不锈钢水下激光焊接焊缝成形与力学性能

摘要： 采用水下局部干法激光焊接技术对1 mm厚SUS304不锈钢进行了焊接试验,重点分析了水深及保护气体流量对焊缝成形与力学性能的影响.实验结果表明：通过适当的水深与保护气体流量匹配,可以获得成形良好、剪切拉伸强度与母材相当的焊缝.在水深一定时,随着气体流量的增加,焊缝熔宽变宽,熔深变浅,深宽比减小.在气体流量一定时,随着水深的增加,焊缝熔深和熔宽也表现出类似的变化规律.与普通激光焊接相比,水下激光焊接改变了焊缝的散热方向以及散热速度,因此同一焊接工艺参数下,水下激光焊接的熔深变浅,熔宽变宽.
关键词： 水下焊接; 激光焊; 奥氏体不锈钢; 焊缝成形; 力学性能
中图分类号： TG 456.7文献标志码： A     

恒电位脉冲法检测高纯铁素体不锈钢的敏化

用恒电位脉冲（ＰＰＴ）法对高纯铁素体不锈钢的敏化度进行了检测，并与传统的动电位再活化（ＥＰＲ）法进行了比较，结果表明：ＰＰＴ法可以用来检测铁素体不锈钢的敏化，并且具有检测速度快，表面损伤小的优点     

改变Cr、Ni配比电弧炉冶炼超低碳不锈钢HoCr19Ni12Mo2

冶炼超低碳不锈钢因含碳极低（Ｃ≤０．０３０％）而使冶炼难度相当大，本文以ＨｏｏＣｒ１９Ｎｉ１２Ｍｏ２为例论述了通过调氧化前Ｃｒ、Ｎｉ的配比来降低氧化终点温度，从而降低冶炼难度     

60CrMnMo钢中稀土夹杂物生成的热力学分析

叙述了钢中稀土夹杂物生成的热力学分析方法．以６０ＣｒＭｎＭｏ用为例讨论了稀土夹杂物的热力学规律．并与实验结果作了比较．     

一起大型浓缩制碱锅炉早期泄漏事故分析

运用金相和扫描电镜，对运行仅三个月，材质为０Ｃｒｌ８Ｎｉ９不锈钢的浓缩制碱锅炉焊接热影响区出现的早期泄漏进行了分析，结果发现，在严重的晶间腐蚀基础上由于应力的作用，产生了严重的晶间型应力腐蚀开裂，导致了锅炉的早期泄漏。     

冷轧工艺对铁素体不锈钢成形性能的影响

为了研究冷轧工艺对新型铁素体不锈钢19Cr2Mo1W成形性能的影响,采用XRD,EBSD技术以及平均塑性应变比与粗糙度测量等手段,研究了不同压下率冷轧及随后退火过程中的织构演变和微观组织变化,并讨论了织构和微观组织对成形性能的影响.结果表明:随着冷轧压下率的增加,铁素体不锈钢中的α和γ纤维织构均有所增强,且α和γ纤维织构最终稳定取向分别为223〈110〉和111〈011〉.冷轧板α纤维织构中223〈110〉组分越强,退火后γ再结晶织构强度越高.冷轧板在1050℃退火时,薄板的γ再结晶织构强度高,再结晶组织均匀且尺寸较小,表面粗糙度最小,综合成形性能最佳.     

Effect of high anodic polarization on the passive layer properties of superduplex stainless steel friction stir welds at different chloride electrolyte pH values and temperatures

The conditions used for friction stir welding of duplex stainless steels determine the resulting mechanical and corrosion performance of the material.This study investigates the corrosion resistance of UNS S32750 and S32760 superduplex stainless steels(SDSSs)joined by friction stir welding,employing cyclic polarization,Mott–Schottky,and microscopy techniques for analysis.The microscopy images indicated the presence of a deleterious intermetallic phase after electrolytic etching of S32760,as well as decreased corrosion resistance.The presence of molybdenum in the steels promoted better passive behavior at low pH.The Mott–Schottky curves revealed p-n heterojunction behavior of the passive oxide.Images acquired after the polarization test by scanning electron microscopy showed higher passivation propensity with increases of temperature and pH.     

Effect of superplastic deformation on precipitation behavior of sigma phase in 3207 duplex stainless steel

Owing to excellent strength, toughness and corrosion resistance, duplex stainless steels(DSS) are widely used in constructional and petrochemical applications. Sigma phase, which has detrimental impact on the properties, is readily precipitated during hot working of DSS. However, precipitation behavior of sigma phase during superplastic deformation, which is the most significant processing method of DSS, is still unclear. In the current study,the effect of superplastic deformation on the precipitation behavior of sigma phase was investigated in 3207 duplex stainless steel. The result shows that superplastic deformation could prevent sigma phase precipitation generally by increasing mobility of grain boundaries and decreasing misorientation of the sigma phase boundaries, resulting in some sigma phase precipitated on the twin boundaries. Most of the sigma phase precipitated on ferrite-austenite interface with misorientation of 20–25°, while it precipitated in ferrite or austenite with the misorientation of 40°–45°. The orientation relationship between sigma phase and matrix matched well in austenite and on the ferrite/austenite interfaces, while it showed a small misfit in ferrite. The prevention effect of the superplastic deformation on the sigma phase precipitation was beneficial to quasi stable deformation stage,resulting in longer elongation.     

超纯奥氏体不锈钢00Cr25Ni22Mo2N非敏化态晶间腐蚀与磷(硅)的晶界偏聚

运用金相、电子显微镜观察及表面分析技术,研究了超纯奥氏体不锈钢00Cr25Ni22Mo2N制造的汽提管在尿素生产环境下的腐蚀形态和机理。结果表明:该钢种在生产条件下产生非敏化态晶间腐蚀。其特征是腐蚀介质不仅沿晶界向钢的内部渗入,而且同时向晶界的两侧扩展,因而在管断面上观察到的晶间腐蚀路径较宽,但深度较浅并呈现漏斗形貌。电子显微镜观察、二次离子质谱、俄歇能谱分析及计算表明,这种材料晶界不贫铬、无第二相沉淀,但有磷(硅)的高度偏聚。晶界区磷的含量(约25％)比晶内高约三个数量级。作者认为,磷的晶界偏聚造成的与晶内在腐蚀电解质溶液中的电位差,是这种超纯奥氏体不锈钢非敏化态晶间腐蚀的原因。     

大气悬浮颗粒中一些微量金属元素的测定方法

应用硝酸十氢氟酸＋Ｈ＿２Ｏ＿２体系和高压密封罐技术消解大气悬浮颗粒物样品。并采用不锈钢缝管与火焰原子吸收相结合的分析方法，对样品中的Ｚｎ，Ｐｂ和Ｃｄ进行测定，提高灵敏度１．２～３．４倍。对Ｃｕ，Ｍｎ，Ｎｉ，Ｃｏ和Ｍｇ采用常规火焰原子吸收法进行测定。同时利用微量脉冲进样技术，使得样品消解后定容的体积由原来的５０ｍＬ减少到１０ｍＬ。从而在相同灵敏度条件下，使采样时间由１０ｈ缩短到２ｈ．该方法对各测定元素的相对标准偏差均小于７％，平均回收率为８５．９％～１０３．６％。