冷却速率和奥氏体化温度对40 Cr钢球化退火的影响

为探究奥氏体化温度和冷却速率对40Cr钢球化过程的影响,采用双相区球化退火研究了热轧态40Cr钢的球化退火行为和力学性能。奥氏体化温度从760℃提高到800℃,冷却速率从10℃·h-1上升到30℃·h-1,组织硬度随冷却速度呈V形变化,碳化物球化率随冷却速度变化正好与前者相反。奥氏体化温度为760℃,冷却速率为20℃·h-1所得到的球化组织球化率高,且碳化物细小,具有良好的冷成形性能,可大幅度缩短球化退火时间,显著提高生产效率。提出了球化退火过程中离异共析转变机制,控制好球化过程中奥氏体化温度、冷却速率及保温时间有利于离异共析转变的发生。     

硫含量对中碳非调质钢中硫化物及组织的影响

利用真空感应炉冶炼了不同硫含量的中碳非调质钢,研究了S含量对非调质钢中硫化物形态分布及显微组织的影响.结果表明：在0.025%~0.065%范围内,随S质量分数的增加,非调质钢中硫化物的数量增多,偏聚分布现象加重;晶内铁素体比例随之升高,组织得到细化.通过热力学计算及相图信息研究了硫化物的类型转变. S含量增加时第Ⅲ类MnS在凝固末期以离异共晶形式较早析出,剩余液相中的S在凝固结束时以共晶形式析出为第Ⅱ类MnS.单独MnS以及MnS- V( C, N)复合硫化物均可作为晶内铁素体的有效形核核心,促进铁素体的生成.     

不锈钢水下激光焊接焊缝成形与力学性能

摘要： 采用水下局部干法激光焊接技术对1 mm厚SUS304不锈钢进行了焊接试验,重点分析了水深及保护气体流量对焊缝成形与力学性能的影响.实验结果表明：通过适当的水深与保护气体流量匹配,可以获得成形良好、剪切拉伸强度与母材相当的焊缝.在水深一定时,随着气体流量的增加,焊缝熔宽变宽,熔深变浅,深宽比减小.在气体流量一定时,随着水深的增加,焊缝熔深和熔宽也表现出类似的变化规律.与普通激光焊接相比,水下激光焊接改变了焊缝的散热方向以及散热速度,因此同一焊接工艺参数下,水下激光焊接的熔深变浅,熔宽变宽.
关键词： 水下焊接; 激光焊; 奥氏体不锈钢; 焊缝成形; 力学性能
中图分类号： TG 456.7文献标志码： A     

恒电位脉冲法检测高纯铁素体不锈钢的敏化

用恒电位脉冲（ＰＰＴ）法对高纯铁素体不锈钢的敏化度进行了检测，并与传统的动电位再活化（ＥＰＲ）法进行了比较，结果表明：ＰＰＴ法可以用来检测铁素体不锈钢的敏化，并且具有检测速度快，表面损伤小的优点     

改变Cr、Ni配比电弧炉冶炼超低碳不锈钢HoCr19Ni12Mo2

冶炼超低碳不锈钢因含碳极低（Ｃ≤０．０３０％）而使冶炼难度相当大，本文以ＨｏｏＣｒ１９Ｎｉ１２Ｍｏ２为例论述了通过调氧化前Ｃｒ、Ｎｉ的配比来降低氧化终点温度，从而降低冶炼难度     

60CrMnMo钢中稀土夹杂物生成的热力学分析

叙述了钢中稀土夹杂物生成的热力学分析方法．以６０ＣｒＭｎＭｏ用为例讨论了稀土夹杂物的热力学规律．并与实验结果作了比较．     

一起大型浓缩制碱锅炉早期泄漏事故分析

运用金相和扫描电镜，对运行仅三个月，材质为０Ｃｒｌ８Ｎｉ９不锈钢的浓缩制碱锅炉焊接热影响区出现的早期泄漏进行了分析，结果发现，在严重的晶间腐蚀基础上由于应力的作用，产生了严重的晶间型应力腐蚀开裂，导致了锅炉的早期泄漏。     

冷轧工艺对铁素体不锈钢成形性能的影响

为了研究冷轧工艺对新型铁素体不锈钢19Cr2Mo1W成形性能的影响,采用XRD,EBSD技术以及平均塑性应变比与粗糙度测量等手段,研究了不同压下率冷轧及随后退火过程中的织构演变和微观组织变化,并讨论了织构和微观组织对成形性能的影响.结果表明:随着冷轧压下率的增加,铁素体不锈钢中的α和γ纤维织构均有所增强,且α和γ纤维织构最终稳定取向分别为223〈110〉和111〈011〉.冷轧板α纤维织构中223〈110〉组分越强,退火后γ再结晶织构强度越高.冷轧板在1050℃退火时,薄板的γ再结晶织构强度高,再结晶组织均匀且尺寸较小,表面粗糙度最小,综合成形性能最佳.     

Effect of high anodic polarization on the passive layer properties of superduplex stainless steel friction stir welds at different chloride electrolyte pH values and temperatures

The conditions used for friction stir welding of duplex stainless steels determine the resulting mechanical and corrosion performance of the material.This study investigates the corrosion resistance of UNS S32750 and S32760 superduplex stainless steels(SDSSs)joined by friction stir welding,employing cyclic polarization,Mott–Schottky,and microscopy techniques for analysis.The microscopy images indicated the presence of a deleterious intermetallic phase after electrolytic etching of S32760,as well as decreased corrosion resistance.The presence of molybdenum in the steels promoted better passive behavior at low pH.The Mott–Schottky curves revealed p-n heterojunction behavior of the passive oxide.Images acquired after the polarization test by scanning electron microscopy showed higher passivation propensity with increases of temperature and pH.     

Effect of superplastic deformation on precipitation behavior of sigma phase in 3207 duplex stainless steel

Owing to excellent strength, toughness and corrosion resistance, duplex stainless steels(DSS) are widely used in constructional and petrochemical applications. Sigma phase, which has detrimental impact on the properties, is readily precipitated during hot working of DSS. However, precipitation behavior of sigma phase during superplastic deformation, which is the most significant processing method of DSS, is still unclear. In the current study,the effect of superplastic deformation on the precipitation behavior of sigma phase was investigated in 3207 duplex stainless steel. The result shows that superplastic deformation could prevent sigma phase precipitation generally by increasing mobility of grain boundaries and decreasing misorientation of the sigma phase boundaries, resulting in some sigma phase precipitated on the twin boundaries. Most of the sigma phase precipitated on ferrite-austenite interface with misorientation of 20–25°, while it precipitated in ferrite or austenite with the misorientation of 40°–45°. The orientation relationship between sigma phase and matrix matched well in austenite and on the ferrite/austenite interfaces, while it showed a small misfit in ferrite. The prevention effect of the superplastic deformation on the sigma phase precipitation was beneficial to quasi stable deformation stage,resulting in longer elongation.