改进310奥氏体不锈钢长期时效后的组织与性能

借助扫描电子显微镜、透射电子显微镜以及高温、室温拉伸和硬度测试研究了实验室研发的改进310奥氏体不锈钢在700℃长期时效后的组织与性能.700℃时效1000 h后,实验钢在晶界和晶内析出了大量(Cr,Fe,Mo)23C6、(Cr,Fe)23C6、σ相和少量的χ相.析出相对实验钢的室温力学性能有明显的强化作用.强度增加,硬度升高20 Hv,同时延伸率仍保持在30%以上.高温下,析出强化效应减弱,延伸率轻微下降.通过断口表面和剖面观察发现,时效1000 h后,实验钢的高温拉伸断口为韧性断裂,未观察到裂纹和孔洞;而室温拉伸断口为脆性断裂,断口附近则观察到σ相中出现裂纹和孔洞.从σ相的脆-韧转变和实验钢基体的室温和高温强度的不同,讨论了在室温拉伸过程中产生裂纹和孔洞的原因,以及时效对室温和高温力学行为的不同影响.     

调质低碳贝氏体钢的组织和性能

研究了C--Mn--Mo--Cu--Nb--Ti--B系低碳微合金钢915℃淬火和490～640℃回火的调质工艺对钢的组织及力学性能的影响.用扫描电镜和透射电镜对实验钢的组织、析出物形态和分布以及断口形貌进行观察,采用X射线衍射仪分析钢中残余奥氏体的体积分数.结果表明:调质后,实验钢获得贝氏体、少量马氏体及残余奥氏体复相组织,贝氏体板条宽度只有250 nm,残余奥氏体的体积分数随着回火温度的升高而降低,经淬火与520℃回火后残余奥氏体的体积分数为2.1%.调质后析出物的数量激增,6～15 nm的析出物占70%以上.实验钢经过915℃淬火与520℃回火后,其屈服强度达到915 MPa,抗拉强度990 MPa,-40℃冲击功为95 J.细小的析出物及窄的板条提高了钢的强度.板条间有残余奥氏体存在,改善了实验钢的韧性.     

开轧温度对铌微合金化热成型钢氢致延迟开裂性能的影响

通过动态充氢恒载荷、氢渗透等实验研究轧制工艺对铌合金化热成型钢的氢致延迟开裂性能的影响。随着开轧温度从1000益降低到950益,热成型钢的氢扩散系数降低,氢致延迟开裂性能提高,耐腐蚀性能下降。透射电镜观察发现开轧温度为1000益时MX型析出相尺寸为30 nm;开轧温度为950益时热成型钢的MX型析出相尺寸为5 nm左右,可以观察到直径为50 nm Cr2 C3析出相。作为氢陷阱的纳米析出相是提高实验钢氢致延迟开裂性能的主要因素。析出相不同的原因是开轧温度为1000益时MX型析出相发生熟化现象,进一步抑制Cr2 C3的析出。     

高温注氢对钒合金微观结构的影响

研究了500℃高温条件下注氢对V-4Cr、V-4Ti和V-4Cr-4Ti三种合金微观结构的影响。在注氢实验之前,V-4Cr合金的基体清晰干净,而V-4Ti和V-4Cr-4Ti两种合金的基体中则出现很多相互平行和垂直的针状析出相,且大部分析出相周围都存在着位错。在500℃注氢实验之后,V-4Cr合金基体中出现大量的分布不均的黑色点状缺陷和缺陷簇,而V-4Ti和V-4Cr-4Ti两种合金的基体中除产生点状缺陷外,还出现高密度的气泡,且V-4Cr-4Ti合金中气泡的平均尺寸要稍小一些。另外,V-4Ti和V-4Cr-4Ti合金基体中原有的析出相在注氢实验之后都发生不同程度的溶解。在观察V-4Cr-4Ti合金基体中气泡分布规律时发现,在距离晶界25 nm的范围内几乎看不到气泡的存在,由此推断晶界的存在可以抑制氢气泡等辐照缺陷的产生。     

NbC纳米析出相对低合金高强钢氢致开裂的影响研究

We investigated the effect of nanosized NbC precipitates on hydrogen-induced cracking (HIC) of high-strength low-alloy steel by conducting slow-strain-rate tensile tests (SSRT) and performing continuous hydrogen charging and fracture analysis. The results reveal that the HIC resistance of Nb-bearing steel is obviously superior to that of Nb-free steel, with the fractured Nb-bearing steel in the SSRT exhibiting a smaller ratio of elongation reduction (I_δ). However, as the hydrogen traps induced by NbC precipitates approach hydrogen saturation, the effect of the precipitates on the HIC resistance attenuate. We speculate that the highly dispersed nanosized NbC precipitates act as irreversible hydrogen traps that hinder the accumulation of hydrogen at potential crack nucleation sites. In addition, much like Nb-free steel, the Nb-bearing steel exhibits both H-solution strengthening and the resistance to HIC.     

废水中氨氮沉淀物的结晶状态及其与捕收剂的作用机理

用实验室模拟废水和焦化废水研究了废水中其他成分对氨氮沉淀物结晶状态的影响.X射线衍射结果表明,模拟废水中生成的氨氮沉淀物是非晶态的,而焦化废水中的沉淀物是晶态的磷酸铵镁.红外光谱测试结果表明,pH值影响捕收剂十二酸钠或油酸钠与沉淀物的作用机理,pH=9时捕收剂在沉淀物表面发生物理吸附,而pH=11时发生化学吸附.模拟废水中氨氮沉淀物以油酸钠为捕收剂较好,而焦化废水中的氨氮沉淀物以十二酸钠为较好,其原因是沉淀物的结晶状态不同.     

TSCR流程生产钛微合金化高强耐候钢中的析出物

运用电子显微镜和化学相分析等多种实验手段研究了Ti微合金化高强耐候钢中的析出物,并在热力学计算的基础上分析了其析出过程. 结果表明:钢中主要存在TiC,TiCN,Ti4C2S2,TiN等析出物,连轧前TiN的析出过程已基本完成;大量纳米尺寸的TiC球形析出物粒子在铁素体的位错线上分布;Ti含量增加改变了MC相的粒度分布,小尺寸粒子的体积分数显著增加,增强了沉淀强化的效果.     

Effect of nano-sized precipitates on the crystallography of ferrite in high-strength strip steel

For strip steel with the thickness of 1.6 mm, the yield and tensile strengths as high as 760 and 850 MPa, respectively, were achieved using the compact strip production technology. Precipitates in the steel were characterized by scanning and transmission electron microscopy to elucidate the strengthening mechanism. In addition, intragranular misorientation, Kernel average misorientation, and stored energy were measured using electron backscatter diffraction for crystallographic analysis of ferrite grains containing precipitates and their neighbors without precipitates. It is found that precipitates in specimens primarily consist of TiC and Ti₄C₂S₂. Ferrite grains containing precipitates exhibit the high Taylor factor as well as the crystallographic orientations with {012}, {011}, {112}, or {221} plane parallel to the rolling plane. Compared with the intragranular orientation of adjoining grains, the intragranular misorientation of grains containing precipitates fluctuates more frequently and more mildly as a function of distance. Moreover, the precipitates can induce ferrite grains to store a relatively large amount of energy. These results suggest that a correlation exists between precipitation in ferrite grains and grain crystallographic properties.     

Effect of hot rolling on the microstructure and impact absorbed energy of the strip steel by CSP

The microstructures and impact absorbed energies at various temperatures were investigated for steel strips hot rolled to thickness reductions of 95.5%, 96.0%, 96.5%, 97.0%, and 97.5%. Results indicate that grain refinement can be realized with an increase in hot rolling reduction. Besides, finer precipitates can be achieved with an increase in hot rolling reduction from 95.5% to 97.0%. The impact absorbed energy decreases with a decrease in testing temperature for steel strips hot rolled to 95.5%, 96.0%, and 96.5% reductions in thickness. However, in the case of steel strips hot rolled to 97.0% and 97.5% reductions in thickness, the impact absorbed energy remained almost constant with a decrease in testing temperature.     

合金元素对R5系泊链钢中平衡析出相的影响

采用Thermo-Calc热力学计算软件,对R5系泊链钢在400～1600℃存在的平衡析出相进行了热力学计算,并讨论了合金元素对平衡析出相的影响. 结果表明,R5系泊链钢中平衡析出相主要为M_(23)C_6、M_6C、MX和AlN,其中M为Cr、Fe、Mn、Mo、Nb、Ni和V等,X为C、N和空位Va等. 在此基础上讨论了合金元素C、Cr、Mo和Nb对M_(23)C_6相、M_6C相及MX相的平衡摩尔含量和平衡析出温度的影响,优化了新型R5系泊链钢的合金体系及热处理工艺,提出新型R5系泊链钢的最佳热处理工艺为920±30℃淬火和600±30℃回火,其中金属元素Mo的质量分数以0.45%为佳.