降温过程对Au24Cu19合金团簇结构变化影响

采用基于嵌入原子法的正则系综NVT分子动力学方法在原子尺度上计算了包含24个金原子和19个铜原子的Au24Cu19双金属团簇在急冷和连续降温过程中的结构演化.根据原子平均势能、主要原子键对数目以及原子堆积结构随温度的变化表明，随着温度的降低，团簇表现为铜原子在内，金原子和少量铜原子包覆在外的构型.在温度被降低到较高温度区间时，急冷降温过程中，键对数目呈高-低振荡变化；连续冷却过程中，键对数目则呈低-高振荡变化.在温度较低的区间，直至400K，这两个冷却条件下的键对数目表现为同步变化.     

外加入第二相颗粒对钢铁材料组织性能的影响

综述了外加颗粒对钢铁材料组织性能的影响,对钢铁中第二相颗粒的内部析出法和外部加入法的差异进行了简单概述。分析了第二相颗粒对钢铁材料的积极作用及不利影响,概述了钢铁材料中外加颗粒的选取原则、尺寸控制、加入量和加入方法等,提出了今后的研究方向。     

浅析金属屋面施工技术

金属屋面系统适用于大跨公共建筑。对工程实例铝镁锰合金板直立锁边屋面系统进行了详细介绍,阐述了屋面系统的构造、建筑技术要求的适应性、施工技术及质量控制等重点内容,为同类工程的设计提供了参考和借鉴。     

MgCl_2-KCl-AlF_3-(La_2O_3)熔盐体系电解制备Al-Mg-La中间合金

在质量比为41.5∶48.5∶10的MgCl_2-KCl-AlF3熔盐体系中加入质量分数为0.6%La_2O_3,利用电解法制备了Al-Mg-La合金.用ICP-OES(电感耦合等离子体光谱仪)和XRD进行了合金的组成和物相分析.研究结果表明,在电解温度800℃,阴极电流密度6.92A/cm2,槽电压5.3~5.4V,电解时间为1h的条件下,电流效率为86.2%,得到的合金主相为α-Mg基体、β-Al12Mg17相与Al11La3相.高的阴极电流密度有利于合金中镁含量的增加.     

航空铝合金预腐蚀疲劳寿命退化规律

航空铝合金材料在服役过程中常因腐蚀损伤而导致疲劳断裂问题,通过采用扫描电镜及疲劳寿命测试等方法,研究了不同预腐蚀损伤对2xxx铝合金在不同应力比下疲劳寿命的影响,探讨了预腐蚀损伤对疲劳裂纹萌生扩展的影响机理.结果表明:预腐蚀损伤对2xxx铝合金材料疲劳寿命的影响显著,材料的疲劳性能随着腐蚀损伤程度的增加而明显下降.同时建立了预腐蚀损伤对材料疲劳极限的影响系数C-T-R模型,材料疲劳极限的影响系数C随着预腐蚀时间的增加或者应力比R的增加而变大.断口分析表明,预腐蚀损伤的存在导致裂纹萌生寿命大大缩短,裂纹萌生由单源转变为多源,并且均萌生于腐蚀坑处.     

基于气基直接还原-熔分的硼铁矿高效利用新工艺

实验室条件下,以含硼铁精矿为原料制备氧化球团,对含硼铁精矿气基竖炉直接还原-电炉熔分新工艺进行了研究.结果表明,含硼铁精矿是良好的造球原料,1 200℃下焙烧20 min后,成品球团抗压强度可达2 500 N以上,满足气基竖炉直接还原工艺要求.在H2与CO体积比大于2/5且温度在850~1 000℃条件下,含硼铁精矿氧化球团还原率达到95%的时间为15~60 min,还原膨胀率不高于15%.在高温下电热熔化DRI后硼和铁可以高效分离,硼、铁收得率均可达到98%以上,富硼渣中B2O3的质量分数在21%以上,活性可达89%左右,是"一步法"生产硼酸的优良原料.含硼铁精矿气基竖炉直接还原电炉熔分新工艺可以实现硼铁高效分离和清洁利用.     

Enhanced mechanical properties of AZ31 magnesium alloy sheets by continuous bending process after V-bending

The effects of V-bending process, continuous bending process and combination process on the microstructure and mechanical properties and formability of an AZ31 magnesium alloy sheet were investigated. The experimental results showed that no twins were found in the microstructure of all samples after processes due to the fine grain. The V-bending and continuous bending processes were proved to be an effective approach to modify the mechanical properties and formability. While the samples after the combination process exhibited better mechanical properties and formability than the single processed sample. The yield strength significantly decreased with the value of 100 MPa and the fracture elongation enhanced to 18.3% at room temperature. The Erichsen value was 5.0 mm which was significantly increased by 117% compared with as-received sample. The superior formability of combination processed samples was mainly attributed to the smaller r-value and n-value.     

Effect of Mg substitution for La on microstructure, hydrogen storage and electrochemical properties of La1−xMgxNi3.5 (x=0.20, 0.23, 0.25 at%) alloys

The effect of Mg substitution for La on microstructure, hydrogen storage and electrochemical properties of the annealed La_(1-x) Mg_x Ni_3.5(x=0.20, 0.23, 0.25 at%) alloys have been studied. All the samples were mainly composed of(LaMg)_2Ni_7,(LaMg)Ni_3, and LaNi_5 phases. Mg substitution for La changed the phase abundance, but did not change the constitution of all phases, which is con fi rmed by the results of backscattered SEM images and EDS analysis. The P–C isotherms indicated that the La_(1-x) Mg_x Ni_3.5alloys reversibly absorbed and desorbed hydrogen smoothly at 298 K. The hydrogen absorption cyclic stabilities of La_(1-x) Mg_x Ni_3.5alloy after 5 hydrogen absorption/desorption cycles reached the maximum values of91.9% and 96.0% at 298 K and 323 K, respectively. The hydrogen desorption capacity and plateau pressure for the La_(1-x) Mg_x Ni_3.5alloy reached the maximum values of 1.055 H/M and 0.074 MPa, respectively. The desorption capacities of La_(1-x) Mg_x Ni_3.5reached 0.193 H/M and 0.565 H/M in the fi rst minute at 298 K and 323 K, respectively. Electrochemical property measurement indicated that La_(1-x) Mg_x Ni_3.5(x=0.20,0.23, 0.25 at%) alloys possessed excellent activation capability and were completely activated within3 cycles. Discharge capacities of La_(1-x) Mg_x Ni_3.5alloys reached 378.2 m A h/g(x = 0.20 at%), 342.7 m A h/g(x = 0.23 at%), and 369.6 m A h/g(x = 0.25 at%), respectively. Moreover, energy density of La_(1-x) Mg_x Ni_3.5alloy was much larger than that of La_0.80Mg_0.20Ni_3.5 alloy and nearly approaches the maximum value of La0.75Mg0.25Ni3.5. Thus, the La_(1-x) Mg_x Ni_3.5alloy exhibits optimum comprehensive properties of hydrogen storage and electrochemistry.     

Microstructure and properties of in-situ synthesized Cu-1 wt%TiC alloy followed by ECAP and post-annealing

A dispersion-strengthened copper alloy with 1 wt% TiC for commercial electrical-contact wires was prepared by in-situ reaction casting, grain-ultrafining by equal-channel angular pressing (ECAP) and subsequent annealing with aim to obtain excellent comprehensive performance. The results showed that fine TiC particles were in-situ synthesized in the as-cast Cu matrix and aggregated in clusters, and thus mechanical properties of the as-cast alloy deemed insufficient. Continued ECAP at 473 K significantly refined the grains of the as-cast alloy and improved the distribution of TiC particles. Due to multiple strengthening mechanisms, the ECAP-processed alloys maintained good conductivity with obviously enhanced tensile strength and hardness values. After post-ECAP annealing, the elongation and conductivity of the fine-grained copper alloy increased with the adequate tensile strength. The novel combined process endows the alloy appropriate performance to serve current high-frequency electrification railway systems.