试论铁塔制造行业中的外包管理

文章根据对现有的一些铁塔制造企业的实际加工情况和电力建设中所需的铁塔量的分析,提出对铁塔产品进行外包,并探讨对外包管理的控制。     

超细Fe(OH)_2悬浮液氧化反应中氧传递速率

基于膜理论,分析了含有超细Fe(OH)_2颗粒的淤浆中氧气的传递速率。利用数值解与近似解法给出了增强因子与反应-扩散模数间的关系,两者符合很好。实验验证了Fe(OH)_2的氧化速率与其粒径成反比。     

面向对象技术在管理信息系统（MIS）中的应用研究

本文分析了现行管理信息系统缺点，给出了一个通用管理信息系统实例，研究了面向对象技术在管理信息系统中的应用。     

马脾铁蛋白铁核表层磷铁组成稳定性

马脾铁蛋白络合Ｆｅ２＋的能力与它的铁核表层磷酸盐和Ｆｅ３＋组成含量有关．ＯＨ－参与铁核表层组成，并迫使铁蛋白释放Ｆｅ３＋．用强还原剂还原铁核表层时，铁蛋白只能释放磷酸盐．在Ｆｅ２＋、磷酸盐和氧化剂存在下，铁蛋白能贮存原铁核总磷酸盐量的６０％的磷．     

磺化四(1,4-二噻英)四氮杂卟啉铁的合成及初步表征

用氯磺酸作磺化剂,在四（1,4-二噻英）四氮杂卟啉铁配合物外围功能基对-二噻英环上发生直接取代反应,合成了水溶性良好的多取代磺化（1,4-二噻英）四氮杂卟啉铁配合物（简写为FeSPz（dtn）4）.并对磺化产物进行UV-Vis,IR,1HNMR和XPS等结构表征.     

COD与Fe0对硫酸盐还原菌还原作用的影响

采用间歇实验方法，分别在不同底物浓度下，分析了影响硫酸盐还原的机理，并考察了加入Fe^0对反应体系的强化作用．结果表明，底物浓度不足会减缓反应速度并降低最终反应结果，但对其反应延迟期没有影响．Fe^0对酶活性有调节作用，可以减小底物浓度变化对反应速度的影响，提高对底物的利用率．体系最终pH值随c（COD）／c（SO4^2-）增大逐渐提高，当c（COD）／c（SO4^2-）达到一定值后，最终pH值基本维持恒定．在相同底物浓度下，单质铁强化体系的最终pH值略高于空白体系．空白和单质铁强化两种体系的适宜c（COD）／c（SO4^2-）分别在5．1～6．9和3．9—5．1之间．在相同处理能力下，单质铁强化体系所需底物浓度是空白体系的75％．     

氧化铁/活性炭复合吸附材料去除水中砷的研究

以实验室制备的氧化铁、经硝酸和草酸铁改性的活性炭12×40(AC 1)为原料,分别制成两种氧化铁/活性炭复合吸附材料(FeO/AC-H和AC/Fe2(C2O4)).通过X射线衍射仪、氮气吸附仪、扫描电子显微镜和X射线光谱仪进行吸附的表观特性和物化性能分析,结果表明,活性炭的表面物质有磁铁矿(Fe3O4)、磁赤铁矿(γ-Fe2O3)、赤铁矿(α-Fe2O3)和针铁矿(α-FeO(OH)),而且这些物质的存在对活性炭的比表面积影响不大.采用静态吸附实验方法,用AC 1,FeO/AC-H和AC/Fe2(C2O4)三种吸附剂吸附去除水中砷,获得了吸附等温平衡数据,用Langmuir模型和Fre-undlich模型进行回归分析.结果表明,FeO/AC-H和AC 1对As(Ⅴ)的吸附更符合Langmuir吸附模型,而复合吸附剂AC/Fe2(C2O4)对As(Ⅴ)的吸附比较符合Freundlich吸附模型.     

磷、铁营养盐的协同交互作用对赤潮隐藻(Crytomonas sp.)生长增殖的影响

通过设计磷、铁双因子六水平二重复的随机试验,初步探讨了协同交互作用对赤潮隐藻生长增殖的影响.结果表明,磷、铁交互作用(P×Fe)极显著,隐藻合适生长铁浓度范围为50 n mol/L~1μmol/L,隐藻生长的培养液最优组合为50μmol/L磷×50 nmol/L铁浓度和10μmol/L磷×1 000 nmol/L铁.     

Effect of Starch Sources on the Release Rates of Herbicides Encapsulated

The effects of starch sources on the behaviors of starch matrices and on the rates of herbicides released from the matrices were studied for slow release. The starches considered include native corn starch, wheat starch, potato starch and cassava starch. The matrices were prepared through encapsulating 2,4-dichlorophenoxyacetic or 2,4,5 trichlorophenoxyacetic acids as model herbicides with hot-gelatinized starch pastes. The encapsulation was evaluated in terms of herbicide content, swellability, encapsulation efficiency, and release rate. The results show that starch sources play an important role on the matrix behaviors and on release rates. The rate of 2,4-D released follows the order： wheat starch 〈 potaot starch 〈 corn starch 〈 cassava starch. And for the rate of 2,4,5-T, this order is nearly the same only with an exception that the late two kinds of starch are similar. It is also demonstrated that herbicides with different water solubility show different release rates, no matter what type of starch is used as the matrices.     

Fabrication of plain carbon steel/high chromium white cast iron bimetal by a liquid-solid composite casting process

High-chromium white cast iron (HCWCI) is one of the most widely used engineering materials in the mining and cement indus-tries. However, in some components, such as the pulverizer plates of ash mills, the poor machinability of HCWCI creates difficulties. The bimetal casting technique is a suitable method for improving the machinability of HCWCI by joining an easily machined layer of plain car-bon steel (PCS) to its hard part. In this study, the possibility of PCS/HCWCI bimetal casting was investigated using sand casting. The inves-tigation was conducted by optical and electron microscopy and non-destructive, impact toughness, and tensile tests. The hardness and chemical composition profiles on both sides of the interface were plotted in this study. The results indicated that a conventional and low-cost casting technique could be a reliable method for producing PCS/HCWCI bimetal. The interfacial microstructure comprised two distinct lay-ers:a very fine, partially spheroidized pearlite layer and a coarse full pearlite layer. Moreover, characterization of the microstructure revealed that the interface was free of defects.