvement in plants

Plants often encounter unfavorable environmental conditions because of their sessile lifestyle. These adverse factors greatly affect the geographic distribution of plants, as well as their growth and productivity. Drought stress is one of the premier limitations to global agricultural production due to the complexity of the water-limiting environment and changing climate. Plants have evolved a series of mechanisms at the morphological, physiological, biochemical, cellular, and molecular levels to overcome water deficit or drought stress conditions. The drought resistance of plants can be divided into four basic types-drought avoidance, drought tolerance, drought escape, and drought recovery. Various drought-related traits, including root traits, leaf traits, osmotic adjustment capabilities, water potential, ABA content, and stability of the cell membrane, have been used as indicators to evaluate the drought resistance of plants. In the last decade, scientists have investigated the genetic and molecular mechanisms of drought resistance to enhance the drought resistance of various crops, and significant progress has been made with regard to drought avoidance and drought tolerance. With increasing knowledge to comprehensively decipher the complicated mechanisms of drought resistance in model plants, it still remains an enormous challenge to develop water-saving and drought-resistant crops to cope with the water shortage and increasing demand for food production in the future.     

A Layer-Stripping Method for 3D Near-Surface Velocity Model Building Using Seismic First-Arrival Times

In order to improve the efficiency of 3D near-surface velocity model building, we develop a layer-stripping method using seismic first-arrival times. The velocity model within a Common Mid-Point (CMP) ...     

An Economic Model-Based Matching Approach Between Buyers and Sellers Through a Broker in an Open E-Marketplace

A broker in an open e-marketplace enables buyers and sellers to do business with each other. Although a broker plays an important role in e-marketplaces, theory and guidelines for matching between buyers and sellers in multi-attribute exchanges are limited. Therefore, a challenge for a broker’s responsibility is how to maximize a buyer’s total satisfaction degree as its goals under the consideration of trade-off between a buyer’s buying quantity and price paid to a seller, and other attributes. To solve this challenge, this paper proposes an economic model-based matching approach between a buyer’s requirements and a seller’s offers. The major contributions of this paper are that (i) a broker can model a seller’s price policy as per a buyer’s buying quantity through communication between a broker and a seller; (ii) due to each buyer’s different quantity demand, a broker models a buyer’s satisfaction degree as per a buyer’s buying quantity based on communication between a broker and a buyer; and (iii) to carry out a broker’s matching processes, an objective function and a set of constraints are generated to help a broker to maximize a buyer’s total satisfaction degree. Experimental results demonstrate the good performance of the proposed approach.     

基于回转输运试验的煤散料离散元接触参数修正

为获取精确的刮板输送机离散元模拟结果，基于回转输运试验，通过响应面法对煤料的接触参数进行修正.采用Plackett-Burman试验考察接触参数对受力及堆积角的影响，发现煤-钢静摩擦系数、煤-煤摩擦系数具有显著正效应.根据爬坡试验结果，以受力及堆积角为响应值规划Box-Behnken试验，建立受力、堆积角与显著项间的二次回归多项式，以实测数据为目标值求得最佳参数:煤-钢静摩擦系数为0.401，煤-煤静摩擦系数为0.333，煤-煤滚动摩擦系数为0.041.通过不同输运条件下的回转试验验证了参数的准确性，为刮板输送机的离散元研究提供参考.     

Study on the Centralization Strategy of the Blood Allocation Among Different Departments within a Hospital

By far, the researches on how to distribute blood products among different departments in hospital have not been further studied, though the problem of blood shortage and wastage that caused by improper blood allocation is severe, which may endanger patient’s lives and impose considerable costs on hospitals. In order to solve this problem, this paper mainly studies on how to distribute the blood items among different departments within a hospital and investigates the allocation approach with the novel management method by centralizing the inventory of several different departments. By integrating the blood inventory requirements of some departments, the hospital could reduce the rate of blood shortage and wastage effectively, release the pressure of the occupancy of resources and reduce the bullwhip effect of blood products. This paper illustrates the centralization principle in hospital and formulates the mixed integer programming model to work out the optimal allocation network scheme and the optimal inventory setting for every department. And the results of the numerical example demonstrate that this centralization method could considerably reduce blood shortage and wastage in hospital by about 72% and 90% respectively. Furthermore, it could decrease the total cost by about 108,540 RMB a month on blood supply chain management in the hospital and improve the effect of some certain surgeries by transfusing the fresh blood to patients.     

Effects of Strain Rate,Temperature and Grain Size on the Mechanical Properties and Microstructure Evolutions of Polycrystalline Nickel Nanowires: A Molecular Dynamics Simulation

Through molecular dynamics(MD)simulation,the dependencies of temperature,grain size and strain rate on the mechanical properties were studied.The simulation results demonstrated that the strain rate from 0.05 to 2 ns~(–1 )affected the Young’s modulus of nickel nanowires slightly,whereas the yield stress increased.The Young’s modulus decreased approximately linearly;however,the yield stress firstly increased and subsequently dropped as the temperature increased.The Young’s modulus and yield stress increased as the mean grain size increased from 2.66 to6.72 nm.Moreover,certain efforts have been made in the microstructure evolution with mechanical properties association under uniaxial tension.Certain phenomena such as the formation of twin structures,which were found in nanowires with larger grain size at higher strain rate and lower temperature,as well as the movement of grain boundaries and dislocation,were detected and discussed in detail.The results demonstrated that the plastic deformation was mainly accommodated by the motion of grain boundaries for smaller grain size.However,for larger grain size,the formations of stacking faults and twins were the main mechanisms of plastic deformation in the polycrystalline nickel nanowire.     

Fuzzy Views on Black-Litterman Portfolio Selection Model

In this paper, views of investor are described in fuzzy sets, and two fuzzy Black-Litterman models are constructed with fuzzy views and fuzzy random views respectively. In the models, expected returns and uncertainty matrix of views are redefined and the views are formulated by fuzzy approaches suitably. Then the models are tested with data from Chinese financial markets. Empirical results show that the fuzzy random views model performs the best, and both the fuzzy models are better than the traditional ones, demonstrating that the fuzzy approaches can contain more information in the views and measure the uncertainty more correctly.